P2 + SRF + FF at Michelin Raceway Road Atlanta

In F500, GCR Section 9.1.1.D.15.D., change as follows:
"Stand-alone after market aftermarket ECUs are not permitted."
In P2, GCR Section 9.1.8.F.3.a., change as follows:
"As manufactured and ground by Oldsmobile or by an after after market aftermarket cam manufacturer to Oldsmobile factory
specifications for Vin.A (W41) or Mantapart #OP 1149."
In P2, GCR Section 9.1.8.F.3.b., change as follows:
"As manufactured and ground by Oldsmobile or by an after market aftermarket cam manufacturer to Oldsmobile factory profile
Vin. D or Mantapart #OP 1148."

In P2, GCR section 9.1.8.C.A.1, add the following:
"Chassis fully composed of composite structural materials or chassis partially composed of composite materials that is not
capable of rolling on its wheels without the composite materials being installed."
In P2, GCR section 9.1.8.C.C.1, add the following:
"Allow for any form of chassis construction except fully composite chassis. A chassis partially composed of composite materials
must satisfy the requirements of section 9.4.5.A, B, C, E, F and be capable of rolling on its wheels without the composite materials
being installed."

In P2, GCR section 9.1.8.C, change as follows:
"PROTOTYPE 2 (P2) CLASSIFICATION"
In GCR CONTENTS, change as follows:
"PROTOTYPE 2 (P2) CLASSIFICATION"

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Tires: must be run as delivered."

In SRF, GCR section 9.1.8.D.1.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall be used as delivered with no
machining of any kind. Minimum thickness 13.25 12.20mm (0.522 0.481"). The 1985 Renault Alliance solid front rotor (Reference:
Bendix PRT1318 or Centrix 121.11004) may be used on front, rear, or both axles, but each axle must be paired to the same type
rotor. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185."
In SRF, GCR section 9.1.8.D.2.H, change as follows:
"No performance M modifications of any kind.
SCCA Enterprises’ seals shall be intact.
(2) on cam cover, (2) on the oil pan, (1) on the each cam shaft. Automatic Drivetrain Violation if removed."
In SRF, GCR section 9.1.8.D.2.H.23, change as follows:
"Air Filter: P/N WM301020 or K&N RC-9160"

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)
Marque
Wheelbase inches
max/ Track Max
inches
Weight Displacement Engine Restrictor Notes

A specification table follows in the original; it is not shown here.

In P2 Table 1, Radical SR3/SR4 spec line, make the following change:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

In P2, GCR section 9.1.8.A.1, change as follows:
"Chassis fully composed of composite structural materials or chassis partially composed of composite materials that is not
capable of rolling on its wheels without the composite materials being installed."
In P2, GCR section 9.1.8.C.C.1, change as follows:
"Allow for any form of chassis construction except fully composite chassis incorporating composite structural materials. A chassis
partially composed of composite materials must satisfy the requirements of section 9.4.5.A, B, C, E, F, and be capable of rolling
on its wheels without the composite materials being installed. Both tube frame and aluminum or steel monocoque chassis
construction are allowed.”
In P2, GCR section 9.1.8.C.2, change as follows:
"Anti-intrusion panels are allowed anywhere on the sides of the chassis. Materials and attachment
are is unrestricted. Attachment points must be at least 15cm (5.906 inches) apart center to center using fasteners no larger than
6.5mm (0.256 inches) diameter.”
In P2 Table 1, add the following:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

In SRF, GCR section 9.1.8.D.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall be used as delivered with no
machining of any kind. Minimum thickness 12.20mm (0.481"). The 1985 Renault Alliance solid front rotor (Reference: Bendix
PRT1318 or Centrix 121.11004) may be used on front, rear, or both axles, but each axle must be paired to the same type
rotor. The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N
1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other
modification allowed. Wilwood caliper with bracket universal fit P/N 800038 may be used as delivered with no modification of
any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind;
maximum of one spring per caliper."
P2 Engine Table
Spec
Line Engine Series

A specification table follows in the original; it is not shown here.

