BoP Lab / Classes / P1

P1 vs FB vs STL pace at every track

Lap times across years say as much about the weather as the class. % of P1 is each class's best lap as a share of P1's on the same day, so the conditions drop out: 100% is level, less is quicker, and a move in it is the class getting faster or slower against the field.

Class · click a class to switch, + to compare alongside (up to 4)

AS +B-Spec +EP +FA +vsFB ×FC +FE2 +FF +FP +FV +FX +GT1 +GT2 +GTX +HP +P +P1×P2 +SM +SMX +SRF3 +vsSTL ×STU +T1 +T2 +T3 +T4 +Show 49 inactive classes

Series Runoffs Super Tour Both

Reference class · the yardstick the % column and chart are measured against

Tracks · untick to narrow Auto Club Speedway Barber Motorsports Park Blackhawk Farms Raceway Buttonwillow Raceway Park Circuit of St. Louis (formerly Gateway Motorsports Circuit of the Americas Daytona International Speedway Grattan Raceway Hallett Motor Racing Circuit Homestead-Miami Speedway Indianapolis Motor Speedway Laguna Seca Michelin Raceway Road Atlanta Mid-Ohio Sports Car Course New Jersey Motorsports Park NOLA Motorsports Park Pacific Raceways Pittsburgh International Race Complex Portland International Raceway Pueblo Motorsports Park Road America Sebring International Raceway Sonoma Raceway Summit Point Raceway Thunderhill Raceway Park Virginia International Raceway Watkins Glen International Willow Springs Raceway World Wide Technology Raceway

Quickest here: P1 1:17.308 James Devenport, Runoffs 2016 qualifying · FB 1:19.886 Alex Mayer, Runoffs 2016 qualifying · STL 1:35.439 John Schmitt, Runoffs 2016 qualifying

% of P1Lap times

P1FBSTLsolid race · dashed qualifying · slower is lower

P1FBSTLsolid race · dashed qualifying · each class's best lap as a share of P1's at the same event (the reference class, changeable above); 100% is level, less is quicker, so up the chart is quicker

