BoP Lab / Michelin Raceway Road Atlanta

P2 vs STL vs FE2 vs FB pace at Michelin Raceway Road Atlanta

Quickest here: P2 1:22.533 Lucian Pancea, Atlanta Region Hoosier SCCA Super Tour @ Michelin Raceway Road Atlanta qualifying · STL 1:35.212 Danny Steyn, Atlanta Region Hoosier SCCA Super Tour @ Michelin Raceway Road Atlanta race · FE2 1:22.855 Paul Schneider, Atlanta Region Hoosier SCCA Super Tour @ Michelin Raceway Road Atlanta race

Lap times% of P2

P2STLFE2FBsolid race · dashed qualifying · slower is lower

P2STLFE2FBsolid race · dashed qualifying · each class's best lap as a share of P2's at the same event (the reference class, changeable above); 100% is level, higher is quicker

	Event	P2			STL					FE2					FB
	Event	Qual best	Race best	Trap	Qual best	Race best	Trap	vs P2	% of P2	Qual best	Race best	Trap	vs P2	% of P2	Qual best	Race best	Trap	vs P2	% of P2
	Atlanta Region SCCA Hoosier Super Tour @ Michelin Raceway Road Atlanta ST26MAR062026-03-06				1:37.000Danny Steyn · fastest of 15 · top 5 within 1.6s+0.012s (+0.01%)	1:36.825Danny Steyn · fastest of 14 · top 5 within 3.2s-0.382s (-0.39%)	126.5Derek Ketchie+6.5 mph (+5.4%)			1:24.639Paul Schneider · fastest of 7 · top 5 within 2.4s+1.503s (+1.81%)	1:24.978Paul Schneider · fastest of 7 · top 5 within 2.9s+1.478s (+1.77%)	138.5Paul Schneider+4.9 mph (+3.6%)
5 rule changes (STL: 3, FE2: 2)2 weight · 3 wording · STL minimum weights increase across all classes, 1300 cc gains 195 lbs to 1950, up to 1850 cc at 2500. · FE and FE2 Enterprises must use bubble tail P/N WM138014; FE2 allows only this configuration. · STL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs. · STL Mazda MX5 Challenge minimum weight now references GCR 9.1.7.1 instead of 2500 lbs; spec components removed, only alternative tires allowed. · FE2 allows driver safety and comfort modifications for disabled drivers with SCCA approval, not transferable to other drivers.showhide 2026-01-01 STL Weight adjustment for STL #39579weightslowerSTL minimum weights increase across all classes, 1300 cc gains 195 lbs to 1950, up to 1850 cc at 2500. 2025-10-01 FE2 FE & FE2 Bubble Tail #38978wordingwordingFE and FE2 Enterprises must use bubble tail P/N WM138014; FE2 allows only this configuration. 2025-08-01 STL Lotus Weight Reduction #38772weight -50 lbsfasterSTL/STU Lotus weight reduced: Evora GT4 to 2700 lbs, Elise Cup R to 2250 lbs, Elise/Exige SC to 2450-2550 lbs. 2025-05-01 STL E&O: SMX Allowance in STL #37945wordingunclearSTL Mazda MX5 Challenge minimum weight now references GCR 9.1.7.1 instead of 2500 lbs; spec components removed, only alternative tires allowed. 2025-04-01 FE2 Driver Safety & Comfort #37965wordingwordingFE2 allows driver safety and comfort modifications for disabled drivers with SCCA approval, not transferable to other drivers.
	Atlanta Region SCCA Hoosier Super Tour @ Michelin Raceway Road Atlanta ST25MAR072025-03-07				1:36.988Mike Taylor · fastest of 13 · top 5 within 2.0s+0.632s (+0.66%)	1:37.207Mike Taylor · fastest of 11 · top 5 within 1.3s+0.354s (+0.37%)	120.1Derek Ketchie+1.7 mph (+1.5%)			1:23.136Franklin Futrelle · fastest of 8 · top 5 within 2.1s-0.076s (-0.09%)	1:23.500Franklin Futrelle · fastest of 8 · top 5 within 1.9s-0.914s (-1.08%)	133.6Eric Wisniewski+1.7 mph (+1.3%)
4 rule changes (P2: 3, STL: 1)1 weight · 3 wording · P2 2000cc Pinto engine car minimum weight set to 1335 lbs. · STL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval. · P2 Spec ECU engine modifications clarified: oil system, ECU, and exhaust unrestricted only. · P2 FIA Group CN spec notes clarified: Series changed to Challenge, documentation requirement moved to online link.showhide 2024-12-01 P2 2000 cc Pinto Engine Car Weight #37187weightslowerP2 2000cc Pinto engine car minimum weight set to 1335 lbs. 2024-12-01 STL Request to Remove Miata Hubs from General category #37138wordingwordingSTL/STU: 90-05 Mazda Miata alternate front wheel hubs moved from General to specific part approval. 2024-05-01 P2 CN Spec ECU #35835wordingwordingP2 Spec ECU engine modifications clarified: oil system, ECU, and exhaust unrestricted only. 2024-05-01 P2 E&O - Correct FIA Group CN spec line notes #35900wordingwordingP2 FIA Group CN spec notes clarified: Series changed to Challenge, documentation requirement moved to online link.
