AS + SRF + T4 at Michelin Raceway Road Atlanta

2023-04-01 T4 Request to Classify 2004-2008 Acura TSX in T4

#33590 from William Phee · Rule change · TB 23-04 (2023-04 Fastrack)

In T4 Spec lines, classify Acura TSX (2004-2008) as follows:

A specification table follows in the original; it is not shown here.

2023-04-01 T4 T4 Mustang Brakes/Swaybar

#34036 from Scotty B White · Rule change · TB 23-04 (2023-04 Fastrack)

In T4 Spec Lines, Ford Mustang (2005-2010), change Notes as follows:
"Any sway bar up to F: 35mm and R: 22mm 28mm permitted."

Applies to Ford Mustang on this page: Scotty B White, Paolo Salvatore

2023-05-01 SRF Update SRF Front W2 Rain Tire Part Number

#34118 from Robey Clark · Rule change · TB 23-05 (2023-05 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Front – Hoosier P/N 46100 1 P185/65R13 W2"

2023-06-01 T4 05-06 Mini Wheel Weight

#34112 from Mav Singh · Rule change · TB 23-06 (2023-05 Fastrack)

In T4 Spec Lines, Mini Cooper S (02-04), change as follows:
Wheel Size: "16 x 7 17 x 8"
Add to Notes: "Wheels conforming to B-spec rules are permitted."
In T4 Spec Lines, Mini Cooper S (05-06), change as follows:
Wheel Size: "16 x 7 17 x 8"
Add to Notes: "Wheels conforming to B-spec rules are permitted."
In T4 Spec Lines, Mini Cooper S (07-13), change as follows:
Wheel Size: "17 x 7 8"

2023-06-01 T4 06-09 VW Rabbit

#34153 from Cameron Conover · Rule change · TB 23-06 (2023-05 Fastrack)

In T4 Spec Lines, delete Volkswagen Rabbit 2.5 (06-07) in its entirety and change Volkswagen Rabbit 2.5 (08-09) as follows:
"Volkswagen Rabbit 2.5 (08 06-09)"
Add to Notes: "Integrated Engineering intake IEIMVB1-BK allowed with 25lb penalty."

2023-06-01 SRF Hoosier SRF Wet Front Tire Rule Update

#34189 from Robey Clark · Rule change · TB 23-06 (2023-06 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5" with driver as raced when P185/60R13 (H20 or W2) tires are used."

2023-06-01 T4 96-01 Audi a4 2.8 Spring Rate

#34217 from Michael Gordhamer · Rule change · TB 23-06 (2023-05 Fastrack)

In T4 Spec Lines, Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05), change as follows:
Wheel Size: "16 x 7 17 x 8"
Tire Size: "225 245"
Notes: "The following items must remain stock: shock/struts (including mounts), original wheels, and transmission differential -
unless specified below. 800lb springs allowed. Front and rear sway bars permitted 32mm max."

2023-07-01 T4 2002-2006 Mini Cooper S R53 Spec Line Request

#34336 from Aaron Fitzsimmons · Rule change · TB 23-06 (2023-07 Fastrack)

In T4 Spec Lines, Mini Cooper S (02-04), change Weight as follows:
"2750 2700"
In T4 Spec Lines, Mini Cooper S (05-06), change Weight as follows:
"2750 2700"

2023-08-01 AS Crate Motor Part Numbers

#32944 from Sam Daniels · Rule change · TB 23-08 (2023-08 Fastrack)

2023-08-01 AS Request wheel size change

#33007 from Michael Kamalian · Rule change · TB 23-08 (2023-08 Fastrack)

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2023-08-01 AS Alternative Upper Front Control Arms for Dodge Challenger

#33352 from Clark Cambern · Rule change · TB 23-08 (2023-08 Fastrack)

2023-08-01 AS Front Brake Caliper Adapters for Dodge Challenger

#33353 from Clark Cambern · Rule change · TB 23-08 (2023-08 Fastrack)

2023-08-01 T4 Rules Clarification for Mazda RX8 Spec Line

#34395 from Colin Koehler · Rule change · TB 23-08 (2023-08 Fastrack)

In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change notes as follows:
"Use of 2009 R3 transmission is permitted with alternate gear ratios as listed. R3 transmission must be paired with the listed
alternate final drive. Front sway bar permitted 32mm MAX rear sway bar 19 MAX, Front springs max 750, 500 rear. Cold air
intake permitted. Header permitted. Aftermarket flywheel and single disc clutch permitted with no weight penalty."
In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change notes as follows:
"Mazdaspeed radiator #0000-01-8501 allowed. Use of 2009 R3 transmission is permitted with alternate gear ratios as listed. R3
transmission must be paired with the listed alternate final drive. Mazdaspeed coil spring kit #QSEA-34-01Z allowed. 60mm flat
plate restrictor required. OE Rear spoiler allowed #F151-V4-920F. OE front air dam allowed #F151-V4-900f-BB. Springs Allowed:

2023-08-01 T4 rule book corrections

#34437 from Chi Ho · Rule change · TB 23-08 (2023-08 Fastrack)

In T3 Spec Lines, BMW 320i (14-15), add to Notes the following:
"Aftermarket intercooler permitted."
In T4 Spec Lines, BMW 320i (14-15), remove from Notes the following:
"Aftermarket intercooler permitted."

2023-08-01 T4 Ride Height Correction for the T3 Solstice.

#34615 from Joe Aquilante · Rule change · TB 23-08 (2023-08 Fastrack)

In T2 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), add to Notes the following:
"Minimum ride height is 3 inches."
In T3 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), add to Notes the following:
"Minimum ride height is 3 inches."

2023-09-01 T4 Inclusion of similar car. (CLK 320)

#34626 from Patrick Morgan · Rule change · TB 23-09 (2023-09 Fastrack)

In T4 Spec Lines, Mercedes Benz CLK 320 Coupe (2004), change as follows:
"Mercedes Benz CLK 320 Coupe, C320 Sedan (2004 2000-2007)

2023-10-01 SRF SRF Radiator Rule Update

#34805 from Robey Clark · Rule change · TB 23-10 (2023-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.V.j, change as follows:
"Radiator - Enterprises new style P/N 480465 (requires baffle P/N 480464) or P/N 480466 can be used. P/N 480466, may can be
replaced with Automotive P/N 1R698, CU698 or equivalent OEM manufacturer justified by one cross-reference chart equivalent,
as long as the size, shape, and material are the same as the original P/N. The capacity, core thickness, etc., cannot be changed
even if allowed under the above. The competitor is responsible for providing this documentation of the cross-reference P/N."