	Event	P1			FB					STL
	Event	Qual best	Race best	Trap	Qual best	Race best	Trap	vs P1	% of P1	Qual best	Race best	Trap	vs P1	% of P1
	Road America Runoffs 20262026-09-28									2:30.537Derek Ketchie · fastest of 16 · top 5 within 2.9s-1.528s (-1.00%)	2:30.657Danny Steyn · fastest of 16 · top 5 within 0.6s-1.470s (-0.97%)	134.8Mike Taylor+2.6 mph (+2.0%)
4 rule changes (STL: 4)2 cars added · 1 weight · 1 wording · STL removes Mazda MX-5 Cup entirely; renames Spec MX5 Challenge to Spec MX5; renames Global Cup to MX-5 Cup (16-18); removes Global Cup (2019). · STL, STU weight calculation procedure clarified: positive percentages added first, negative subtracted second, then fixed weights applied. · STL adds Mazda BP 1.6, 1600cc, minimum weight 2160 lbs. · STL minimum weights increase across all engine sizes, 1300cc to 1850cc up to 195–250 lbs.showhide 2026-07-01 STL Spec Line Clean Up #40344cars addedremoved · cars addedSTL removes Mazda MX-5 Cup entirely; renames Spec MX5 Challenge to Spec MX5; renames Global Cup to MX-5 Cup (16-18); removes Global Cup (2019). 2026-06-01 STL Calculating Weight #40224wordingwordingSTL, STU weight calculation procedure clarified: positive percentages added first, negative subtracted second, then fixed weights applied. 2026-04-01 STL Classifications #39885cars addedaddedSTL adds Mazda BP 1.6, 1600cc, minimum weight 2160 lbs. 2026-01-01 STL Weight adjustment for STL #39579weightslower · weightSTL minimum weights increase across all engine sizes, 1300cc to 1850cc up to 195–250 lbs.
	Road America Runoffs 20252025-09-29									2:32.065Jose Osiris Pena · fastest of 14 · top 5 within 3.4s+2.002s (+1.33%)	2:32.127Jose Osiris Pena · fastest of 13 · top 5 within 2.4s+1.882s (+1.25%)	132.2Jon Sewell-2.1 mph (-1.5%)
3 rule changes (STL: 3)1 cars added · 1 weight · 1 wording · Lotus Evora GT4 minimum weight drops to 2700 lbs; Elise Cup R to 2250 lbs; Elise SC and Exige SC to 2450–2550 lbs. · STL Mazda MX5 Challenge minimum weight now references GCR 9.1.7.1; mandatory component spec list removed, alternative tires only allowed. · STL STU Mazda Miata alternate front hubs Mazda Motorsports Development Part #0000-04-5HUB-S1 approved.showhide 2025-08-01 STL Lotus Weight Reduction #38772weight -50 lbsfaster · weightLotus Evora GT4 minimum weight drops to 2700 lbs; Elise Cup R to 2250 lbs; Elise SC and Exige SC to 2450–2550 lbs. 2025-05-01 STL E&O: SMX Allowance in STL #37945wordingunclearSTL Mazda MX5 Challenge minimum weight now references GCR 9.1.7.1; mandatory component spec list removed, alternative tires only allowed. 2024-12-01 STL Request to Remove Miata Hubs from General category #37138cars addedaddedSTL STU Mazda Miata alternate front hubs Mazda Motorsports Development Part #0000-04-5HUB-S1 approved.
	Road America Runoffs 20242024-10-01	2:00.476Chip Romer · fastest of 12 · top 5 within 1.5s-0.625s (-0.52%)	2:00.418Matt Romer · fastest of 9 · top 5 within 2.1s-1.452s (-1.19%)	168.3Jason Miller+8.7 mph (+5.4%)						2:30.063Joe Moser · fastest of 18 · top 5 within 3.7s-1.357s (-0.90%)	2:30.245Joe Moser · fastest of 16 · top 5 within 4.2s-1.870s (-1.23%)	134.3Joe Moser+1.3 mph (+1.0%)	+29.827squal +29.587s	124.8%qual 124.6%
10 rule changes (P1: 6, STL: 4)3 weight · 2 engine · 1 aero · 4 wording · P1 engine approval process wording clarified; unspecified engines need case-by-case Board review. · P1 removes redundant effective date language from ECU stall prohibition rule. · P1 Honda K20A-FD2 engine terminology corrected from 'spec' to proper series designation; FIA certification documentation requirement removed. · STL and STU now permit electric power steering pumps, OEM electric-assisted steering, or column-mounted electric steering assist systems. · STL normally aspirated minimum weights reduced: 1900cc to 2540 lbs, 1950cc to 2583 lbs, 2000cc to 2625 lbs; short-wheelbase FWD adds 1.25%; Honda B16/B17/B18C1 throttle to 51mm, B18C Type R and Mazda MZR to 50mm. · STL Mazda 12A: 5th and 6th intake port actuators and valves may no longer be removed or disabled. · P1 Engine Table line H restrictor grows to 32 mm, weight rises to 1450 lbs; line I restrictor to 31 mm, weight to 1475 lbs. · P1 Group CN Honda K20A-FD2 removes engine modification restrictions; CRB may add intake restrictor if needed. · STL 79-85 RX7 12A now allows auto-type 2 bbl carburetor with 42mm choke on dual-y manifold, not just stock Nikki.showhide 2024-05-01 P1 Update GCR section 9.1.8.B.J.7 #35907wordingwordingP1 engine approval process wording clarified; unspecified engines need case-by-case Board review. 