FE + FM + P2 at Buttonwillow Raceway Park

2022-03-01 P2 Add spec line for Beasley B2

#32147 from Formula/Sports Racing Committee · Rule change · TB 22-03 (2022-03 Fastrack)

In P2 Table 1, add a spec line as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2022-03-01 P2 E&O Table 1 spec line wing terminology

#32148 from Formula/Sports Racing Committee · Rule change · TB 22-03 (2022-03 Fastrack)

In P2 Table 1, AMAC, Asteck, Cheetah, Decker, Fox, LeGrand, Converted F5 spec line, change the notes as follows:
"Wings up to 16.5in cord chord of single or dual element;"
In P2 Table 1, AMAC-AM5, Fox-2-Seater, Zephyrus, Decker 1/2 spec line, change the notes as follows:
"Wings up to 16.5in cord chord of single or dual element;"
In P2 Table 1, Bobsy spec line, change the notes as follows:
"Wings up to 16.5in cord chord of single or dual element only;"
In P2 Table 1, Jondal spec line, change the notes as follows:
"Wings up to 16.5in cord chord of single or dual element only;"

2022-03-01 P2 E&O class name

#32196 from Formula/Sports Racing Committee · Rule change · TB 22-03 (2022-03 Fastrack)

In P2 Table 1, AMAC, Asteck, Cheetah, Decker, Fox, LeGrand, Converted F5 cars spec line, change the marque as follows:
"AMAC, Asteck, Cheetah, Decker, Fox, LeGrand, Converted F500 cars see notes"
In P2 Table 1, AMAC, Asteck, Cheetah, Decker, Fox, LeGrand, Converted F5 cars spec line, change the notes as follows:
"Converted F500 cars must retain suspension compliant with F500 requirements and meet all P2 non-spec line requirements
except minimum width is 55 inches."

2022-04-01 P2 After Market to Aftermarket

#32373 from Club Racing Board · Rule change · TB 22-04 (2022-04 Fastrack)

In F500, GCR Section 9.1.1.D.15.D., change as follows:
"Stand-alone after market aftermarket ECUs are not permitted."
In P2, GCR Section 9.1.8.F.3.a., change as follows:
"As manufactured and ground by Oldsmobile or by an after after market aftermarket cam manufacturer to Oldsmobile factory
specifications for Vin.A (W41) or Mantapart #OP 1149."
In P2, GCR Section 9.1.8.F.3.b., change as follows:
"As manufactured and ground by Oldsmobile or by an after market aftermarket cam manufacturer to Oldsmobile factory profile
Vin. D or Mantapart #OP 1148."

2022-05-01 P2 E&O Clarification of Chassis Construction Requirements

#32469 from Club Racing Board · Rule change · TB 22-05 (2022-04 Fastrack)

In P2, GCR section 9.1.8.C.A.1, add the following:
"Chassis fully composed of composite structural materials or chassis partially composed of composite materials that is not
capable of rolling on its wheels without the composite materials being installed."
In P2, GCR section 9.1.8.C.C.1, add the following:
"Allow for any form of chassis construction except fully composite chassis. A chassis partially composed of composite materials
must satisfy the requirements of section 9.4.5.A, B, C, E, F and be capable of rolling on its wheels without the composite materials
being installed."

2022-05-01 P2 Clean up P2 wording

#32525 from Formula/Sports Racing Committee · Rule change · TB 22-05 (2022-04 Fastrack)

In P2, GCR section 9.1.8.C, change as follows:
"PROTOTYPE 2 (P2) CLASSIFICATION"
In GCR CONTENTS, change as follows:
"PROTOTYPE 2 (P2) CLASSIFICATION"

2022-06-01 FE Update FE/FE2 Tire Rule

#32613 from Robey Clark · Rule change · TB 22-06 (2022-06 Fastrack)

In FE, GCR section 9.1.1.I.2.M, change as follows:
"Tires must be run as delivered in sets of 4 as stated below:"

2022-06-01 FE Master cylinder clarification

#32669 from Club Racing Board · Rule change · TB 22-06 (2022-06 Fastrack)

In FE, GCR section 9.1.1.I.2.K.c, change as follows:
"Master cylinders must be the Girling type:
Girling F front master cylinder is .700" piston diameter, Part # WM802005
Girling R rear master cylinder is .750" piston diameter, Part # WM802006"

2022-09-01 FE Engine Heat Shield & Insulation

#33019 from Robey Clark · Rule change · TB 22-09 (2022-09 Fastrack)

In FE, GCR section 9.1.1.I.2.G.a.17, change as follows:
"A heat shield and heat insulation material may be used between the engine block and the exhaust system and is recommended
for the purpose of protecting hoses, shifter cable, and wiring from the heat of the engine and exhaust. Heat insulation material
may also be used to protect the fuel cell, fuel filter, fuel rail, and fuel lines."