2024-01-01 T4 Mazda MX-5 ND1 Spec Line Request

#34232 from Josh Smith · Rule change · TB 24-01 (2024-01 Fastrack)

In T4 Spec Lines, Mazda MX-5 Miata/Club/ RF (16-18), change as follows:
Weight: "2650 2700"
Notes: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. The following item(s) must
remain stock: transmission differential unless specified below. Retractable hardtop option permitted but must be disabled from
moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette,
including Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r)
sway bars allowed. Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front springs
#0000-04-9700-08, rear springs #0000-04-9400-07, helper springs #0000-04-HLPR-EB (optional). Up to 500lb front and 300lb rear

2024-01-01 SRF Update SRF Rain / Brake Rule

#34706 from Robey Clark · Rule change · TB 23-09 (2023-09 Fastrack)

In SRF, GCR section 9.1.8.D.1.W.l, change as follows:
"A Super Bright LEDs Inc. rain / brake light comprised of a single standard trailer oval lamp, 2-1/4 inches x 6-1/2 inches, with
incandescent or LED illumination, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes
GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the
wiring harness. The secondary filament of the brake light assembly shall must be connected to a switch enabling its use as a rain
light."

2024-01-01 SRF Update SRF Brake Light Rule v1

#34853 from Robey Clark · Rule change · TB 23-10 (2023-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.W.l, change as follows:
"A Super Bright LEDs Inc. P/N PT-STRB-R24 (SCCA Enterprises P/N 180427A) rain / brake light, P/N PT-STRB-R24, is required in the
original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No
changes may be made to the original 3-pin connector on the wiring harness. An SCCA Enterprises P/N 1190503 Strobing Brake
Light Pigtail is required. The secondary filament of the brake light assembly must be connected to a switch enabling its use as
a strobing rain light. A Strobing Brake Light Kit P/N 1168003 is available, which includes the brake light and pigtail."

2024-01-01 T4 BRZ/FRS/86 Spring Allowance

#35038 from Luis Goncalves · Rule change · TB 24-01 (2024-01 Fastrack)

In T4 Spec Lines, Scion FR-S/10 series (13-16), change Notes as follows:
"Eibach 82105.320, 4.10582 and SPC 67660 allowed. Eibach 82105.320 sway bar kit allowed. Eibach 4.10582 springs or 225 lb (f)
and 300 lb (r) springs allowed. SPC 67660 allowed. Front strut tower brace allowed. Raceseng, part # raceseng-ft86-r-shock-top
permitted. Non-OEM limited slip differential allowed with +50 lbs. weight penalty. 55mm flat plate restrictor required. Only 17”
wheels permitted."
In T4 Spec Lines, Subaru BRZ/ BRZ Limited (13-16), change Notes as follows:
"Eibach 82105.320, 4.10582 and SPC 67660 allowed. Eibach 82105.320 sway bar kit allowed. Eibach 4.10582 springs or 225 lb (f)
and 300 lb (r) springs allowed. SPC 67660 allowed. Front strut tower brace allowed. Raceseng, part # raceseng-ft86-r-shock-top

Applies to Subaru BRZ on this page: Angelica Sprehe

2024-01-01 T4 TSX Allowance

#35219 from Oscar Jackson · Rule change · TB 24-01 (2024-01 Fastrack)

In T4 Spec Lines, Acura TSX (2004-2008), add to Notes the following:
"Header allowed."

2024-01-01 T4 Requested Update of Model Years of 370Z

#35231 from Richard Kulach · Rule change · TB 24-01 (2024-01 Fastrack)

In T3 Spec Lines, Nissan 370Z (09-16) / 370Z NISMO Edition (09-13), change model as follows:
"Nissan 370Z (09-16) / 370Z NISMO Edition (09-13) ,incl. Nismo (2009-2022)"

2024-01-01 SRF SRF / SRF3 Rule Updates

#35268 from Robey Clark · Rule change · TB 24-01 (2024-01 Fastrack)

In SRF, GCR section 9.1.8.D.1.H, add the following:
"NO MODIFICATIONS ALLOWED. Front brake ducts are required, attached to the openings in the lower radiator baffles, any
flexible 4" duct material allowed, installed length minimum 12" maximum 36" in length. Must be securely fastened, Bracket Part
# P/N 800368 can be used. Shall Must serve no other purpose. An extension may be welded to the side of the throttle pedal to
improve heel-and-toe braking. Master cylinder casting / location must be used as delivered on P/N 180110 Pedal Mounting
support. Aeroquip style -3 braided stainless flex lines only, must attach to all brake components without modification. Brake pad
"anti-rattle" clips must be removed."
In SRF, GCR section 9.1.8.D.1.V, add the following:

2024-02-01 T4 More Car Lightening Stuff

#35319 from Scotty B White · Rule change · TB 24-02 (2024-02 Fastrack)

In GCR, Section 9.1.9.2.D.1.g.3., change as follows:
"Batteries may be replaced provided the replacement is capable of starting the car. Batteries may not be relocated
unless noted on the spec line. Batteries must be adequately secured. Battery labeling must conform to 9.3.35.D. with
those of an alternate manufacturer, provided they are of similar amp-hour capacity, size and within 10% of OEM
weight."

2024-02-01 T4 ND Missed Items

#35352 from Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)

In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), add to Notes the following:
"3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-
02, 0000-02-5804-01)."
In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-21), add to Notes the following:
"3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-
02, 0000-02-5804-01)."

Applies to Mazda Miata on this page: Jonathan Neudorf, Ethan Barker, Charles Habisreutinger, Ayden Rose

Applies to Mazda MX-5 on this page: Marc Cefalo, Robert Spence, Kevin Fryer, Richard Mooney, Sergio Zlobin

2024-02-01 T4 Inclusion of B-C spec cars in T4

#35374 from Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)

In GCR, Section 9.1.9.2., change as follows:
"Touring car eligibility: Cars are eligible for the class they are listed with a specification line and with the specific
allowances permitted. In addition, T2-T4 cars may race one class up in touring classes above their specification line class
as long as they are a legal T2-T4 car and conform to their specification line allowances as classified. Cars conforming to
C-Spec rules are permitted to compete in Touring 4."