2024-03-01 P1 Remove redundant effective date language in GCR 9.1.8.B.J.4 #35693wordingwordingP1 removes redundant effective date language from ECU stall prohibition rule. 2024-03-01 P1 Correct engine series terminology #35694wordingwordingP1 Honda K20A-FD2 engine terminology corrected from 'spec' to proper series designation; FIA certification documentation requirement removed. 2024-02-01 STL ST Electric-Assisted Steering Systems #35066aeroadded · aeroSTL and STU now permit electric power steering pumps, OEM electric-assisted steering, or column-mounted electric steering assist systems. 2024-02-01 STL BOP Adjustments #35112weightfaster · weightSTL normally aspirated minimum weights reduced: 1900cc to 2540 lbs, 1950cc to 2583 lbs, 2000cc to 2625 lbs; short-wheelbase FWD adds 1.25%; Honda B16/B17/B18C1 throttle to 51mm, B18C Type R and Mazda MZR to 50mm. 2024-02-01 STL Mazda 12A #35320engineremoved · engineSTL Mazda 12A: 5th and 6th intake port actuators and valves may no longer be removed or disabled. 2024-01-01 P1 Please correct omitted punctuation #34890weight 2024-01-01 P1 Adjust restrictors and weights for Engine Table lines H and I #35229weightslower · weightP1 Engine Table line H restrictor grows to 32 mm, weight rises to 1450 lbs; line I restrictor to 31 mm, weight to 1475 lbs. 2024-01-01 P1 Revise Group CN Honda K20A-FD2 Spec Line #35337wordingunclearP1 Group CN Honda K20A-FD2 removes engine modification restrictions; CRB may add intake restrictor if needed. 2024-01-01 STL Alternate Carburetor Request for 79-85 RX7 12a #35181engineadded · engineSTL 79-85 RX7 12A now allows auto-type 2 bbl carburetor with 42mm choke on dual-y manifold, not just stock Nikki.
	Virginia International Raceway Runoffs 20232023-09-23	1:42.602Todd Vanacore · fastest of 10 · top 5 within 0.9s+1.001s (+0.99%)	1:44.329Todd Vanacore · fastest of 9 · top 5 within 0.7s-9.766s (-8.56%)	158.5Jason Miller+1.2 mph (+0.8%)						2:05.779Danny Steyn · fastest of 22 · top 5 within 3.4s+0.305s (+0.24%)	2:06.682Joe Moser · fastest of 20 · top 5 within 1.5s-1.150s (-0.90%)	131.8Danny Steyn+0.1 mph (+0.1%)	+22.353squal +23.177s	121.4%qual 122.6%
9 rule changes (P1: 7, STL: 2)2 aero · 1 cars added · 1 engine · 5 wording · P1 SIR testing: vehicle deemed compliant if it stalls within 3 seconds of the stall test. · P1 intake restrictor rule clarified: flat plate, venturi, or Single Inlet Restrictor required; all intake air must pass through. · P1 ducted air rule clarified: top-exit ducted air must pass through heat exchanger, except cockpit opening and engine bay vents. · STL ITA and ITS RX7, and ITS/ITA/ITB/ITC 1985+ models clarified to require tires per 9.1.4.2. · P1 aero height limit, front/rear overhang, and cockpit dimensions corrected to metric-inch equivalents. · P1 suspension covers must have symmetrical upper and lower surfaces, no airfoil cross-sections or angled downforce. · Spec MX5 in STL allows ACT clutch 0000-02-5004-G6, wheels 17x8, Toyo RR and RA1 235-40-17 tyres, or alternatives on 17x7 per rules. · P1 aerodynamic devices may not extend more than 1cm below lower surfaces rear of front axle; body panels covering suspension must not be airfoil-shaped or create downforce. · P1 forced induction prohibited: turbocharging and supercharging not allowed.showhide 2023-07-01 P1 SIR Testing #34354wordingwordingP1 SIR testing: vehicle deemed compliant if it stalls within 3 seconds of the stall test. 2023-07-01 P1 E&O Single Inlet Restrictor abbreviation, etc. #34369wordingwordingP1 intake restrictor rule clarified: flat plate, venturi, or Single Inlet Restrictor required; all intake air must pass through. 2023-07-01 P1 E&O Clean up ducted air provision #34410wordingwordingP1 ducted air rule clarified: top-exit ducted air must pass through heat exchanger, except cockpit opening and engine bay vents. 2023-06-01 STL Clarify STL table B - IT spec notes on Tires #34187wordingwordingSTL ITA and ITS RX7, and ITS/ITA/ITB/ITC 1985+ models clarified to require tires per 9.1.4.2. 