	Atlanta Region Hoosier SCCA Super Tour @ Michelin Raceway Road Atlanta ST24MAR082024-03-08	1:24.228Lucian Pancea · fastest of 4 · top 4 within 5.2s+1.695s (+2.05%)	1:26.233Sherman Chao · fastest of 4 · top 4 within 17.9s+2.429s (+2.90%)	134.0Lucian Pancea-12.5 mph (-8.5%)	1:36.356Danny Steyn · fastest of 15 · top 5 within 3.3s-0.113s (-0.12%)	1:36.853Danny Steyn · fastest of 17 · top 5 within 2.8s+1.641s (+1.72%)	118.3Mike Taylor-8.8 mph (-6.9%)	+10.620squal +12.128s	112.3%qual 114.4%	1:23.212Franklin Futrelle · fastest of 14 · top 5 within 2.3s+0.084s (+0.10%)	1:24.414Charles Russell Turner · fastest of 13 · top 5 within 1.5s-0.040s (-0.05%)	131.9Jason Conzo-9.2 mph (-6.5%)	-1.819squal -1.016s	97.9%qual 98.8%
12 rule changes (P2: 7, STL: 5)3 engine · 2 induction · 7 wording · STL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems. · STL Acura/Honda B-series and Mazda MZR restrictors reduced 2mm; minimum weights down 25–75 lbs for 1900–2000cc engines. · STL Mazda 12A must keep 5th and 6th intake port actuators and valves, no longer allowed removal or disabling. · P2 AMAC modified engine range clarified to 2008 and older stock engines only, restrictor 38mm, weight 1025 lbs. · P2 Suzuki GSX-R1000 07/08 engine crankcase may swap to GSX-S1000 16/19 part #11301-04840. · STL Mazda RX-7 12A (79-85) now allows auto-type 2 bbl with 42mm choke(s) on dual-y manifold as alternate to stock Nikki 4 bbl. · P2 Table 1 corrects engine date ranges and brand specifications for Stock and Modified engines across multiple car models. · STL ITA/ITS RX7 and 1985+ ITA/ITS/ITB/ITC vehicles clarified to conform to section 9.1.4.2 tire specifications. · P2 side body height requirement clarified: outermost surface between wheel openings must equal front axle centerline height. · P2 closed cockpit single seat cars now prohibited unless specifically allowed in Table 1. · P2 engine table wording updated; redundant effective date language removed. · P2 motorcycle engines: 2011+ Kawasaki restrictor reduced to 34mm, minimum weight raised to 1100 lbs; 2009+ other brands weight raised to 1100 lbs.showhide 2024-02-01 STL ST Electric-Assisted Steering Systems #35066wordingwordingSTL and STU power steering rules clarified to permit electric-assisted and hydraulic-assisted steering systems. 2024-02-01 STL BOP Adjustments #35112inductionfasterSTL Acura/Honda B-series and Mazda MZR restrictors reduced 2mm; minimum weights down 25–75 lbs for 1900–2000cc engines. 2024-02-01 STL Mazda 12A #35320engineslowerSTL Mazda 12A must keep 5th and 6th intake port actuators and valves, no longer allowed removal or disabling. 2024-01-01 P2 E&O - Clarify B.1 modified engine range in AMAC spec lines #35225wordingwordingP2 AMAC modified engine range clarified to 2008 and older stock engines only, restrictor 38mm, weight 1025 lbs. 2024-01-01 P2 Replacement Engine Crankcase for 07/08 Suzuki GSX-R1000 Engines #35340engineunclearP2 Suzuki GSX-R1000 07/08 engine crankcase may swap to GSX-S1000 16/19 part #11301-04840. 2024-01-01 STL Alternate Carburetor Request for 79-85 RX7 12a #35181inductionunclearSTL Mazda RX-7 12A (79-85) now allows auto-type 2 bbl with 42mm choke(s) on dual-y manifold as alternate to stock Nikki 4 bbl. 2023-12-01 P2 Correct Table 1 for Engine Date Range Specifications #35182wordingwordingP2 Table 1 corrects engine date ranges and brand specifications for Stock and Modified engines across multiple car models. 2023-06-01 STL Clarify STL table B - IT spec notes on Tires #34187wordingwordingSTL ITA/ITS RX7 and 1985+ ITA/ITS/ITB/ITC vehicles clarified to conform to section 9.1.4.2 tire specifications. 2023-05-01 P2 Clarify minimum side body height requirement #34143wordingwordingP2 side body height requirement clarified: outermost surface between wheel openings must equal front axle centerline height. 2023-05-01 P2 Clarify closed cockpit single seat car allowance #34144wordingwordingP2 closed cockpit single seat cars now prohibited unless specifically allowed in Table 1. 2023-04-01 P2 Remove redundant effective date language and update engine table #34012wordingwordingP2 engine table wording updated; redundant effective date language removed. 2023-04-01 P2 E&O - Correct dimensional equivalents #34038engineslowerP2 motorcycle engines: 2011+ Kawasaki restrictor reduced to 34mm, minimum weight raised to 1100 lbs; 2009+ other brands weight raised to 1100 lbs.