2024-02-01 T4 T2-T4 Set expiration dates on spec lines

#35378 from Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)

In T2-T4 Spec Lines, add **This Spec line will expire 12/31/24, Please submit to appeal**
to Notes to the following Spec Lines:
T2:
Acura TL SHAWD (10-13)
Audi S4 (12-14)
Audi S5 (13-14)
Audi TT RS (2018-)
Cadillac ATS-V (16-17)

2024-03-01 AS Request to Classify 1970-1981 Camaro and Firebird in AS

#33659 from Brandon Vivian · Rule change · TB 24-03 (2024-03 Fastrack)

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

2024-03-01 AS Fuel Cell 12

#34194 from Clark Cambern · Rule change · TB 24-03 (2024-03 Fastrack)

2024-03-01 T4 Reorganize Spec Lines

#35375 from Touring Committee · Rule change · TB 24-03 (2024-03 Fastrack)

In T2-T4 Spec Lines, change Spec Line as follows:
"Wheel- base (mm) Required Restrictor"

2024-03-01 T4 Allow any 400lb rear spring in the RX8

#35433 from Raymond Blethen · Rule change · TB 24-03 (2024-03 Fastrack)

In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change Notes as follows:
"Mazda Motorsports- 0000- 04-9700-08 or Eibach- 0800.250.0700 (R) Mazda Motorsports- 0000-04-9400-07 or Eibach
0700.250.0400, and helper 0000-04-9926 allowed. Springs allowed 700lb (f), 400(r)."

2024-03-01 AS Please Classify the 6th Gen Into AS.

#35448 from Daniel Richardson · Rule change · TB 24-03 (2024-03 Fastrack)

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

2024-03-01 T4 370Z Brake Rotor Size Correction

#35487 from Derek Chan · Rule change · TB 24-03 (2024-03 Fastrack)

In T2 Spec Lines, Nissan 370Z (09-17) / 370Z NISMO Edition (09-17), change Brakes (mm) as follows:
"(F)320 x 28 Vented R)320 x 16 Vented : (F) 355x32mm Vented(R) 350x20mm Vented”
In T3 Spec Lines, Nissan 370Z, incl. Nismo (2009-2022), change Brakes (mm) as follows:
"(F)320 x 28 Vented (R)320 x 16 Vented : (F) 355x32mm Vented(R) 350x20mm Vented”

2024-03-01 AS spec lines

#35713 from American Sedan Committee · Rule change · TB 24-03 (2024-03 Fastrack)

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2024-04-01 AS Restricted Prep Aftermarket Parts Request

#35682 from Tom Aquilante · Rule change · TB 24-04 (2024-04 Fastrack)

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

2024-04-01 T4 Corrections to T4 RX8 Spec line

#35767 from Touring Committee · Rule change · TB 24-04 (2024-04 Fastrack)

In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change Notes as follows:
"Mazdaspeed radiator #0000-01-8501 allowed. Mazdaspeed coil spring kit #QSEA-34-01Z allowed. OE Rear spoiler allowed
#F151-V4-920F. OE front air dam allowed #F151-V4-900f-BB. Springs allowed 700lb (f) max, 400(r) max. Oil metering pump may
be bypassed. Alternate sway bars allowed max 32mm (f) 19mm (r)."

2024-04-01 AS Allowance of 11

#35824 from American Sedan Committee · Rule change · TB 24-04 (2024-04 Fastrack)

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2024-05-01 AS 6th gen Camaro limited prep

#35733 from American Sedan Committee · Rule change · TB 24-05 (2024-05 Fastrack)

2024-05-01 T4 Allow T4 and T3 RX8 to Disable/Remove Factory Oil Inj.

#35761 from David Mead · Rule change · TB 24-05 (2024-05 Fastrack)

In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows:
"OEM oil injection system may be removed or disabled."
In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows:
"OEM oil injection system may be removed or disabled."

2024-05-01 AS Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V8 LS1 Alum BLK

#35825 from Desi Colon · Rule change · TB 24-05 (2024-05 Fastrack)

2024-05-01 T4 2023 ND2 Miata Classification and Allowances

#35837 from Coyote Black · Rule change · TB 24-05 (2024-05 Fastrack)

In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-21), change Year as follows:
"(19-21 24)"
In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-21), add to Notes as follows:
"Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front springs #0000-04-9700-
08, springs up to 500lb front and 300lb rear allowed. Mazda tower brace 0000-04-5626 allowed."

2024-05-01 T4 Errors and Omissions for 06-09 VW Rabbit Rotor

#35851 from Andrew Burke · Rule change · TB 24-05 (2024-05 Fastrack)

In T4 Spec Lines, Volkswagen Rabbit 2.5 (06-09), change Brakes as follows:
"(F) 228 288 Vented Disc (R) 260 Solid Disc"

2024-05-01 AS Full Prep Head

#35891 from American Sedan Committee · Rule change · TB 24-05 (2024-05 Fastrack)

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2024-05-01 T4 Driveshafts

#35916 from Scotty B White · Rule change · TB 24-05 (2024-05 Fastrack)

In GCR Section 9.1.9.2.D.4.b., add the following:
"6. T2-T3- Driveshafts may be replaced with alternative materials ie. carbon fiber, aluminum, steel. Two-piece driveshafts may
be replaced with one-piece units. If non-OEM driveshaft is used, add 25 lbs."

2024-05-01 T4 GCR ERROR - letter not properly applied to GCR

#35999 from Touring Committee · Rule change · TB 24-05 (2024-05 Fastrack)

In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), change Notes as follows:
"Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. The following item(s) must remain
stock: transmission differential unless specified below. Retractable hardtop option permitted but must be disabled from moving
action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including
Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars
allowed. Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front springs #0000-
04-9700-08, rear springs #0000-04-9400-07, helper springs #0000-04-HLPR-EB (optional). Up to 500lb front and 300lb rear
springs allowed. Mazda Motorsports Header part #0000-06-5410 allowed. Mazda tower brace 0000-04-5626 allowed."

Applies to Mazda Miata on this page: Jonathan Neudorf, Ethan Barker, Charles Habisreutinger, Ayden Rose

Applies to Mazda MX-5 on this page: Marc Cefalo, Robert Spence, Kevin Fryer, Richard Mooney, Sergio Zlobin

2024-06-01 AS Request for Classification of 2018-2023 mustang In

#35764 from Michael Kamalian · Rule change · TB 24-06 (2024-06 Fastrack)

2024-06-01 T4 Allow OEM Front Spoiler 06-08 Miata in T4

#35941 from David Mead · Rule change · TB 24-06 (2024-06 Fastrack)

In T4 Spec Lines, Mazda MX-5 / Club Model (06-15), add to Notes the following: "Front
spoiler permitted (NF51-V4-900F)."

Applies to Mazda MX-5 on this page: Marc Cefalo, Robert Spence, Kevin Fryer, Richard Mooney, Sergio Zlobin

2024-06-01 T4 T4 Mustang Weight Reduction In T4 Spec

#36051 from Scotty B White · Rule change · TB 24-06 (2024-06 Fastrack)

Lines, Ford Mustang V6 (05-10), change as follows:
Weight: "3275 3225"
Notes: "14” Brembo Brake Kit#M-2300-S permitted."

