F5 + FM + P2 at Buttonwillow Raceway Park

In P2 Table 1, add a spec line as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

In P2 Table 1, AMAC, Asteck, Cheetah, Decker, Fox, LeGrand, Converted F5 spec line, change the notes as follows:
"Wings up to 16.5in cord chord of single or dual element;"
In P2 Table 1, AMAC-AM5, Fox-2-Seater, Zephyrus, Decker 1/2 spec line, change the notes as follows:
"Wings up to 16.5in cord chord of single or dual element;"
In P2 Table 1, Bobsy spec line, change the notes as follows:
"Wings up to 16.5in cord chord of single or dual element only;"
In P2 Table 1, Jondal spec line, change the notes as follows:
"Wings up to 16.5in cord chord of single or dual element only;"

In F500, GCR section 9.1.1.D.19, change as follows:
"All F500 cars competing in Majors Races and the Runoffs must have the AIM part #X47KPFSOLO2R0 data box mount installed
on the vehicle to provide the necessary mounting of the AIM Solo or Solo 2 data box."

In P2 Table 1, AMAC, Asteck, Cheetah, Decker, Fox, LeGrand, Converted F5 cars spec line, change the marque as follows:
"AMAC, Asteck, Cheetah, Decker, Fox, LeGrand, Converted F500 cars see notes"
In P2 Table 1, AMAC, Asteck, Cheetah, Decker, Fox, LeGrand, Converted F5 cars spec line, change the notes as follows:
"Converted F500 cars must retain suspension compliant with F500 requirements and meet all P2 non-spec line requirements
except minimum width is 55 inches."

In F500, GCR Section 9.1.1.D.15.D., change as follows:
"Stand-alone after market aftermarket ECUs are not permitted."
In P2, GCR Section 9.1.8.F.3.a., change as follows:
"As manufactured and ground by Oldsmobile or by an after after market aftermarket cam manufacturer to Oldsmobile factory
specifications for Vin.A (W41) or Mantapart #OP 1149."
In P2, GCR Section 9.1.8.F.3.b., change as follows:
"As manufactured and ground by Oldsmobile or by an after market aftermarket cam manufacturer to Oldsmobile factory profile
Vin. D or Mantapart #OP 1148."

In P2, GCR section 9.1.8.C.A.1, add the following:
"Chassis fully composed of composite structural materials or chassis partially composed of composite materials that is not
capable of rolling on its wheels without the composite materials being installed."
In P2, GCR section 9.1.8.C.C.1, add the following:
"Allow for any form of chassis construction except fully composite chassis. A chassis partially composed of composite materials
must satisfy the requirements of section 9.4.5.A, B, C, E, F and be capable of rolling on its wheels without the composite materials
being installed."

In P2, GCR section 9.1.8.C, change as follows:
"PROTOTYPE 2 (P2) CLASSIFICATION"
In GCR CONTENTS, change as follows:
"PROTOTYPE 2 (P2) CLASSIFICATION"

In F500, GCR section 9.1.1.D.14.A, change as follows:
"Carburetor mounting shall must be of individual runners, with no balance pipes, and no plenums unless fitted as standard as on
the Rotax 493 and 593 engines. The use of the intake plenum/resonator on the 493 and the 593 engines is optional. If the intake
resonator is removed the resulting holes MUST be completely plugged and the plugs must be held in place by appropriate
clamps. Plugs may be of any material and must serve no other purpose than to plug the holes originally intended for the
resonator. 38mm intake boots, BPP 420867860 (last 6 digits 867860 are embossed on the boot), BPP 420867862 (last 6 digits
867862 are embossed on the boot), or Kimpex 07-100-33, or Moto Tassinari V-Force 3 Reed Valve System V3124-873B-
2 shall must be used for the 493 and 593 non-HO engines. 38mm intake boots, BPP 420867882 (last 6 digits 867882 are
embossed on the boot) or Moto Tassinari V-Force 3 Reed Valve System V3124-873B-2 shall must be used for the 2003 593 HO
engine, and 38mm intake boots, BPP 420867879 (last 6 digits 867879 are embossed on the boot) or Moto Tassinari V-Force 3
Reed Valve System V3124-873B-2 shall must be used for the 2004-2007 593 HO engines. Supercharging, turbocharging, and
direct fuel injection are prohibited."
In F500, GCR section 9.1.1.D.14, add a new section as follows:
"M. The stock oil injection pump, oil lines, and control cables may be removed from all Rotax engines. The oil injection ports may
be removed and plugged as necessary."

In F500, GCR section 9.1.1.D.15.G, add the following:
"The exhaust system and exhaust manifold are unrestricted, within SCCA safety regulations, except that
stepped diameter exhaust headers are not allowed. This prohibition does not include the exhaust flange area immediately
adjacent to the cylinder head."
In F500 Engine Table, Honda CBR600RR, Suzuki GSXR600, and Yamaha R6 spec lines, add the following:
"Stepped diameter exhaust headers are not allowed"

In F500, GCR section 9.1.1.D.14, add a new section as follows:
"N. Alternate ECU for Rotax engines: The use of the Ingi Tech Sparker ignition part number DCP-CDI-P2 is permitted."