	Atlanta Region Hoosier SCCA Super Tour @ Michelin Raceway Road Atlanta ST23MAR102023-03-10	1:22.533Lucian Pancea · fastest of 4 · top 4 within 4.2s-1.480s (-1.76%)	1:23.804Lucian Pancea · fastest of 4 · top 4 within 4.6s+0.733s (+0.88%)	146.5Lucian Pancea-3.5 mph (-2.4%)	1:36.469Danny Steyn · fastest of 16 · top 5 within 3.9s+0.493s (+0.51%)	1:35.212Danny Steyn · fastest of 17 · top 5 within 3.8s-0.267s (-0.28%)	127.1Mike Taylor+0.7 mph (+0.6%)	+11.408squal +13.936s	113.6%qual 116.9%	1:23.128Franklin Futrelle · fastest of 15 · top 5 within 2.5s+0.032s (+0.04%)	1:24.454Charles Russell Turner · fastest of 15 · top 5 within 1.2s+1.599s (+1.93%)	141.1Eric Cruz-3.0 mph (-2.1%)	+0.650squal +0.595s	100.8%qual 100.7%
8 rule changes (P2: 7, STL: 1)1 cars added · 1 engine · 6 wording · Sebeco NP01-EVO and Elan NP01 Mazda 2.0L MZR added to P2, 1600 lb minimum, no restrictor required. · P2 Radical SR3/SR4/Cup/Club Sport/Pro-Sport/PR6 removes assisted shifting requirement across all spec lines. · P2 chassis rules clarified to allow composite materials in non-fully-composite construction; anti-intrusion panel attachment standardized; Stohr and converted F600 cars added with specific allowances. · Unable to summarize: the change to P2 Engine Table Spec Line B.1 is not detailed in the provided text. · STL Spec MX5 clutch, wheels, and tyres specified: ACT 0000-02-5004-G6, 17x8 wheels, Toyo RR and RA1 235-40-17. · P2 chassis construction rules clarified: fully composite or partially composite requiring composite for mobility allowed; partial composite must roll without composite parts. · P2 classification wording cleaned up in GCR section 9.1.8.C and Contents. · P2 Oldsmobile cam rules clarify aftermarket manufacturer requirements; wording only.showhide 2023-01-01 P2 Request to Classify Sebeco NP01 #33378cars addedcars addedSebeco NP01-EVO and Elan NP01 Mazda 2.0L MZR added to P2, 1600 lb minimum, no restrictor required. 2023-01-01 P2 Radical spec line clarifications #33485wordingwordingP2 Radical SR3/SR4/Cup/Club Sport/Pro-Sport/PR6 removes assisted shifting requirement across all spec lines. 2023-01-01 P2 E&O original class intent #33519wordingwordingP2 chassis rules clarified to allow composite materials in non-fully-composite construction; anti-intrusion panel attachment standardized; Stohr and converted F600 cars added with specific allowances. 2023-01-01 P2 Update Engine Table Spec Line B.1 #33608engineunclearUnable to summarize: the change to P2 Engine Table Spec Line B.1 is not detailed in the provided text. 2023-01-01 STL Spec MX5 in STL #33473wordingwordingSTL Spec MX5 clutch, wheels, and tyres specified: ACT 0000-02-5004-G6, 17x8 wheels, Toyo RR and RA1 235-40-17. 2022-05-01 P2 E&O Clarification of Chassis Construction Requirements #32469wordingwordingP2 chassis construction rules clarified: fully composite or partially composite requiring composite for mobility allowed; partial composite must roll without composite parts. 2022-05-01 P2 Clean up P2 wording #32525wordingwordingP2 classification wording cleaned up in GCR section 9.1.8.C and Contents. 2022-04-01 P2 After Market to Aftermarket #32373wordingwordingP2 Oldsmobile cam rules clarify aftermarket manufacturer requirements; wording only.