2024-06-01 T4 R53 Mini Cooper S spec line request In

#36056 from Manvinder Singh · Rule change · TB 24-06 (2024-06 Fastrack)

T4 Spec Lines, Mini Cooper S (02-04), add to Notes the following:
"Milltek exhaust manifold #SSXM459 allowed. 25mm rear sway bar allowed."
T4 Spec Lines, Mini Cooper S (05-06), add to Notes the following:
"Milltek exhaust manifold #SSXM459 allowed. 25mm rear sway bar allowed."

2024-07-01 T4 Mustang T2/T3

#35877 from Scotty B White · Rule change · TB 24-07 (2024-07 Fastrack)

In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), add to Notes as follows:
"Track/Performance Package parts permitted."
In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows:
"Track/Performance Package parts permitted."
In T3 Spec Lines, Ford Mustang V6 (15-17), change Notes as follows:
"Track/Performance package allowed."

2024-07-01 T4 Homologation of car to T4

#36030 from Patrick E Morgan · Rule change · TB 24-07 (2024-07 Fastrack)

In T4 Spec Lines, Mercedes C300 4Matic (2008-2011), classify as follows:

A specification table follows in the original; it is not shown here.

2024-07-01 T4 T2-T4 Driveshaft Mistake...?

#36050 from Scotty B White · Rule change · TB 24-07 (2024-07 Fastrack)

In GCR Section 9.1.9.2.D.4.b.6., remove as follows:
"If non-OEM driveshaft is used, add 25 lbs."
In T2 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows:
"Driveshaft from Alternate metallic driveshaft is allowed."
In T2 Spec Lines, Ford Mustang Boss 302 (12-13), change Notes as follows:
"Alternate metallic driveshaft is allowed."
In T2 Spec Lines, Ford Mustang GT 5.0L (11-14)ki, change Notes as follows:
"Alternate metallic driveshaft is allowed."

2024-07-01 T4 MINI Cooper S Spec Lines Corrections.

#36086 from David Oliveira · Rule change · TB 24-07 (2024-07 Fastrack)

In T4 Spec Lines, Mini Cooper S (02-04), delete spec line in its entirety.
In T4 Spec Lines, Mini Cooper S (05-06), change Model as follows:
"Mini Cooper S R53 (0205-06)"
In T4 Spec Lines, Mini Cooper S (07-13), change Model and Notes as follows:
"Mini Cooper S R56 (07-13)"
Notes: "The following items must remain stock: shock/struts (including mounts), original wheels, and transmission
differential - unless specified below. Convertible model not allowed. Factory optional limited slip differential allowed.
JCW struts (F) 31 31 6 768 410 (R)33 52 6 768 412, springs (F)31 33 6 768 415 (R)33 53 6 768 418. May de-camber

2024-07-01 T4 Allow Removal of Sound Tubes

#36130 from Coyote Black · Rule change · TB 24-07 (2024-07 Fastrack)

In GCR Section 9.1.9.2.D.1.b., add the following:
"2. OEM intake- Chambers, resonators and acoustic devices may be removed, provided; that their ports are located
prior to any required restrictor, their ports are completely sealed, and that the part serves no other purpose."

2024-07-01 T4 B8/8.5 Audi S4 T3 and T2

#36195 from Brian Leib · Rule change · TB 24-07 (2024-07 Fastrack)

In T3 Spec Lines, Classify Audi S4 (2000-2002) as follows and allow the T2 spec line to expire.

A specification table follows in the original; it is not shown here.

2024-08-01 T4 T4 Camaro V6 weight reduction

#36232 from Ted Warning · Rule change · TB 24-08 (2024-08 Fastrack)

In T4 Spec Lines, Chevrolet Camaro V-6 (96-02), change weight as follows:
"3250 3150"

2024-08-01 T4 BOP adjustment for ND MX5s

#36345 from Touring Committee · Rule change · TB 24-08 (2024-08 Fastrack)

In T4 Spec Lines, change Weight (lbs) as follows:
Mazda MX-5 Miata/Club (16-18): "2700 2650"
Mazda MX5 Miata/Club/ RF (19-24): "2800 2750"

2024-08-01 SRF Update Rain Tire Rule and Hoosier Decal Placement

#36436 from Robey Clark · Rule change · TB 24-08 (2024-08 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used.
OR
Front – Hoosier P/N 46101 P185/65R13 W2
Rear – Hoosier P/N 46105 P205/60R13 W2

2024-09-01 SRF Protest Fee Clarification

#36540 from SCCA Staff · Rule change · TB 24-09 (2024-09 Fastrack)

2024-09-01 SRF Update to Letter 36619 with new Hoosier Contingency Decal Info

#36624 from Robey Clark · Rule change · TB 24-09 (2024-09 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows:
"Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose
to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the
rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including
SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1)
decal must be located on each side of the car and one (1) decal must be visible on the front."

2024-09-01 AS Mustang transmission ratios

#36662 from American Sedan Committee · Rule change · TB 24-09 (2024-09 Fastrack)

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2024-10-01 SRF Update SRF3 Air Filter Rule

#36681 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.2.H.23, change as follows:
"Air Filter: P/N WM301020 or K&N RC-9160"

2024-10-01 SRF Update SRF Brake Rotor Thickness

#36687 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with
no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."

2024-10-01 SRF Hoosier Tire Decal Placement

#36739 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.2.B, change as follows:
"Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the
nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."

2024-11-01 T4 Bop Request 06-11 Honda Civic Si

#37013 from Mathew Milford · Rule change · TB 24-11 (2024-11 Fastrack)

In T4 Spec Lines, Honda Civic Si (06-11), add to Notes the following:
"LSD is permitted according to category rules."

2024-12-01 T4 Redundant Verbiage Regarding Mustang Spec Lines for Driveshaft

#36484 from David Mead · Rule change · TB 24-12 (2024-12 Fastrack)

In T2 Spec Lines, change Notes as follows:
Ford Mustang V6 (11-14): "Alternate driveshaft is allowed."
Ford Mustang Boss 302 (12-13): "Alternate driveshaft is allowed."
Ford Mustang GT 5.0L (11-14): "Alternate driveshaft is allowed."
Ford Mustang GT 5.0L (15-17): "Alternate driveshaft is allowed."
Ford Mustang GT 5.0L (2018-): "Alternate driveshaft is allowed. Springs up to 800#/in front and rear permitted. Alternate
metallic driveshaft permitted."
Ford Mustang Coupe GT & Shelby GT 4.6L (05-10): "Alternate driveshaft is allowed."