In F500, GCR section 9.1.1.D.14.A, change as follows:
“Carburetor mounting must be of individual runners, with no balance pipes and no plenums unless fitted as standard as on the
Rotax 493 and 593 engines. The use of the intake plenum/resonator on the 493 and 593 engines is optional. If the intake
resonator is removed the resulting holes MUST be completely plugged and the plugs must be held in place by appropriate
clamps. Plugs may be of any material and must serve no other purpose than to plug the holes originally intended for the
resonator. 38mm i Intake boots, BPP 420867860 (last 6 digits 867860 are embossed on the boot), BPP 420867862 1 (last 6 digits
867862 1 are embossed on the boot), or Kimpex 07-100-33, or Moto Tassinari V-Force 3 Reed Valve System V3124-873B-2 must
be used for the 493 and 593 non-HO engines. Moto Tassinari V-Force V3120-794A-2 Reed Valve System may be used with any
allowed intake boot on the 493 and 593 non-HO engines. 38mm i Intake boots, BPP 420867882 (last 6 digits 867882 are
embossed on the boot) or Moto Tassinari V-Force 3 Reed Valve System V3124-873B-2 must be used for the 2003 593 HO engine,
and 38mm i ntake boots, BPP 420867879 (last 6 digits 867879 are embossed on the boot) or Moto Tassinari V-Force 3 Reed Valve
System V3124-873B-2 must be used for the 2004-2007 593 HO engines. Supercharging, turbocharging, and direct fuel injection
are prohibited.”

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)
Marque
Wheelbase inches
max/ Track Max
inches
Weight Displacement Engine Restrictor Notes

A specification table follows in the original; it is not shown here.

In P2 Table 1, Radical SR3/SR4 spec line, make the following change:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

In P2, GCR section 9.1.8.A.1, change as follows:
"Chassis fully composed of composite structural materials or chassis partially composed of composite materials that is not
capable of rolling on its wheels without the composite materials being installed."
In P2, GCR section 9.1.8.C.C.1, change as follows:
"Allow for any form of chassis construction except fully composite chassis incorporating composite structural materials. A chassis
partially composed of composite materials must satisfy the requirements of section 9.4.5.A, B, C, E, F, and be capable of rolling
on its wheels without the composite materials being installed. Both tube frame and aluminum or steel monocoque chassis
construction are allowed.”
In P2, GCR section 9.1.8.C.2, change as follows:
"Anti-intrusion panels are allowed anywhere on the sides of the chassis. Materials and attachment
are is unrestricted. Attachment points must be at least 15cm (5.906 inches) apart center to center using fasteners no larger than
6.5mm (0.256 inches) diameter.”
In P2 Table 1, add the following:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

In P2 Engine Table, Spec Line B.1, change as follows:

In P2, GCR section 9.1.8.C.D.2, change as follows:
"Height: No part of the vehicle having special or significant aerodynamic function shall exceed a height of 115cm (45.275 inches)
above the ground with the car in normal racing trim, driver aboard."
In P2, GCR section 9.1.8.C.D.3, change as follows:
"However, no portion shall extend more than 10cm (3.937 inches) beyond a plane tangent to the outer face of the front and rear
wheels with tires."
P2 Engine Table
Spec
Line Engine Series

A specification table follows in the original; it is not shown here.

In P2, GCR section 9.1.8.C.D.6, change as follows:
"As viewed from the side, T the outermost surface of side pods body between the front and rear wheel openings and above the
floor must have a minimum height equal to the height of the front axle centerline."

In P2, GCR section 9.1.8.C.C, add a section as follows:
"4. Closed cockpit single seat cars are not permitted unless specifically allowed by a spec line in Table 1."

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

In P2 Table 1, change as follows:
P2 Table 1 (Spec Line Cars)

A specification table follows in the original; it is not shown here.

In P2 Engine Table, Spec Line B.1, add to notes as follows:
"No modifications allowed on engines manufactured after 2008 model year. 2007-2008 Suzuki GSX-R1000 crankcase part
#11300-21860 may be replaced with 2016-2019 Suzuki GSX-S1000 crankcase part #11301-04840."

In P2 Engine Table, Spec Line E, change the notes as follows:
"No engine modifications except for dry sump oil system, ECU mapping, and exhaust system the following: oil system, ECU, and
exhaust are unrestricted."

In P2 Table 1, FIA Group CN spec line, change the notes as follows:
"FIA Group CN homologated chassis, brake calipers and discs, hub carriers, and suspension components are required. V de
V European Proto Endurance Series Challenge permitted bodywork, rear diffuser, wing, wheels, and assisted
shifting are allowed. Car M must comply with all other P2 requirements. Competitors must have copies of FIA Group CN
Technical Regulations and V de V European Proto Endurance Series Challenge Sporting and Technical Regulations in their
possession and present them upon request are available here: https://www.scca.com/pages/technical-forms-and-downloads."

In P2 Engine Table, Line E Note 2, add the following:
"8. Minimum weight 1335 lbs."