2022-10-01 FE Brake bias adjuster clarification

#33084 from Robey Clark · Rule change · TB 22-10 (2022-10 Fastrack)

In FE, GCR section 9.1.1.I.2.K, add the following:
"f. Driver adjustable manual brake bias is allowed."

2022-10-01 FE FE Front and Rear Wing Update & Clarification

#33089 from Robey Clark · Rule change · TB 22-10 (2022-10 Fastrack)

In FE, GCR section 9.1.1.I.2.F.g, change as follows:
"The front wing main plane, front wing secondary elements, front wing support mounts, and front wing endplates assembly and
its related mounting components must be used and mounted as delivered from Enterprises. Any m Modifications to these parts,
except as specifically noted herein, is strictly forbidden are prohibited. The front main wing plane angle is zeroed on the rear
upper aft transmission surface measured with a suitable angle gauge, i.e.: digital level on the top main plane 2 inches outward
from the nose box mounts element may be adjusted +2.5 to -0.5 degrees. It must meet a minimum measurement of negative .5
degrees (angled down in the back) and a maximum measurement of positive 2.5 degrees (angled up in the back). It is acceptable
to shim the main plane to obtain this measurement. Shimming 2 of the 4 verticals through the main element mounting points to

2023-01-01 P2 Request to Classify Sebeco NP01

#33378 from Benjamin Cooper · Rule change · TB 23-01 (2023-01 Fastrack)

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)
Marque
Wheelbase inches
max/ Track Max
inches
Weight Displacement Engine Restrictor Notes

A specification table follows in the original; it is not shown here.

2023-01-01 P2 Radical spec line clarifications

#33485 from Jeff Barrow · Rule change · TB 23-01 (2023-01 Fastrack)

In P2 Table 1, Radical SR3/SR4 spec line, make the following change:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2023-01-01 P2 E&O original class intent

#33519 from Club Racing Board · Rule change · TB 23-01 (2023-01 Fastrack)

In P2, GCR section 9.1.8.A.1, change as follows:
"Chassis fully composed of composite structural materials or chassis partially composed of composite materials that is not
capable of rolling on its wheels without the composite materials being installed."
In P2, GCR section 9.1.8.C.C.1, change as follows:
"Allow for any form of chassis construction except fully composite chassis incorporating composite structural materials. A chassis
partially composed of composite materials must satisfy the requirements of section 9.4.5.A, B, C, E, F, and be capable of rolling
on its wheels without the composite materials being installed. Both tube frame and aluminum or steel monocoque chassis
construction are allowed.”

A specification table follows in the original; it is not shown here.

2023-01-01 P2 Update Engine Table Spec Line B.1

#33608 from Club Racing Board · Rule change · TB 23-01 (2023-01 Fastrack)

In P2 Engine Table, Spec Line B.1, change as follows:

2023-04-01 FE Update FE SADEV Transmission Rule

#33883 from Robey Clark · Rule change · TB 23-04 (2023-04 Fastrack)

In FE, GCR section 9.1.1.I.2.G.b.4.b, change as follows:
"(All SADEV ratios are under review and could be updated prior to sealing date)"

2023-04-01 P2 Remove redundant effective date language and update engine table

#34012 from Club Racing Board · Rule change · TB 23-04 (2023-04 Fastrack)

In P2 Engine Table, Spec Line B.1, change as follows:

2023-04-01 P2 E&O - Correct dimensional equivalents

#34038 from Club Racing Board · Rule change · TB 23-04 (2023-04 Fastrack)

In P2, GCR section 9.1.8.C.D.2, change as follows:
"Height: No part of the vehicle having special or significant aerodynamic function shall exceed a height of 115cm (45.275 inches)
above the ground with the car in normal racing trim, driver aboard."
In P2, GCR section 9.1.8.C.D.3, change as follows:
"However, no portion shall extend more than 10cm (3.937 inches) beyond a plane tangent to the outer face of the front and rear
wheels with tires."
P2 Engine Table
Spec

A specification table follows in the original; it is not shown here.