2023-04-01 P1 E&O - Correct dimensional equivalents #34018wordingwordingP1 aero height limit, front/rear overhang, and cockpit dimensions corrected to metric-inch equivalents. 2023-03-01 P1 November 2022 Rules Clarification for Suspension Covers #33615aeroslower · aeroP1 suspension covers must have symmetrical upper and lower surfaces, no airfoil cross-sections or angled downforce. 2023-01-01 STL Spec MX5 in STL #33473cars addedaddedSpec MX5 in STL allows ACT clutch 0000-02-5004-G6, wheels 17x8, Toyo RR and RA1 235-40-17 tyres, or alternatives on 17x7 per rules. 2022-11-01 P1 Clarify body panel coverage of suspension components #33318aeroaeroP1 aerodynamic devices may not extend more than 1cm below lower surfaces rear of front axle; body panels covering suspension must not be airfoil-shaped or create downforce. 2022-10-01 P1 E&O clarification regarding forced induction #33123engineremoved · engineP1 forced induction prohibited: turbocharging and supercharging not allowed.
	Virginia International Raceway Runoffs 20222022-09-24	1:41.601Todd Slusher · fastest of 9 · top 5 within 2.3s-1.073s (-1.05%)	1:54.095John Mcaleer · fastest of 9 · top 5 within 1.4s+10.597s (+10.24%)	157.2Jason Miller+1.3 mph (+0.8%)						2:05.474Danny Steyn · fastest of 24 · top 5 within 2.3s-1.729s (-1.36%)	2:07.832Danny Steyn · fastest of 22 · top 5 within 1.9s+0.559s (+0.44%)	131.7Trever Degioanni-3.2 mph (-2.3%)	+13.737squal +23.873s	112.0%qual 123.5%
8 rule changes (P1: 3, STL: 5)3 engine · 1 tyres & wheels · 1 weight · 3 wording · P1 motorcycle-based engines with individual throttle bodies must use flat plate intake restrictors within 4 inches of primary butterfly. · P1 bodywork rules clarified: cycle fenders prohibited, side body minimum height at front axle centerline, air ducting for downforce banned. · STU single throttle body weight reduction removed; minimum weights revised down to 2990 lbs at 3000cc from 3300 lbs. · STL and STU Improved Touring vehicles must now conform to section 9.1.4 Tires & Wheels. · P1 2-cycle 6-cylinder maximum displacement increases to 1725 cc, restrictor shrinks to 40mm, minimum weight drops to 1275 lbs. · STL/STU intake manifold and cylinder head porting clarified as free; intake and exhaust porting wording removed. · STL Mazda Renesis flat plate restrictor increases from 55mm to 60mm. · STL 79-85 RX7 12A allows emissions removal and jet correction on stock Nikki carb.showhide 2022-08-01 P1 Clarify authorization to use flat plate intake restrictor #32964engineadded · engineP1 motorcycle-based engines with individual throttle bodies must use flat plate intake restrictors within 4 inches of primary butterfly. 2022-05-01 P1 E&O Clarification of Bodywork Rules #32468wordingwordingP1 bodywork rules clarified: cycle fenders prohibited, side body minimum height at front axle centerline, air ducting for downforce banned. 2022-03-01 STL Single TB Weight Modifiers #31449weightfaster · weightSTU single throttle body weight reduction removed; minimum weights revised down to 2990 lbs at 3000cc from 3300 lbs. 2022-03-01 STL Improved Touring Tires #32063tyres & wheelstyres & wheelsSTL and STU Improved Touring vehicles must now conform to section 9.1.4 Tires & Wheels. 2022-01-01 P1 Displacement & Weight Change Request for 2-Cycle 6 Cylinder #31609enginefaster · engineP1 2-cycle 6-cylinder maximum displacement increases to 1725 cc, restrictor shrinks to 40mm, minimum weight drops to 1275 lbs. 2022-01-01 STL Throttling Device Clarification #31323wordingwordingSTL/STU intake manifold and cylinder head porting clarified as free; intake and exhaust porting wording removed. 2022-01-01 STL Mazda Renesis Restriction #31467enginefaster · engineSTL Mazda Renesis flat plate restrictor increases from 55mm to 60mm. 2022-01-01 STL Clarification of 79-85 RX7 Spec line #31621wordingwordingSTL 79-85 RX7 12A allows emissions removal and jet correction on stock Nikki carb.
	Indianapolis Motor Speedway Runoffs 20212021-09-25	1:29.011Lee Alexander · fastest of 13 · top 5 within 2.5s-1.783s (-1.96%)	1:29.225Lee Alexander · fastest of 12 · top 5 within 3.5s-2.274s (-2.49%)	160.1Jason Miller						1:51.665Danny Steyn · fastest of 42 · top 5 within 1.7s-0.982s (-0.87%)	2:02.711Joe Moser · fastest of 37 · top 5 within 3.2s+10.122s (+8.99%)	131.8Max Gee	+33.486squal +22.654s	137.5%qual 125.5%