In FC/FF, GCR section 9.1.1.B.14.a.6, change as follows:
"For all Honda part numbers in these specifications, superc seding part numbers are considered equivalent.
In FC/FF, GCR section 9.1.1.B.14.f.5, change as follows:
"Cylinder head breather restrictor must be used as supplied by HPD or Fast Forward, unmodified.: HPD PN: 15262-F21S-A200; Fast
Forward PN: FF200-503."
In FC/FF, GCR section 9.1.1.B.14.k.2, change as follows:
"The upper manifold, air box and throttle body assembly must be used as delivered from Honda, HPD, or Fast Forward as noted
below."
In FC/FF, GCR section 9.1.1.B.14.k.2, insert as follows:
"a. Intake manifold: HPD PN: 17210-F21S-A210; Fast Forward PN: FF200-201.
b. Throttle body: Honda Fit: PN: 16400ZZ5024; HPD PN: 16400ZZ5024; Fast Forward PN: FF200-104.
c. Throttle lever: HPD PN: 17330-F21S-A210; Fast Forward PN: FF200-101."
In FC/FF, GCR section 9.1.1.B.14.k.3, change as follows:
"All gaskets and sensors utilized on the inlet manifold from head to throttle body must be Honda Fit OEM, or HPD supplied or Fast
Forward as noted below.
a. Gasket In. manifold: HPD PN: 17105-RB0-004, Honda Fit OEM.
b. Gasket, EGR chamber cover: HPD PN: 17146-RB0-004, Honda Fit OEM.
c. Gasket In. port: HPD PN: 17115-RB0-007, Honda Fit OEM.
d. Gasket, restrictor: HPD PN: 17399-F21S-A200, (2 required) HPD; Fast Forward PN: FF200-109. Two required."
In FC/FF, GCR section 9.1.1.B.14.k.5, change as follows:
"The Honda Fit engine is required to have an HPD supplied air inlet restrictor supplied by HPD or Fast Forward: HPD PN: 17344-
F21S-A201; Fast Forward PN: FF200-110, with internal diameter of 30.5mm and thickness of 3.175mm (0.125 inches) correctly
installed within the intake system."
In FC/FF, GCR section 9.1.1.B.14.m.1, change as follows:
"The exhaust manifold must be as supplied by HPD or Fast Forward:, HPD part # PN: 18150-F21S-A200 or # PN: 1818 50-F21S-B200;
Fast Forward PN: FF500-001 or PN: FF500-002."
In FC/FF, GCR section 9.1.1.B.14.n.1, change as follows:
"The oil pan, baffle plate, and scavenge pump filter fittings must be as supplied by HP or Fast Forward as noted below. No
modifications are permitted.
a. Oil pan: HPD PN: 11200-F21S-A210 or PN: 11200-F21S-C240; Fast Forward PN: FF100-201A or PN: FF100-201B.
b. Oil pan baffle plate: HPD PN: 11221-F21S-A210; Fast Forward PN: FF100-202.
c. Oil scavenge pump filter fittings (2 required): HPD PN: 15180-F21S-A210; Fast Forward PN: FF100-204."
In FC/FF, GCR section 9.1.1.B.14.n.3, change as follows:
"The scavenge pump and internal scavenge pump parts must be as supplied from HPD or Fast Forward as noted below."
In FC/FF, GCR section 9.1.1.B.14.n.3, change as follows:
"b. Rotor outside diameter: HPD 44.400mm (1.748 inches):; Fast Forward 40.640mm (1.600 inches).
c. Scavenge pump rotor set: HPD PN: 15450-F21S-A20; Fast Forward PN: FF100-110.
d. Oil pump: HPD PN: 15100-F21S-A200; Fast Forward PN: FF100-100A.
e. Scavenge pump cartridge: 15111-F21S-A21; Fast Forward PN: FF100-127.
f. Scavenge pump port A: HPD PN: 15137-F21S-A20; Fast Forward PN: FF100-101.
g. Scavenge pump port B: HPD PN: 15139-F21S-A20; Fast Forward PN: FF100-102.
h. Scavenge pump shaft: HPD PN: 15510-F21S-A20; Fast Forward PN: FF100-103.
i. Scavenge pump front cover: HPD PN: 15070-F21S-A21; Fast Forward PN: FF100-104."