2024-12-01 T4 R53 Mini Cooper S Weight Reduction Request

#36612 from Manvinder Singh · Rule change · TB 24-12 (2024-12 Fastrack)

In T4 Spec Lines, Mini Cooper S R53 (02-06), add to Notes as follows:
"Alta 15% Pulley #AMPENG20X allowed."

2024-12-01 T4 Allowable Wheel Offset

#36855 from Robert Maples · Rule change · TB 24-12 (2024-12 Fastrack)

In GCR Section 9.1.9.2.D.7. Wheels and Tires, change as follows:
"a. Wheels
1. Any type wheel suitable for competition may be used, provided:
a. Any wheel not exceeding the specified diameter and rim width on the vehicle’s specification line may be used. Each wheel,
measured without weights, must weigh at least 15 lbs.
b. Wheels are permitted any offset provided the tire tread (that portion of the tire that contacts the ground) does not protrude
beyond the fender opening when viewed from 9.1.9.2.Touring (T2-T4) Category Specifications GCR - 660 the top perpendicular
to the ground, unless specified differently on the individual spec line for that car. To determine compliance the vehicle should be

2024-12-01 T4 Fuel Emissions Components

#37076 from Derrick Ambrose · Rule change · TB 24-12 (2024-12 Fastrack)

In GCR, Section 9.1.9.2.D.1.c. add the following:
"5. Removal of ancillary fuel tank equipment charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket
fuel cell installations."

2024-12-01 T4 2019-2024 Mazda 3 for T4

#37077 from Derrick Ambrose · Rule change · TB 24-12 (2024-12 Fastrack)

In T4 Spec Lines, classify Mazda 3 (19-24), as follows:

A specification table follows in the original; it is not shown here.

2024-12-01 T4 fix brake wording

#37129 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

In GCR, Section, 9.1.9.2.D.6. Brakes, change as follows:
"a. Components
1. The make and material of brake pads and linings may be changed.
2. Brake fluid may be substituted with any brake fluid.
3. Brake rotor dust shields may be removed or replaced to accommodate brake ducts.
4. Flexible rubber brake lines may be replaced with Teflon lined, metal braided hoses.
5. Any brake ducts are permitted, but they must serve no other purpose. Fender liners may be modified solely for routing and
attachment of brake ducts. Duct intake openings may be created by the opening of 2 sections up to 14.5 square inches each in

2024-12-01 T4 Evaporative emissions systems

#37130 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

In GCR, Section, 9.1.9.2.D.1.c., add the following:
"5. Removal of ancillary fuel tank equipment; charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket
fuel cell installations."

2024-12-01 T4 Allow Spec MX5 upgrade kit for 2009-11 RX8 S2 Transmision

#37140 from Chris Braunlich · Rule change · TB 24-12 (2024-12 Fastrack)

In T4 Spec Lines, add the following to Notes:
Mazda RX-8 Base/R3/Sport/ GT (04-12): "Transmission kit # 0000-02-5700 permitted.
Mazda MX-5 / Club Model (06-15): "Transmission kit # 0000-02-5700 permitted."
In T3 Spec Lines, add the following to Notes:
Mazda MX-5 / Club Model (06-15): "Transmission kit # 0000-02-5700 permitted."
Mazda RX-8 Base/R3/Sport/ GT (04-12): "Transmission kit # 0000-02-5700 permitted."

2024-12-01 T4 Move Spec Boxster to T4

#37158 from Rob Piekarczyk · Rule change · TB 24-12 (2024-12 Fastrack)

In T4 Spec Lines, classify Porsche Spec Boxster, as follows:

A specification table follows in the original; it is not shown here.

2024-12-01 T4 3.7 Mustangs to T4

#37188 from Scotty B White · Rule change · TB 24-12 (2024-12 Fastrack)

In T4 Spec Lines, classify Ford Mustang V6 (05-14), as follows:

A specification table follows in the original; it is not shown here.

Applies to Ford Mustang on this page: Scotty B White, Paolo Salvatore

2024-12-01 T4 BMW 320i Spec Line

#37204 from chi ho · Rule change · TB 24-12 (2024-12 Fastrack)

In T4 Spec Lines, BMW 320i (14-15), change Notes as follows:
"**This Spec line will expire 12/31/24, Please submit to appeal** Turner Motorsports intercooler #024703TMS02 allowed."

2024-12-01 T4 MX5 2006-2015 NC Help

#37221 from Richard Mooney · Rule change · TB 24-12 (2024-12 Fastrack)

Thank you for your letter. Please see changes in letter #37281 in current Fastrack.

2024-12-01 T4 Classification for a 2005 Cadillac CTS 3.6 liter 6 speed manual

#37224 from Timothy Nash · Rule change · TB 24-12 (2024-12 Fastrack)

In T3 Spec Lines, classify Cadillac CTS (02-07) as follows:

2024-12-01 T4 Civic SI in T4

#37248 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

In T4 Spec Lines, Honda Civic Si (06-11), change as follows:
Required Restrictor: "55mm flat plate restrictor required."
Min Weight: "2950 2900"
Notes: "The following items must remain stock: transmission differential - unless specified below. 55mm flat plate restrictor
required. LSD IS PERMITTED ACCORDING TO CATEGORY RULES"

2024-12-01 T4 2006-2015 T4 NC Mx5 spec line

#37278 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

In T4 Spec Lines, Mazda MX-5 / Club Model (06-15), change Notes as follows:
"Factory bolt-in roll bar/cross member may be removed to facilitate roll cage installation. MSR option permitted. Suspension
package permitted with a 100 lbs. weight increase that includes the following parts: front spring mount PT#-0000-04-5259, front
springs #0000-04-9700-08, rear spring mount PT#-0000-04-5258, rear springs #0000-04-9400-07, helper springs #0000-04-HLPR-
EB (optional), Swaybar kit – PT#-0000-04-5306-EB that includes (front sway bar kit PT#0000-04- 5306-FT, rear sway bar kit PT#-
0000-04-5306-RR), offset front camber bushing PT#-0000-04- 5407-NC. Mazda Motorsports cold air intake part #0000-06-5150-
KT allowed. Mazda Motorsport RX8 rear Hub Conversion kit part number 0000-04-5811-KT allowed, RX8 front hubs PT# F189-33-
04X allowed. The SM5 suspension (only) is allowed with a 100 lbs. weight increase. Allow Mazda header part numbers 0000-06-

Applies to Mazda MX-5 on this page: Marc Cefalo, Robert Spence, Kevin Fryer, Richard Mooney, Sergio Zlobin

2024-12-01 T4 ND MX-5 wheel allowance

#37279 from Josh Smith · Rule change · TB 24-12 (2024-12 Fastrack)