2023-05-01 P2 Clarify minimum side body height requirement

#34143 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

In P2, GCR section 9.1.8.C.D.6, change as follows:
"As viewed from the side, T the outermost surface of side pods body between the front and rear wheel openings and above the
floor must have a minimum height equal to the height of the front axle centerline."

2023-05-01 P2 Clarify closed cockpit single seat car allowance

#34144 from Club Racing Board · Rule change · TB 23-05 (2023-05 Fastrack)

In P2, GCR section 9.1.8.C.C, add a section as follows:
"4. Closed cockpit single seat cars are not permitted unless specifically allowed by a spec line in Table 1."

2023-12-01 P2 Correct Table 1 for Engine Date Range Specifications

#35182 from Formula/Sports Racing Committee · Rule change · TB 23-12 (2023-09 Fastrack)

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2024-01-01 FE Update FE Rain Light Rule

#34707 from Robey Clark · Rule change · TB 23-09 (2023-09 Fastrack)

In FE, GCR section 9.1.1.I.2.N.f, change as follows:
"Any rain light is allowed. Effective 1/1/2024, a rain light that meets FIA Standard 8874-2019, Technical List No. 76, is required as
specified in GCR section 9.3.32.B.2."

2024-01-01 P2 E&O - Clarify B.1 modified engine range in AMAC spec lines

#35225 from Club Racing Board · Rule change · TB 24-01 (2024-01 Fastrack)

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

2024-01-01 FE FE/FE2 rule update

#35269 from Robey Clark · Rule change · TB 24-01 (2024-01 Fastrack)

In FE, GCR section 9.1.1.I.2.P.c, add the following:
"Racer's tape may be used to repair crash damage, or as a precautionary means of securing the body panels or
retaining latches fasteners only. Crash-damage is defined as having occurred during the current event, and the tape should be of
an appropriate color if possible. Taping of body seams is not allowed. Taping across heat exchanger openings as a way to control
temperature is allowed and may serve no other purpose."

2024-01-01 P2 Replacement Engine Crankcase for 07/08 Suzuki GSX-R1000 Engines

#35340 from Michael A Reupert · Rule change · TB 24-01 (2024-01 Fastrack)

In P2 Engine Table, Spec Line B.1, add to notes as follows:
"No modifications allowed on engines manufactured after 2008 model year. 2007-2008 Suzuki GSX-R1000 crankcase part
#11300-21860 may be replaced with 2016-2019 Suzuki GSX-S1000 crankcase part #11301-04840."

2024-05-01 P2 CN Spec ECU

#35835 from Bart Wolf · Rule change · TB 24-05 (2024-05 Fastrack)

In P2 Engine Table, Spec Line E, change the notes as follows:
"No engine modifications except for dry sump oil system, ECU mapping, and exhaust system the following: oil system, ECU, and
exhaust are unrestricted."

2024-05-01 P2 E&O - Correct FIA Group CN spec line notes

#35900 from Club Racing Board · Rule change · TB 24-05 (2024-05 Fastrack)

In P2 Table 1, FIA Group CN spec line, change the notes as follows:
"FIA Group CN homologated chassis, brake calipers and discs, hub carriers, and suspension components are required. V de
V European Proto Endurance Series Challenge permitted bodywork, rear diffuser, wing, wheels, and assisted
shifting are allowed. Car M must comply with all other P2 requirements. Competitors must have copies of FIA Group CN
Technical Regulations and V de V European Proto Endurance Series Challenge Sporting and Technical Regulations in their
possession and present them upon request are available here: https://www.scca.com/pages/technical-forms-and-downloads."