	Atlanta Region Hoosier SCCA Super Tour @ Michelin Raceway Road Atlanta ST22MAR122022-03-12	1:24.013Robert Iversen · fastest of 6 · top 5 within 3.1s-3.393s (-3.88%)	1:23.071Robert Iversen · fastest of 6 · top 5 within 4.0s-3.049s (-3.54%)	150.1Robert Iversen+13.2 mph (+9.6%)	1:35.976Danny Steyn · fastest of 18 · top 5 within 2.9s-0.449s (-0.47%)	1:35.479Danny Steyn · fastest of 18 · top 5 within 3.2s-1.326s (-1.37%)	126.3Trever Degioanni+2.5 mph (+2.1%)	+12.408squal +11.963s	114.9%qual 114.2%	1:23.096Paul Schneider · fastest of 13 · top 5 within 2.8s-1.268s (-1.50%)	1:22.855Paul Schneider · fastest of 13 · top 5 within 2.5s-1.101s (-1.31%)	144.1Bailey Monette+5.2 mph (+3.8%)	-0.216squal -0.917s	99.7%qual 98.9%
24 rule changes (P2: 13, STL: 11)3 engine · 2 aero · 2 cars added · 2 induction · 1 tyres & wheels · 1 weight · 13 wording · P2 adds Beasley B2 spec line with 1350 lbs, Mazda 12A, 40.5mm venturi, 16.5in wing. · P2 wing specs correct terminology from 'cord' to 'chord' for 16.5in single or dual element wings. · P2 Converted F5 cars reclassified as Converted F500 cars; suspension must comply with F500 requirements, minimum width 55 inches. · STU normally aspirated engines: minimum weights reduced up to 310 lbs; single throttle body weight reduction removed. · STL and STU Improved Touring vehicles must conform to 9.1.4 Tires & Wheels requirements. · P2 motorcycle engines increase to 1505cc max, two-stroke to 1205cc max; automotive engines gain 50 lbs minimum weight to 1350. · P2 Control Area definition narrowed; aerodynamic attachments and vertical structures like turning vanes now prohibited. · STL and STU piston engines clarified: intake manifold and cylinder head porting remains free. · STL Mazda Renesis flat plate restrictor increases from 55mm to 60mm. · STL Mazda RX-7 12A 79-85 clarifies carburetor, emissions, and water jacket modification rules. · P2 Engine Table Spec Line B.1 changed effective 1-1-22, details not provided in excerpt. · P2 Control Area definition clarified: floor extensions and aerodynamic attachments on bottom or top side now explicitly included. · P2 CN Honda K20A-FD2 engine rebuild rules clarified: machining prohibition replaced with specific restrictions on balancing, porting, polishing, valve jobs, cylinder honing. · STL Spec MX-5 removes redundant specification line; no performance change. · Converted F5 cars in P2 minimum width reduced to 55 inches from F5 spec. · P2 clarifies minimum body width requirement between front and rear wheels for Ralt RT40, RT41, Swift 008, 014. · STL Volkswagen 2.0L TFSI 1984cc classified with turbocharger removal required, meeting all other STL specs. · P2 tonneau covers now allowed to meet minimum dimensions; equipment attachment requirements clarified. · P2 multiple chassis models remove effective dates from Table 1 specifications. · P2 engines limited to 4 valves per cylinder maximum across all three spec lines. · STL Pontiac Solstice/Saturn Sky allowed 4" ride height. · STL Mazda B5 DOHC added to classification with standard STL regulations. · STL Honda B16A JDM restrictor reduced from 54mm to 53mm. · ST oil coolers and filters now explicitly allowed to be added or substituted; wording clarifies existing permissions.showhide 2022-03-01 P2 Add spec line for Beasley B2 #32147cars addedcars addedP2 adds Beasley B2 spec line with 1350 lbs, Mazda 12A, 40.5mm venturi, 16.5in wing. 2022-03-01 P2 E&O Table 1 spec line wing terminology #32148wordingwordingP2 wing specs correct terminology from 'cord' to 'chord' for 16.5in single or dual element wings. 2022-03-01 P2 E&O class name #32196wordingwordingP2 Converted F5 cars reclassified as Converted F500 cars; suspension must comply with F500 requirements, minimum width 55 inches. 2022-03-01 STL Single TB Weight Modifiers #31449weightfasterSTU normally aspirated engines: minimum weights reduced up to 310 lbs; single throttle body weight reduction removed. 2022-03-01 STL Improved Touring Tires #32063tyres & wheelstyres & wheelsSTL and STU Improved Touring vehicles must conform to 9.1.4 Tires & Wheels requirements. 2022-02-01 P2 E&O Engine section #31969enginefasterP2 motorcycle engines increase to 1505cc max, two-stroke to 1205cc max; automotive engines gain 50 lbs minimum weight to 1350. 2022-01-01 P2 E&O letter #31539 – Control Area definition #31783aeroslowerP2 Control Area definition narrowed; aerodynamic attachments and vertical structures like turning vanes now prohibited. 