In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), change Wheel Size as follows:
"17 x 7.5"

Applies to Mazda Miata on this page: Jonathan Neudorf, Ethan Barker, Charles Habisreutinger, Ayden Rose

Applies to Mazda MX-5 on this page: Marc Cefalo, Robert Spence, Kevin Fryer, Richard Mooney, Sergio Zlobin

2024-12-01 T4 T4 BOP

#37281 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change as follows:
Required Restrictor: "60mm 59mm"
Weight: "3125 3200"
In T4 Spec Lines, Mazda MX-5 / Club Model (06-15), change weight as follows:
"2600 2550"

Applies to Mazda MX-5 on this page: Marc Cefalo, Robert Spence, Kevin Fryer, Richard Mooney, Sergio Zlobin

2024-12-01 T4 Allow 7.5

#37286 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), change Wheel Size as follows:
"17 x 7.5"

2025-01-01 AS Increase Coyote Engine Restrictor to 80mm

#36177 from Gregory Eaton · Rule change · TB 25-01 (2025-01 Fastrack)

2025-01-01 AS Performance Pack for 2015+ Mustang

#36867 from Michael Kamalian · Rule change · TB 25-01 (2025-01 Fastrack)

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2025-01-01 T4 2016-2018 Mazda Miata MX5

#37085 from Nic Piekarski · Rule change · TB 25-01 (2025-01 Fastrack)

In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), change Min Weight as follows:
"2650 2575"
In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), add to Notes the following:
"Mazda header 0000-06-5410 allowed."

Applies to Mazda Miata on this page: Jonathan Neudorf, Ethan Barker, Charles Habisreutinger, Ayden Rose

Applies to Mazda MX-5 on this page: Marc Cefalo, Robert Spence, Kevin Fryer, Richard Mooney, Sergio Zlobin

2025-01-01 AS Gear Ratios

#37131 from Timothy White · Rule change · TB 25-01 (2025-01 Fastrack)

2025-01-01 AS ECU specs for LS engine

#37208 from Gary Mathews · Rule change · TB 25-01 (2025-01 Fastrack)

Applies to Chevrolet Camaro Z-28 on this page: Phillip Waters

2025-01-01 T4 Remove spec lines that have expired

#37269 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

In T2, Effective 1/1/2025, delete for following Spec Lines in their entirety:
"Acura TL SHAWD (10-13)
Audi S4 (12-14)
Audi S5 (13-14)
Audi TT RS (2018-)
Cadillac ATS-V (16-17)
Cadillac CTS-V (06-07)
Chevrolet Camaro SS (98-02)

2025-02-01 T4 Ford Mustang V6 (05-14)

#37516 from Touring Committee · Rule change · TB 25-02 (2025-02 Fastrack)

In T4 Spec Lines, Ford Mustang V6 (05-14), change as follows:
Final drive: "3.45"
Notes: "GT/CS front bumper cover #AR3Z-17D957-BA, allowed if used with front fascia."

Applies to Ford Mustang on this page: Scotty B White, Paolo Salvatore

2025-02-01 T4 Request to Classify Club Spec in Appropriate Touring Classes

#37523 from Andrew Benagh · Rule change · TB 25-02 (2025-02 Fastrack)

In T3 Spec Lines, classify Ford SCCA Club Spec Mustang (CSM) as follows:

A specification table follows in the original; it is not shown here.

Applies to Mazda MX-5 on this page: Marc Cefalo, Robert Spence, Kevin Fryer, Richard Mooney, Sergio Zlobin

2025-03-01 AS Race memo

#37902 from American Sedan Committee · Rule change · TB 25-03 (2025-03 Fastrack)

2025-04-01 AS Flotek Head Plunge Cut Inconsistencies

#37502 from Pamela Richardson · Rule change · TB 25-04 (2025-04 Fastrack)

2025-04-01 AS Notes clean up

#37693 from American Sedan Committee · Rule change · TB 25-04 (2025-04 Fastrack)

2025-04-01 SRF Driver Safety & Comfort

#37966 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)

In SRF, GCR section 9.1.8.D.1.D, add the following:
"f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

2025-04-01 SRF Update SADEV transmission specs

#37992 from Club Racing Board · Rule change · TB 25-04 (2025-04 Fastrack)

In SRF, GCR section 9.1.8.D.2.K, change as follows:
"OR
SADEV-SRF3 6-Speed Sequential (beginning from Oct. 4, 2021 onward):
1st 12-36 3.0000 : 1
2nd 15-31 2.0667 : 1
3rd 18-28 1.5556 : 1
4th 22-28 1.2727 : 1
5th 24-26 1.0833 : 1

2025-05-01 T4 Correct Ring and Pinion Ratio to T3, Sorry I Mean T4 3.7 V6 Stang

#38041 from David Mead · Rule change · TB 25-05 (2025-05 Fastrack)

In T4 Spec Lines, Ford Mustang V6 (05-14), add to Notes the following:
"GT 8.8 rear axle assembly allowed. 3.45 or 3.55 final drive ratio allowed. 7.5 rear axle assembly with 3.45:1 final drive allowed."

Applies to Ford Mustang on this page: Scotty B White, Paolo Salvatore

2025-05-01 AS Errors and Omission

#38055 from American Sedan Committee · Rule change · TB 25-05 (2025-05 Fastrack)

2025-05-01 T4 T4 Mustang

#38058 from Scotty B White · Rule change · TB 25-05 (2025-05 Fastrack)

In T4 Spec Lines, Ford Mustang V6 (05-14), add to Notes as follows:
"OEM style rear deck spoiler similar to Laguna/CS packages permitted.”

Applies to Ford Mustang on this page: Scotty B White, Paolo Salvatore

2025-05-01 AS Request to Add LS1/LS6 Intakes for 5.3L Truck Engine EnO

#38197 from Jim Clark · Rule change · TB 25-05 (2025-05 Fastrack)

2025-06-01 T4 T4 Mustang

#38059 from Scotty B White · Rule change · TB 25-06 (2025-06 Fastrack)

In T4 Spec Lines, Ford Mustang V6 (05-14), change as follows:
Final Drive: "3.45 or 3.31"
"Weight: "3400 3300"

Applies to Ford Mustang on this page: Scotty B White, Paolo Salvatore

2025-06-01 T4 SSC tire allowance

#38216 from Benjamin Bunk · Rule change · TB 25-06 (2025-06 Fastrack)

In T4 Spec Lines, Scion FR-S Solo Spec Coupe (13-16), change Notes as follows:
"Any 200TW 225/45/17 or 215/45/17 DOT tire permitted."
In T4 Spec Lines, Subaru BRZ Solo® Spec Coupe (13-16), change Notes as follows:
"Any 200TW 225/45/17 or 215/45/17 DOT tire permitted."