In P2 Engine Table, Spec Line B.1, change as follows:

In P2, GCR section 9.1.8.C.D.2, change as follows:
"Height: No part of the vehicle having special or significant aerodynamic function shall exceed a height of 115cm (45.275 inches)
above the ground with the car in normal racing trim, driver aboard."
In P2, GCR section 9.1.8.C.D.3, change as follows:
"However, no portion shall extend more than 10cm (3.937 inches) beyond a plane tangent to the outer face of the front and rear
wheels with tires."
P2 Engine Table
Spec
Line Engine Series

A specification table follows in the original; it is not shown here.

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Front – Hoosier P/N 46100 1 P185/65R13 W2"

In P2, GCR section 9.1.8.C.D.6, change as follows:
"As viewed from the side, T the outermost surface of side pods body between the front and rear wheel openings and above the
floor must have a minimum height equal to the height of the front axle centerline."

In P2, GCR section 9.1.8.C.C, add a section as follows:
"4. Closed cockpit single seat cars are not permitted unless specifically allowed by a spec line in Table 1."

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5" with driver as raced when P185/60R13 (H20 or W2) tires are used."

In SRF, GCR section 9.1.8.D.1.V.j, change as follows:
"Radiator - Enterprises new style P/N 480465 (requires baffle P/N 480464) or P/N 480466 can be used. P/N 480466, may can be
replaced with Automotive P/N 1R698, CU698 or equivalent OEM manufacturer justified by one cross-reference chart equivalent,
as long as the size, shape, and material are the same as the original P/N. The capacity, core thickness, etc., cannot be changed
even if allowed under the above. The competitor is responsible for providing this documentation of the cross-reference P/N."

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

In SRF, GCR section 9.1.8.D.1.W.l, change as follows:
"A Super Bright LEDs Inc. rain / brake light comprised of a single standard trailer oval lamp, 2-1/4 inches x 6-1/2 inches, with
incandescent or LED illumination, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes
GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the
wiring harness. The secondary filament of the brake light assembly shall must be connected to a switch enabling its use as a rain
light."

In SRF, GCR section 9.1.8.D.1.W.l, change as follows:
"A Super Bright LEDs Inc. P/N PT-STRB-R24 (SCCA Enterprises P/N 180427A) rain / brake light, P/N PT-STRB-R24, is required in the
original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No
changes may be made to the original 3-pin connector on the wiring harness. An SCCA Enterprises P/N 1190503 Strobing Brake
Light Pigtail is required. The secondary filament of the brake light assembly must be connected to a switch enabling its use as
a strobing rain light. A Strobing Brake Light Kit P/N 1168003 is available, which includes the brake light and pigtail."

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

In SRF, GCR section 9.1.8.D.1.H, add the following:
"NO MODIFICATIONS ALLOWED. Front brake ducts are required, attached to the openings in the lower radiator baffles, any
flexible 4" duct material allowed, installed length minimum 12" maximum 36" in length. Must be securely fastened, Bracket Part
# P/N 800368 can be used. Shall Must serve no other purpose. An extension may be welded to the side of the throttle pedal to
improve heel-and-toe braking. Master cylinder casting / location must be used as delivered on P/N 180110 Pedal Mounting
support. Aeroquip style -3 braided stainless flex lines only, must attach to all brake components without modification. Brake pad
"anti-rattle" clips must be removed."
In SRF, GCR section 9.1.8.D.1.V, add the following:
"ii. Rear SADEV shift cable aluminum two-piece style clamp may be used. The P/N WM302007A clamp must serve no other
purpose."
In SRF, GCR section 9.1.8.D.1.X.k, add the following:
"Negative camber shall must not exceed 5.0 degrees absolute maximum front and rear."
In SRF, GCR section 9.1.8.D.1.AA.b, add the following:
"2. Height of the radiator opening vertical surface 3 1/2“ +/- 1/2"."
P2 Engine Table B.1
2008 and older Stock
Suzuki, Yamaha,
Honda, BMW
38.5mm
P2 Engine Table B.2 Not required
P2 Engine Table B.3 38.5mm
Modified
Engine
950 lbs.
1005cc max
P2 Engine Table B.1
2008 and older 37mm
P2 Engine Table B.2 Not required
P2 Engine Table B.3 39mm
Stock Engine
1050 lbs.