2022-01-01 STL Throttling Device Clarification #31323wordingwordingSTL and STU piston engines clarified: intake manifold and cylinder head porting remains free. 2022-01-01 STL Mazda Renesis Restriction #31467inductionfasterSTL Mazda Renesis flat plate restrictor increases from 55mm to 60mm. 2022-01-01 STL Clarification of 79-85 RX7 Spec line #31621wordingwordingSTL Mazda RX-7 12A 79-85 clarifies carburetor, emissions, and water jacket modification rules. 2021-12-01 P2 BoP adjustment effective 1-1-22 #31538wordingunclearP2 Engine Table Spec Line B.1 changed effective 1-1-22, details not provided in excerpt. 2021-12-01 P2 E&O clarification of "Control Area" definition #31539wordingwordingP2 Control Area definition clarified: floor extensions and aerodynamic attachments on bottom or top side now explicitly included. 2021-09-01 P2 P2 CN Engine Rebuild Clarification #31000wordingwordingP2 CN Honda K20A-FD2 engine rebuild rules clarified: machining prohibition replaced with specific restrictions on balancing, porting, polishing, valve jobs, cylinder honing. 2021-09-01 STL Request to clean up Spec MX-5 Redundancy #31069wordingwordingSTL Spec MX-5 removes redundant specification line; no performance change. 2021-08-01 P2 F5 P2 Conversion #30856aerofasterConverted F5 cars in P2 minimum width reduced to 55 inches from F5 spec. 2021-08-01 P2 Clarify minimum body width requirement #30859wordingwordingP2 clarifies minimum body width requirement between front and rear wheels for Ralt RT40, RT41, Swift 008, 014. 2021-06-01 STL VW Engine Request #30625engineslowerSTL Volkswagen 2.0L TFSI 1984cc classified with turbocharger removal required, meeting all other STL specs. 2021-05-01 P2 E&O tonneau cover provision in cockpit opening section #30459wordingwordingP2 tonneau covers now allowed to meet minimum dimensions; equipment attachment requirements clarified. 2021-05-01 P2 Remove effective dates in Table 1 #30468wordingwordingP2 multiple chassis models remove effective dates from Table 1 specifications. 2021-05-01 P2 E&O Maximum Valves Per Cylinder #30560engineengineP2 engines limited to 4 valves per cylinder maximum across all three spec lines. 2021-05-01 STL Solstice Ride Height #30183wordingwordingSTL Pontiac Solstice/Saturn Sky allowed 4" ride height. 2021-05-01 STL Request Mazda B5 DOHC #30420cars addedcars addedSTL Mazda B5 DOHC added to classification with standard STL regulations. 2021-05-01 STL Honda B16A (JDM) Restrictor change #30531inductionslowerSTL Honda B16A JDM restrictor reduced from 54mm to 53mm. 2021-04-01 STL ST Oil Coolers E&O Correction to 9.1.4.2.H #30388wordingwordingST oil coolers and filters now explicitly allowed to be added or substituted; wording clarifies existing permissions.
	Atlanta Region Hoosier SCCA Super Tour @ Michelin Raceway Road Atlanta ST21MAR192021-03-19	1:27.406Lucas Mann · fastest of 4 · top 4 within 5.9s	1:26.120Lucian Pancea · fastest of 3 · top 3 within 3.8s	136.9Lucian Pancea	1:36.425Danny Steyn · fastest of 24 · top 5 within 3.0s	1:36.805Danny Steyn · fastest of 22 · top 5 within 3.1s	123.8Eric Diaz	+10.685squal +9.019s	112.4%qual 110.3%	1:24.364Bailey Monette · fastest of 18 · top 5 within 1.3s	1:23.956Bailey Monette · fastest of 18 · top 5 within 0.8s	138.9T Vanacore	-2.164squal -3.042s	97.5%qual 96.5%
50 earlier rule changes on record, in force before Atlanta Region Hoosier SCCA Super Tour @ Michelin Raceway Road Atlanta (from 2019)15 induction · 7 cars added · 5 weight · 3 aero · 3 engine · 16 wording · 1 other · P2 adds new spec line for 2-cycle 3-cylinder engine up to 820cc with 10 front and 14-15 rear wheel width. · STL GM Ecotec engines now permit any combination within the family, must use 55mm flat plate restrictor. · STL/STU 90-05 Mazda Miata gains approval for Mazda Motorsports Development alternate front wheel hubs. · ST cars may relocate ABS actuation hardware and wiring anywhere in engine compartment. · STL rear wing trailing edge, including end plates and gurney flap, maximum rearward mounting clarified to center of rearmost bodywork. · STL allows OEM gear sets from same manufacturer transmissions with input shaft modifications for fitment. · STL RWD strut suspension weight penalty cut to 0.5%, other RWD cut to 2.5%. · STL Honda F20C loses 2% weight penalty, minimum weight