Applies to Scion FR-S on this page: Jennifer Roames

Applies to Subaru BRZ on this page: Angelica Sprehe

2025-06-01 AS Errors and Omissions

#38234 from American Sedan Committee · Rule change · TB 25-06 (2025-06 Fastrack)

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2025-07-01 AS RE: Previous Letter 37695 Update

#38245 from Michael Kamalian · Rule change · TB 25-07 (2025-07 Fastrack)

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton

2025-07-01 T4 Allow B-Spec cars to run in T4

#38439 from Derrick Ambrose · Rule change · TB 25-07 (2025-07 Fastrack)

In GCR, Section 9.1.9.2, Touring car eligibility, change as follows:
"Touring car eligibility: Cars are eligible for the class they are listed with a specification line and with the specific allowances
permitted. In addition T2-T4 cars may race one class up in touring classes above their specification line class as long as they are a
legal T2-T4 car and conform to their specification line allowances as classified. Cars conforming to B-Spec or C-Spec rules are
permitted to compete in Touring 4."

2025-08-01 T4 Incorrect Touring Heading

#38451 from Terry Hanushek · Rule change · TB 25-08 (2025-08 Fastrack)

In T2-T4 Spec Lines, change Table Header as follows:
"T2 ET"

2025-10-01 SRF Add HD Oil Cooler

#38979 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.V.ff, change as follows:
"SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan
permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."

2025-11-01 AS Cadillac CTS-V BOP Weight Change

#38640 from Alex Lozano · Rule change · TB 25-09 (2025-09 Fastrack)

2025-11-01 T4 02-06 Mini Cooper Gear Ratios

#38966 from Trenton Kramer · Rule change · TB 25-11 (2025-11 Fastrack)

In T4 Spec Lines, Mini Cooper S R53 (02-06), change Gear Ratios as follows:
"12.79, 7.79, 5.65, 4.62, 3.83, 3.13 or overall- 11.42, 7.18, 5.39, 4.40, 3.65, 2.96"

2025-11-01 T4 Reinstatement of the 2005-2010 Cobalt into T4

#38987 from Tim Little · Rule change · TB 25-11 (2025-11 Fastrack)

In T4 Spec Lines, classify Chevrolet Cobalt SS, Sport Coupe (06-10) as follows:

A specification table follows in the original; it is not shown here.

2025-11-01 T4 Request to Classify Mercedes C230K

#39080 from Patrick Morgan · Rule change · TB 25-11 (2025-11 Fastrack)

In T4 Spec Lines, classify Mercedes C230 Kompressor (2002-2005) as follows:

A specification table follows in the original; it is not shown here.

2025-11-01 T4 ND Gearset Request for T4

#39166 from Josh Smith · Rule change · TB 25-11 (2025-11 Fastrack)

In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), add to Notes the following:
"Gear kit Kit PT#- 0000-02-6100."
In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), add to Notes the following:
"Gear kit Kit PT#- 0000-02-6100."
In T3 Spec Lines, Mazda MX-5 Miata (16-18), add to Notes the following:
"Gear kit Kit PT#- 0000-02-6100."
In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, add to Notes the following:
"Gear kit Kit PT#- 0000-02-6100."

Applies to Mazda Miata on this page: Jonathan Neudorf, Ethan Barker, Charles Habisreutinger, Ayden Rose

Applies to Mazda MX-5 on this page: Marc Cefalo, Robert Spence, Kevin Fryer, Richard Mooney, Sergio Zlobin

2025-11-01 T4 E&O wheel size on ND

#39168 from Josh Smith · Rule change · TB 25-11 (2025-11 Fastrack)

In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), change Wheel Size (in.) as follows:
"17 x 7.5"

Applies to Mazda Miata on this page: Jonathan Neudorf, Ethan Barker, Charles Habisreutinger, Ayden Rose

Applies to Mazda MX-5 on this page: Marc Cefalo, Robert Spence, Kevin Fryer, Richard Mooney, Sergio Zlobin

2025-11-01 T4 ND Spec Lines Wrong PT#'s

#39170 from Josh Smith · Rule change · TB 25-11 (2025-11 Fastrack)

In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), change Notes as follows:
"Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. The following item(s) must remain
stock: transmission differential unless specified below. Retractable hardtop option permitted but must be disabled from moving
action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including
Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars
allowed. 3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02,
0000-02-5804-01). Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front springs
#0000-04-9700-08, springs up to 500lb front and 300lb rear allowed. Mazda tower brace 0000-04-5626 allowed. Mazda header

Applies to Mazda Miata on this page: Jonathan Neudorf, Ethan Barker, Charles Habisreutinger, Ayden Rose

Applies to Mazda MX-5 on this page: Marc Cefalo, Robert Spence, Kevin Fryer, Richard Mooney, Sergio Zlobin

2025-11-01 T4 Touring 4 Post-Runoffs BOP Adjustments and Changes

#39251 from Touring Committee · Rule change · TB 25-11 (2025-11 Fastrack)

In T4 Spec Lines, Acura RSX/ RSX Type-S (02-06), change Restrictor as follows:
"55mm FPR"
In T4 Spec Lines, Acura TSX (2004-2008), change Restrictor as follows:
"47mm FPR 52mm FPR"
In T4 Spec Lines, BMW Z4 2.5L (03-05) , change Weight as follows:
"3050 2950"
In T4 Spec, BMW 320i (14-15), remove this spec line in its entirety.
In T4 Spec Lines, BMW 323 (98-00), change as follows:

Applies to Ford Mustang on this page: Scotty B White, Paolo Salvatore

Applies to Mazda MX-5 on this page: Marc Cefalo, Robert Spence, Kevin Fryer, Richard Mooney, Sergio Zlobin

Applies to Subaru BRZ on this page: Angelica Sprehe

2025-12-01 AS 1994 Mustang Spec Line Request

#39104 from Barry Borgschatz, Jr · Rule change · TB 25-12 (2025-12 Fastrack)

Applies to Ford Mustang on this page: Michael Kamalian, Thomas J Ellis, Gregory Eaton, James Jost

2025-12-01 T4 Classing 1995-99 Dodge Neon SOHC

#39285 from Preston Obremski · Rule change · TB 25-12 (2025-12 Fastrack)

In T4 Spec Lines, classify Dodge/Plymouth Neon ACR SOHC/DOHC (2/4 door) (95-99) as follows:

A specification table follows in the original; it is not shown here.