In FF, GCR section 9.1.1.B.14.e.3.a, add the following:
"The standard ring pack, PN 13011-RB1-004 (Riken) or 13011-RB1-006 (Nippon), or the oversize ring pack, PN 13021-RB7-Z01
(Riken), or 13021-RB7-Z02 (Nippon), or FF800-100 (Fast Forward), may be used."

In P2 Engine Table, Spec Line B.1, add to notes as follows:
"No modifications allowed on engines manufactured after 2008 model year. 2007-2008 Suzuki GSX-R1000 crankcase part
#11300-21860 may be replaced with 2016-2019 Suzuki GSX-S1000 crankcase part #11301-04840."

In P2 Engine Table, Spec Line E, change the notes as follows:
"No engine modifications except for dry sump oil system, ECU mapping, and exhaust system the following: oil system, ECU, and
exhaust are unrestricted."

In P2 Table 1, FIA Group CN spec line, change the notes as follows:
"FIA Group CN homologated chassis, brake calipers and discs, hub carriers, and suspension components are required. V de
V European Proto Endurance Series Challenge permitted bodywork, rear diffuser, wing, wheels, and assisted
shifting are allowed. Car M must comply with all other P2 requirements. Competitors must have copies of FIA Group CN
Technical Regulations and V de V European Proto Endurance Series Challenge Sporting and Technical Regulations in their
possession and present them upon request are available here: https://www.scca.com/pages/technical-forms-and-downloads."

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used.
OR
Front – Hoosier P/N 46101 P185/65R13 W2
Rear – Hoosier P/N 46105 P205/60R13 W2
1. It is forbidden to regroove tires.
2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for
violation will be the loss of qualifying times and/or the disqualification of race results.
3. Hoosier SRF/SRF3 Decal Placement:
Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to
the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the
rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including
SCCA Enterprises."

In FE, GCR section 9.1.1.I.2.U.b.3, change as follows:
"Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure."
In SRF, GCR section 9.1.8.D.1.U.b.3, change as follows:
"Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure. Item 1 will be done by
the CSR or other shop that is equipped for this type of work and will be paid directly."

In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows:
"Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose
to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the
rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including
SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1)
decal must be located on each side of the car and one (1) decal must be visible on the front."

In FF, GCR section 9.1.1.B.14.r.1, change as follows:
"All emission control devices must be removed and blocked off by the blanking plate provided by HPD or Fast Forward as noted
below, except for the VTEC activation valve. The VTEC activation valve must be retained; and it must be functioning. No
modifications are permitted.
a. EGR Plate: Fast Forward PN: FF200-301.
b. EGR Port Cover: Fast Forward PN: FF200-302."

In SRF, GCR section 9.1.8.D.2.H.23, change as follows:
"Air Filter: P/N WM301020 or K&N RC-9160"

In SRF, GCR section 9.1.8.D.1.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with
no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."

In SRF, GCR section 9.1.8.D.2.B, change as follows:
"Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the
nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."

In FF, GCR section 9.1.1.B.20.A.3, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
In FC, GCR section 9.1.1.B.20.B.4, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."

In FF, GCR section 9.1.1.B.14.e.1, change as follows:
"Honda Fit OEM standard size pistons, PN: 13010-RB1-000, or Honda Fit OEM 0.25mm oversize pistons, PN: 13020-RB7-Z00, or
Fast Forward 0.25mm oversize pistons, PN: FF800-110, may be used."
In GCR section 9.1.1.B.14.e.2, change as follows:
"a. Maximum standard piston diameter, measured at a point 16mm from the bottom of the skirt: 73.240mm
(2.8834 2.8835 inches).
b. Centerline of wrist pin to crown maximum: 26.21mm (1.032 inches).
c. Maximum overall height from skirt to crown edge: 47.80mm (1.882 inches).
d. Minimum weight: 198.0 grams (6.984 ounces).
e. Minimum weight of piston pin: 66 grams (2.25 ounces).
f. Combined minimum weight of piston, piston pin and connecting rod: 543.5 grams (18.85 ounces).
g. Combined minimum weight of piston, wrist pin, and circlips: 267 grams (9.418 ounces).
h. Centerline of wrist pin to crown edge: 26.289mm (1.035 inches).
i. Ring groove widths:
Top ring groove: 1.003mm (0.0395 inches).
Middle ring groove: 1.016mm (0.0400 inches).
Oil ring groove: 1.981mm (0.0780 inches).
j. Ring groove distance from wrist pin center to bottom of groove:
Top ring groove: 19.63mm (0.7730 inches).
Middle ring groove: 15.29mm (0.6020 inches).
Oil ring groove: 10.91mm (0.4295 inches)."