reduced by approximately 35 lbs. · STL Honda B16/B17/B18C1 restrictor tightened to 53mm; B18C variants and Mazda MZR to 52mm. · P2 Honda K20A-FD2 intake restrictor reduced from 55mm to 50mm, making cars faster. · ST aero devices and reference areas now include end plates but exclude fasteners protruding over 1/2 inch. · FE2 oil cooler wording clarified: optional air-to-oil cooler allowed, Setrab 50-625-7612 or equivalent max 13 inches wide by 6.5 inches high. · P2 rear wing requirements clarified: standard wing 6×12 inches, end plates 14-inch square; alternate 110cm width wing 9×18 inches, end plates 14×18 inches. · STL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis adjustments. · STL and STU rear wing rules clarify that wicker is a Gurney flap; no performance change. · GT3 and STU add Borg-Warner EFR6258 to approved turbocharger list. · Elan NP01 classified in P2 Table 1 as Spec Line car with 2000cc displacement and P2 Engine Table restrictor. · STL adds 2016-2019 Mazda MX-5 Global Cup at 2000cc, 2450-2550 lbs minimum weight. · STL Mazda MX-5 Club Model 06-15 allows Mazda header part number 0000-06-5407-NC. · STL Honda/Acura B18 non-C gets 54mm restrictor; B18C variants drop B18C1, get 53mm restrictor. · P2 Enterprises Sports Racer adds 55mm flat plate intake restrictor Part # WM303013 as alternative to SIR. · STL Honda B18 restrictor reduced from 54mm to 53mm flat plate; B18C1 added with 54mm restrictor. · P2 Enterprise Sports Racer 2.3L engine now requires SIR or Flat Plate restrictor sized in 0.5mm increments. · STU GM Ecotech LNF now allowed with turbo removed or with LE5 head and intake manifold, meeting STL specs. · STL Mazda MZR restrictor reduced from 54 mm to 53 mm. · STL Mazda MZR restrictor reduced from 55 mm to 53 mm. · P2 fly-by-wire throttle control wording clarified: stock ECUs with drive-by-wire must activate original throttle shaft mechanism. · STL Mazda Spec MX5 Challenge adds approved wheel part numbers 0000-04-5706-GM, 0000-04-5706-SL. · P2 adds BMW to motorcycle-based engine options in 4-cycle line alongside Kawasaki, Suzuki, Yamaha, Honda. · FE and FE2 minimum weight increased to 1270 lbs including driver; spring options and tire warmer ban added. · P2 Honda K20A-FD2 non-composite chassis must use 55mm flat plate intake restrictor at 1500 lbs minimum weight. · Mazda Spec MX-5 Challenge classified in STL with 2000cc displacement and 2500 lbs minimum weight. · P2 motorcycle engines: Stock restrictor 36.5mm to 35mm, modified 37.5mm to 34mm; B.5 restrictor 37.5mm to 33mm. All weights increase 25 lbs. · P2 cars limited to power application on maximum two wheels, effective 2019-07-01. · STU alternate intake manifolds now allowed case-by-case instead of prohibited. · P2 Enterprise minimum weight increases to 1375 lbs; peak horsepower of sealed ESR engine reduced per CRB specification. · STL Acura/Honda B18 except C engine restrictor increases from 53mm to 54mm flat plate. · STL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. · P2 stock engine restrictor shrinks to 35.0mm and weight rises to 1025 lbs; modified engine restrictor to 34.0mm, weight to 1125 lbs; line B.5 restrictor to 33.0mm, weight to 1185 lbs. · P2 Line A.1 restrictor reduced from 40mm to 38mm. · STL adds VW 1.8L R4 20VT 1781cc, 1 minimum weight, turbo removed permitted. · STL Mazda Renesis minimum weight reduced from 2800 to 2700 lbs. · STL Mazda MX-5 Cup brake pad compound changed to open. · STL adds Acura/Honda B18C1 GSR with 54mm flat plate restrictor and port matching limited to 1 inch. · STL Mazda 12 and 13B now permit port matching; previous ban removed. · P2 Spec Line cars now allow 1345cc Hayabusa stock engines at 1050 lbs with 30mm restrictor. · P2 Group CN Honda K20A-FD2 55mm restrictor implementation delayed from 1/1/2019 to 3/1/2019. · P2 Honda K20A-FD2 in CN chassis must use stock intake manifold with 64mm throttle body and 55mm restrictor at 1500 lbs minimum weight. · STL B18C Type R variants get 54mm flat plate restrictor; B17 also gets 54mm restrictor. · STL Mazda Miata removes maximum displacement limit and adjusts minimum weight.showhide 2021-03-01 P2 Add a new spec line for a 2-cycle, 3-cylinder engine up to 820cc #30272cars addedcars addedP2 adds new spec line for 2-cycle 3-cylinder engine up to 820cc with 10 front and 14-15 rear wheel width. 