2026-01-01 T4 Alternate Placement of Fuse Panel and Electronics Request

#39370 from Aaron Stehly · Rule change · TB 26-01 (2026-01 Fastrack)

In GCR, Section 9.1.9.2.D.9.d, add the following:
"8. Under-dash electronics including computers, modules and fuse boxes may be relocated so they can be easily accessed after
roll cage installation."

2026-01-01 AS Restrictor Plate Change for Gen 2 Ford Coyote Engine

#39501 from American Sedan Committee · Rule change · TB 26-01 (2026-01 Fastrack)

2026-01-01 T4 Clarify T4 Brake Rotor Allowance

#39503 from David Mead · Rule change · TB 26-01 (2026-01 Fastrack)

In GCR, Section 9.1.9.2.D.6.a.6., change as follows:
"In T2-Performance alternative rotors, including 2 piece rotors are permitted. Rotors must be within 5% of OE diameter or a
maximum diameter of 360mm.
In T3- Performance alternative rotors, including 2 piece rotors are permitted with a maximum diameter of 360mm.
T4- Performance alternative 1-piece rotors are permitted but rotors must meet the sizes listed in the spec line. Spec lines
showing alternate brake kits are also permitted to use 1-piece performance alternative rotors of the same size."

2026-02-01 AS Edelbrock manifold (& timing kit) to Chevy LS Spec Lines Request

#39055 from Jason Smith · Rule change · TB 26-01 (2026-01 Fastrack)

2026-02-01 T4 T4 and T3 Feedback

#39230 from Tim Myers · Rule change · TB 26-02 (2026-02 Fastrack)

In T4 Spec Lines, remove Ford Mustang V6 (05-14) in its entirety.

2026-02-01 T4 T4 Mustang 4.0

#39489 from Scotty B White · Rule change · TB 26-02 (2026-02 Fastrack)

In T4 Spec Lines, Ford Mustang V6 (05-10), change as follows:
Tire: "245 255"
Notes: "ABS (option code 552) allowed. FR3 Handling Pack #M-2007-FR3V6 allowed (kit does not need to be run in its entirety).
The kit includes: Dampers M-18000-A, Lowering Springs M-5300-N, Sway Bars M- 5490-C, Strut Tower Brace M-20201-F. Ford
Positraction LSD part #M-4204-C75 is allowed. Any springs max F: 500 and R: 400 permitted. Any sway bar up to F: 35mm and R:
28mm permitted. Aftermarket Shocks conforming to T4 rules allowed. Panhard bar, part # BAR-M-4264-A permitted, or any pan
hard bar permitted must be set at same length as a stock bar, center mounting hole to center mounting hole +/- 0.25 inch. An
alternative steel drive shaft is permitted; this drive shaft is otherwise unrestricted, but no modifications to other components

Applies to Ford Mustang on this page: Scotty B White, Paolo Salvatore

2026-02-01 T4 Allow Alt Bushing Material in Toe Links

#39607 from David Mead · Rule change · TB 26-02 (2026-02 Fastrack)

In GCR, Section 9.1.9.D.5.a.1., change as follows:
"T2-T4: A maximum of 3.5 degrees of negative camber is allowed on front and rear suspensions. Spec line part(s) may not be
modified to increase caster and camber. Strut suspensions may adjust camber and caster by the use of eccentric bushings,
eccentric bolts (crash bolts) at the strut-to-spindle, and/or by use of slotted adjustment plates at the top of the strut mounting
plate. If upper strut slotted adjustment plates are used, they shall be located on existing chassis structure, utilizing the
unmodified manufacturer’s original bolt holes and may not serve as reinforcement for that structure. Slotted adjustment plates
(strut camber plates) may incorporate a single spherical bearing (spherical bushing) and a ball thrust bearing per strut tower. On
other forms of suspension, camber and caster adjustment may be achieved by the use of shims and/or eccentric

2026-03-01 T4 ND MX-5 Spec Line Rewrite Request

#39802 from Josh Smith · Rule change · TB 26-03 (2026-03 Fastrack)

In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), change as follows:
Weight: "2750 2650"
Notes: "Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. The following item(s) must
remain stock: transmission differential unless specified below. Retractable hardtop option permitted but must be disabled from
moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette,
including Mazda hardtop part #0000-07-5902-ND. 29mm (f) 16mm (r) sway bars allowed. 3rd and 4th gear may be replaced with
the following parts- (0000-02- 5803-02, 0000-02-5803-01, 0000-02-5804-02, 0000-02-5804-01). Suspension package permitted
with a 100 lbs. weight increase that includes the following parts: front springs #0000-04-9700-08, s Suspension

Applies to Mazda Miata on this page: Jonathan Neudorf, Ethan Barker, Charles Habisreutinger, Ayden Rose

Applies to Mazda MX-5 on this page: Marc Cefalo, Robert Spence, Kevin Fryer, Richard Mooney, Sergio Zlobin

2026-03-01 T4 4.0 Mustang spec line cleanup

#39831 from David Mead · Rule change · TB 26-03 (2026-03 Fastrack)

In T4 Spec Lines, Ford Mustang V6 (05-10), change Notes as follows:
"ABS (option code 552) allowed. FR3 Handling Pack #M-2007-FR3V6 allowed (kit does not need to be run in its entirety). The kit
includes: Dampers M-18000-A, Lowering Springs M-5300-N, Sway Bars M- 5490-C, Strut Tower Brace M-20201-F. Ford
Positraction LSD part #M-4204-C75 is allowed. Any springs max F: 500 and R: 400 permitted. Any sway bar up to F: 35mm and R:
28mm permitted. Aftermarket Shocks conforming to T4 rules allowed. Panhard bar, part # BAR-M-4264-A permitted or any pan
hard bar permitted must be set at same length as a stock bar, center mounting hole to center mounting hole +/- 0.25 inch. An
alternative steel drive shaft is permitted; this drive shaft is otherwise unrestricted, but no modifications to other components
are permitted to facilitate its installation. An Aluminum driveshaft is allowed. Any LSD permitted. Ford brake kit M-2300-D

Applies to Ford Mustang on this page: Scotty B White, Paolo Salvatore

2026-03-01 AS Re-Organization of AS Spec lines for 2026

#39887 from American Sedan Committee · Rule change · TB 26-03 (2026-03 Fastrack)

2026-03-01 SRF SRF3 Spark Plugs

#39899 from Robey Clark · Rule change · TB 26-03 (2026-03 Fastrack)

In SRF, GCR section 9.1.8.D.2.H.18, add the following:
"Spark Plugs: P/N G301041 ONLY NGK LTR7IX-11 / Washers or sealing rings are not allowed for any purpose."