2024-08-01 FE Hoosier Tire Decal Placement

#36435 from Robey Clark · Rule change · TB 24-08 (2024-08 Fastrack)

In FE, GCR section 9.1.8.I.2.M, add the following:
"b. Hoosier FE/FE2 Decal Placement:
Five (5) "Hoosier" decals are required in the following locations: One (1) small "Hoosier" decal on the nose or the front shock
cover of the car. One (1) 12" "Hoosier" decal on the outside vertical plane of each front wing plate. One (1) 12" "Hoosier" decal
on the vertical plane of each of the lower floor panels just in front of the rear wheels. Hoosier decals are available, free of charge,
from all Hoosier tire distributors and SCCA Enterprises."

2024-09-01 FE Protest Fee Clarification

#36540 from SCCA Staff · Rule change · TB 24-09 (2024-09 Fastrack)

In FE, GCR section 9.1.1.I.2.U.b.3, change as follows:
"Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure."
In SRF, GCR section 9.1.8.D.1.U.b.3, change as follows:
"Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure. Item 1 will be done by
the CSR or other shop that is equipped for this type of work and will be paid directly."

2024-09-01 FE Update on Letter 36620 with new Hoosier Contingency Decal Info

#36625 from Robey Clark · Rule change · TB 24-09 (2024-09 Fastrack)

In FE, GCR section 9.1.1.I.2.M.b, change as follows:
"Five (5) "Hoosier" decals are required in the following locations: One (1) small "Hoosier" decal on the nose or the front shock
cover of the car. One (1) 12" "Hoosier" decal on the outside vertical plane of each front wing plate. One (1) 12" "Hoosier" decal
on the vertical plane of each of the lower floor panels just in front of the rear wheels. Hoosier decals are available, free of
charge, from all Hoosier tire distributors and SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to
qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the
front."

2024-12-01 FE Brake Line to A-Arm Covers

#37110 from Robey Clark · Rule change · TB 24-12 (2024-12 Fastrack)

In FE, GCR section 9.1.1.G.2.K, add the following:
"g. If used, SCCA Enterprises Part # WM803010 Brake Line to Control Arm covers must be used as delivered and must be securely
fastened with zip ties/tie straps or tape. Part # WM803010 is the only approved part and may serve no other purpose."

2024-12-01 P2 2000 cc Pinto Engine Car Weight

#37187 from Marvin Hodges · Rule change · TB 24-12 (2024-12 Fastrack)

In P2 Engine Table, Line E Note 2, add the following:
"8. Minimum weight 1335 lbs."

2025-09-01 FE FE & FE2 Rule Updates

#38901 from Robey Clark · Rule change · TB 25-09 (2025-09 Fastrack)

Effective 9/1/25 in FE, GCR section 9.1.1.G.1.A, change as follows:
"Definition
FE’s with the Mazda 2.0L MZR engine will be classed as “FE2” and will use the class designation FE2. The Mazda 2.0L MZR motor
can be used in all SCCA events. It shall run under all FE Preparation rules except as noted below:
a. 2.0L MZR may be run with an Elite 5SPD or a Complete SADEV 6SPD transmission Kit
Must use the following:
b. 2.0L only Intake Manifold Part # WM30106
c. Throttle Body Part # WM591930-Jenvey

A specification table follows in the original; it is not shown here.

2025-10-01 FE FE & FE2 Bubble Tail

#38978 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)

In FE, GCR section 9.1.1.G.2.F.k, change as follows:
"Enterprises bubble tail P/N: WM138014 is allowed for FE and is the only configuration for FE2."

2026-01-01 FE FE & FE2 Rule Updates

#39484 from Robey Clark · Rule change · TB 26-01 (2026-01 Fastrack)

In FE, GCR section 9.1.1.G.2.G.a.1, add the following:
"NO MODIFICATIONS ARE ALLOWED EXCEPT WHERE SPECIFICALLY AUTHORIZED WITHIN THESE RULES. This includes all fuel
injection and engine management components, including exhaust, cooling, electrical and lubrication systems. All systems are
subject to test procedures and must conform to OEM / SCCA Enterprises specifications as stated and supplied by Enterprises. All
fluids, except fuel, are unrestricted."
In FE, GCR section 9.1.1.G.2.T, add the following:
"If a competitor refuses to give their engine and/or unlabeled parts for testing per a request of the Class Compliance Chief (CCC)
or Chief Steward, the following penalties will automatically be imposed:"