2021-03-01 STL GM Ecotec engines in STL #30247wordingwordingSTL GM Ecotec engines now permit any combination within the family, must use 55mm flat plate restrictor. 2021-03-01 STL Super Touring Alternate Miata Hubs #30345wordingwordingSTL/STU 90-05 Mazda Miata gains approval for Mazda Motorsports Development alternate front wheel hubs. 2021-02-01 STL Brake Component Relocation #29990wordingwordingST cars may relocate ABS actuation hardware and wiring anywhere in engine compartment. 2021-02-01 STL Super Touring Wing Clarification #30111aeroaeroSTL rear wing trailing edge, including end plates and gurney flap, maximum rearward mounting clarified to center of rearmost bodywork. 2021-02-01 STL Transmission Options #30118wordingwordingSTL allows OEM gear sets from same manufacturer transmissions with input shaft modifications for fitment. 2021-01-01 STL Request for FWD and RWD Parity #29728weightfasterSTL RWD strut suspension weight penalty cut to 0.5%, other RWD cut to 2.5%. 2021-01-01 STL Request to Remove Honda F20C 2% Weight Penalty #29815weightfasterSTL Honda F20C loses 2% weight penalty, minimum weight reduced by approximately 35 lbs. 2021-01-01 STL Request for FWD and RWD Parity #30023inductionslowerSTL Honda B16/B17/B18C1 restrictor tightened to 53mm; B18C variants and Mazda MZR to 52mm. 2020-12-01 P2 Balance of Performance adjustments effective 01-01-2021 #29822inductionfasterP2 Honda K20A-FD2 intake restrictor reduced from 55mm to 50mm, making cars faster. 2020-12-01 STL Request clarification on wing measurement #29640aeroaeroST aero devices and reference areas now include end plates but exclude fasteners protruding over 1/2 inch. 2020-09-01 FE2 FE/FE2 Oil Cooler #29293wordingwordingFE2 oil cooler wording clarified: optional air-to-oil cooler allowed, Setrab 50-625-7612 or equivalent max 13 inches wide by 6.5 inches high. 2020-09-01 P2 E&O clarification of P2 rear wing requirements #29205aeroaeroP2 rear wing requirements clarified: standard wing 6×12 inches, end plates 14-inch square; alternate 110cm width wing 9×18 inches, end plates 14×18 inches. 2020-08-01 STL Minimum Weight Determination #27695wordingwordingSTL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis adjustments. 2020-08-01 STL ST Gurney flap Wicker clarification #29012wordingwordingSTL and STU rear wing rules clarify that wicker is a Gurney flap; no performance change. 2020-07-01 STL Request for Addition to GT3 Approved Turbo List #27576wordingwordingGT3 and STU add Borg-Warner EFR6258 to approved turbocharger list. 2020-06-01 P2 Classify Elan NP01 in P2 Table 1 #28812cars addedcars addedElan NP01 classified in P2 Table 1 as Spec Line car with 2000cc displacement and P2 Engine Table restrictor. 2020-06-01 STL Request to add 2016-2019 GMX-5 Spec line #28604cars addedcars addedSTL adds 2016-2019 Mazda MX-5 Global Cup at 2000cc, 2450-2550 lbs minimum weight. 2020-06-01 STL Request to update PN for MX-5 #28622wordingunclearSTL Mazda MX-5 Club Model 06-15 allows Mazda header part number 0000-06-5407-NC. 2020-06-01 STL Correction - Clarification Honda/Acura B18B engine Letter # 26209 #28873inductionunclearSTL Honda/Acura B18 non-C gets 54mm restrictor; B18C variants drop B18C1, get 53mm restrictor. 2020-05-01 P2 SCCA Enterprises ESR / P2 engine restrictor testing #28669engineengineP2 Enterprises Sports Racer adds 55mm flat plate intake restrictor Part # WM303013 as alternative to SIR. 2020-05-01 STL STL Honda B18 restrictor changes #28794inductionfasterSTL Honda B18 restrictor reduced from 54mm to 53mm flat plate; B18C1 added with 54mm restrictor. 2020-04-01 P2 Add ESR inlet restrictor #27869inductionslowerP2 Enterprise Sports Racer 2.3L engine now requires SIR or Flat Plate restrictor sized in 0.5mm increments. 2020-04-01 STL Change GM LNF 2.0 Allowance to LSJ Engine for Viable STL 2.0 #27884engineslowerSTU GM Ecotech LNF now allowed with turbo removed or with LE5 head and intake manifold, meeting STL specs. 2020-04-01 STL Acura/Honda B18C engine chart. Reduce the current 54 mm flat plat #28663inductionslowerSTL Mazda MZR restrictor reduced from 54 mm to 53 mm. 2020-04-01 STL Mazda MZR engine chart. Reduce the current 55 mm flat plate to 53 #28664inductionslowerSTL Mazda MZR restrictor reduced from 55 mm to 53 mm. 2020-03-01 P2 Request for Fly by Wire Rule Wording Change #28247wordingwordingP2 fly-by-wire throttle control wording clarified: stock ECUs with drive-by-wire must activate original throttle shaft mechanism. 