In P2 Engine Table, Line E Note 2, add the following:
"8. Minimum weight 1335 lbs."

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Formula F shall be limited to the following tires (front tires may not be used as rears):
Dries:
Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13
Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13
Wets:
Front - Hoosier Wet or W3 Radial 44421 185/60R13
Rear - Hoosier Wet or W3 Radial 44426 205/60R13
Alternatively, Formula F cars with rocker arm suspension (e.g., Swift DB1, 1987-90 Reynard) and/or outboard suspension on at
least one chassis end may use the following tires:
Dries:
Front - Hoosier H43130 R60A 20.0 x 6.0-13 or H43164 R60A 20.5 x 7.0-13 bias ply slick
Rear – Hoosier H43307 R60A 22.5 x 7.2-13 bias ply slick
Wets:
Radial wets listed above
or
Front - Hoosier 44165 135/545-13 VFF
Rear - Hoosier 44170 165/580-13 VFF
Front tires may not be used as rears, and tires may not be mixed, i.e., radial tires may not be mixed with bias ply slick tires, bias
ply slick tires may not be mixed with VFF tires, and radial tires may not be mixed with VFF tires."

In SRF, GCR section 9.1.8.D.1.D, add the following:
"f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

In SRF, GCR section 9.1.8.D.2.K, change as follows:
"OR
SADEV-SRF3 6-Speed Sequential (beginning from Oct. 4, 2021 onward):
1st 12-36 3.0000 : 1
2nd 15-31 2.0667 : 1
3rd 18-28 1.5556 : 1
4th 22-28 1.2727 : 1
5th 24-26 1.0833 : 1
6th 25-23 0.9200 : 1
Final Drive Ratio: 15-48 3.20"

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Formula F shall be limited to the following tires (front tires may not be used as rears):
Dries:
Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13
Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13
Wets:
Front - Hoosier Wet or W3 Radial 44421 185/60R13
Rear - Hoosier Wet or W3 Radial 44426 205/60R13
Alternatively, Formula F cars with rocker arm suspension (e.g., Swift DB1, 1987-90 Reynard) and/or outboard suspension on at
least one chassis end may use the following tires:
Dries:
Front - Hoosier H43130 R60A 20.0 x 6.0-13 or H43164 R60A 20.5 x 7.0-13 bias ply slick
or
Hoosier 44165 135/545-13 VFF
Rear – Hoosier H43307 R60A 22.5 x 7.2-13 bias ply slick
or
Hoosier 44170 165/580-13 VFF
Wets:
Radial wets or VFF tires listed above
or
Front - Hoosier 44165 135/545-13 VFF
Rear - Hoosier 44170 165/580-13 VFF
Front tires may not be used as rears, and tires may not be mixed, i.e., radial tires may not be mixed with bias ply slick tires, bias
ply slick tires may not be mixed with VFF tires, and radial tires may not be mixed with VFF tires."

In SRF, GCR section 9.1.8.D.1.V.ff, change as follows:
"SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan
permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Alternatively, Formula F cars with rocker arm suspension (e.g., 1987-90 Reynard, Swift DB1,) and/or outboard suspension on at
least one chassis end homologated in 1989 or earlier with any combination of rocker arm or outboard suspension on all four
corners (e.g., 1987 – 1990 Reynard, Swift DB1) may use the following alternative tires. Note: This rule is intended to allow older
cars with the described suspension design to use the alternative tires. It is not to be exploited by modifying cars with push-rods or
pull-rods to meet the above requirements or by modifying either end of older cars to push- or pull-rod suspension to be eligible to
run the alternative tires. Cars that were homologated in 1989 or earlier with push- or pull-rod suspension on no more than two
corners may seek approval to run the alternative tire by utilizing the compliance process outlined in GCR section 8.1.4."

In SRF, GCR section 9.1.8.D.2.H.18, add the following:
"Spark Plugs: P/N G301041 ONLY NGK LTR7IX-11 / Washers or sealing rings are not allowed for any purpose."