2020-03-01 STL Request to add wheel part numbers #28342wordingwordingSTL Mazda Spec MX5 Challenge adds approved wheel part numbers 0000-04-5706-GM, 0000-04-5706-SL. 2020-01-01 P2 Request for addition of BMW Engine in P2 Engine Table #27821cars addedcars addedP2 adds BMW to motorcycle-based engine options in 4-cycle line alongside Kawasaki, Suzuki, Yamaha, Honda. 2019-12-01 FE2 FE / FE2 Update Rules #27624weightslowerFE and FE2 minimum weight increased to 1270 lbs including driver; spring options and tire warmer ban added. 2019-10-01 P2 Update Engine Table Line E notes #27414inductionslowerP2 Honda K20A-FD2 non-composite chassis must use 55mm flat plate intake restrictor at 1500 lbs minimum weight. 2019-10-01 STL Request to Classify Spec MX-5 Challenge in STL #27399cars addedcars addedMazda Spec MX-5 Challenge classified in STL with 2000cc displacement and 2500 lbs minimum weight. 2019-08-31 P2 Update P2 Engine Table spec lines to reflect 3/1/2019 #27254inductionslowerP2 motorcycle engines: Stock restrictor 36.5mm to 35mm, modified 37.5mm to 34mm; B.5 restrictor 37.5mm to 33mm. All weights increase 25 lbs. 2019-07-01 P2 E&O Transmissions #27006otherslowerP2 cars limited to power application on maximum two wheels, effective 2019-07-01. 2019-07-01 STL Request clarification for manifold and throttle in STU #27004inductionfasterSTU alternate intake manifolds now allowed case-by-case instead of prohibited. 2019-06-01 P2 Request to restrict all cars #26246weightslowerP2 Enterprise minimum weight increases to 1375 lbs; peak horsepower of sealed ESR engine reduced per CRB specification. 2019-05-31 STL Request Restrictor Plate correction #26779inductionfasterSTL Acura/Honda B18 except C engine restrictor increases from 53mm to 54mm flat plate. 2019-05-01 STL Request Ride Height Clarification #26597wordingwordingSTL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. 2019-03-01 P2 Change Engine Table Lines B.1 & B.5 #25777inductionslowerP2 stock engine restrictor shrinks to 35.0mm and weight rises to 1025 lbs; modified engine restrictor to 34.0mm, weight to 1125 lbs; line B.5 restrictor to 33.0mm, weight to 1185 lbs. 2019-03-01 P2 Change Line A.1 restrictor size #26429inductionslowerP2 Line A.1 restrictor reduced from 40mm to 38mm. 2019-03-01 STL Request to Allow VW 1.8L Engine #25614cars addedcars addedSTL adds VW 1.8L R4 20VT 1781cc, 1 minimum weight, turbo removed permitted. 2019-03-01 STL Request to reduce weight of RX8 with Renesis rotary #25781weight -100 lbsfasterSTL Mazda Renesis minimum weight reduced from 2800 to 2700 lbs. 2019-03-01 STL Request for Open Brake Pads On Mazda MX-5 Cup NC #25821wordingwordingSTL Mazda MX-5 Cup brake pad compound changed to open. 2019-03-01 STL Request to clarify B18C1 GSR Honda B motor table #26209cars addedcars addedSTL adds Acura/Honda B18C1 GSR with 54mm flat plate restrictor and port matching limited to 1 inch. 2019-03-01 STL Port Matching #26415wordingfasterSTL Mazda 12 and 13B now permit port matching; previous ban removed. 2019-01-01 P2 Request to Allow 1345cc Hayabusa Engines for Spec Line P2 Cars #25595enginefasterP2 Spec Line cars now allow 1345cc Hayabusa stock engines at 1050 lbs with 30mm restrictor. 2019-01-01 P2 Change CN inlet restrictor implementation date #25816wordingwordingP2 Group CN Honda K20A-FD2 55mm restrictor implementation delayed from 1/1/2019 to 3/1/2019. 2019-01-01 P2 Clarify Honda K20A-FD2 parts requirement #25950inductionslowerP2 Honda K20A-FD2 in CN chassis must use stock intake manifold with 64mm throttle body and 55mm restrictor at 1500 lbs minimum weight. 2019-01-01 STL Request to equalize FPR Reduction on all B-Series Vtec Engines #24746inductionslowerSTL B18C Type R variants get 54mm flat plate restrictor; B17 also gets 54mm restrictor. 2019-01-01 STL Request E&O for Mazda Miata Spec Line #25955wordingunclearSTL Mazda Miata removes maximum displacement limit and adjusts minimum weight.

Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. "% of P2" is the class's best as a share of P2's best at the same event (100% is level, less is quicker): weather and track condition move every class together, so this compares across years where the raw times do not. It still breaks when P2's own field changes or one session was wet and another dry. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.