26 rule changes (P1: 11, STL: 15)5 engine · 4 cars added · 2 aero · 2 weight · 1 induction · 1 suspension & brakes · 9 wording · 2 other · P1 creates separate spec lines H and I for 2000cc and 2300cc engines at 1400 and 1445 lbs minimum weight respectively. · P1 Staudacher may run 950 lbs minimum weight with 38.5mm flat plate intake restrictor, removing prior weight-linked restrictor rule. · STL Mazda Spec MX-5 removes redundant specification line referencing 2014 regulations. · P1 adds 1355cc motorcycle-based engine line C at 1075 lbs minimum weight, no restrictor required. · STL Volkswagen 2.0L TFSI 1984 cc engine permitted without turbocharger, meeting all other STL specs. · P1 cockpit opening section allows tonneau covers to meet minimum dimensions; wording clarified on equipment attachment. · P1 Staudacher 1005cc homologated before 1-1-2014 may run 38.5mm flat plate intake restrictor at 950 lbs minimum weight. · P1 Spec Line C: FPIR not required at 1150 lbs, 1355cc max may run without FPIR at 1075 lbs. Spec Line G: up to 2000cc runs 30mm SIR at 1400 lbs, 2300cc runs 30mm SIR at 1445 lbs. · P1 classes B, C, D maximum valves per cylinder set to 4, previously unspecified. · STL Pontiac Solstice/Saturn Sky allowed 4 inch ride height. · STL Mazda B5 DOHC added to class; must meet all STL regulations. · STL Honda B16A (JDM) restrictor reduced from 54mm to 53mm. · P1 Spec Line A clarifies carburetor induction only, one per cylinder, balance tubes not allowed. · P1 Spec Line H notes clarify peripheral port or bridgeport allowed; wording only. · ST oil coolers and filters now explicitly listed as addable or substitutable parts in vents and breathers section. · P1 Elan DP02-spec Mazda MZR sealed engine option removed effective 3/1/2021. · P1 Engine Table Spec Lines C and G change 'inlet restrictor' to 'intake restrictor' terminology. · STL GM Ecotec LNF now permits any Ecotec engine family with 55mm flat plate restrictor. · ST 90-05 Mazda Miata allowed alternate front wheel hub Mazda Motorsports Development Part #0000-04-5HUB-S1. · ST cars may now relocate ABS actuation hardware and wiring anywhere in the engine compartment. · STL rear wing trailing edge may be mounted no further rearward than the center of the rearmost part approved bodywork. · STL alternate transmissions now allow OEM gear sets and input shaft modifications for fitment. · STL RWD strut-front cars lose 2.5% weight penalty, others lose 3% penalty for FWD parity. · STL Honda F20C drops 2% weight penalty, minimum weight reduced. · STL Honda B16/B17/B18C1 restrictor reduced to 53mm, B18C variants and Mazda MZR to 52mm. · ST aero devices and reference areas must include end plates, exclude fasteners under 1/2" protrusion.showhide 2021-09-01 P1 Move 2000cc and 2300cc engine options to individual spec lines #31012cars addedaddedP1 creates separate spec lines H and I for 2000cc and 2300cc engines at 1400 and 1445 lbs minimum weight respectively. 2021-09-01 P1 E&O Spec Line B notes #31095wordingwordingP1 Staudacher may run 950 lbs minimum weight with 38.5mm flat plate intake restrictor, removing prior weight-linked restrictor rule. 2021-09-01 STL Request to clean up Spec MX-5 Redundancy #31069wordingwordingSTL Mazda Spec MX-5 removes redundant specification line referencing 2014 regulations. 2021-08-01 P1 Add 1355cc spec line #30890cars addedaddedP1 adds 1355cc motorcycle-based engine line C at 1075 lbs minimum weight, no restrictor required. 2021-06-01 STL VW Engine Request #30625engineadded · engineSTL Volkswagen 2.0L TFSI 1984 cc engine permitted without turbocharger, meeting all other STL specs. 2021-05-01 P1 E&O tonneau cover provision in cockpit opening section #30458wordingwordingP1 cockpit opening section allows tonneau covers to meet minimum dimensions; wording clarified on equipment attachment. 2021-05-01 P1 Update Spec Line B Notes #30498wordingwordingP1 Staudacher 1005cc homologated before 1-1-2014 may run 38.5mm flat plate intake restrictor at 950 lbs minimum weight. 2021-05-01 P1 Update Spec Lines C and G notes #30499wordingwordingP1 Spec Line C: FPIR not required at 1150 lbs, 1355cc max may run without FPIR at 1075 lbs. Spec Line G: up to 2000cc runs 30mm SIR at 1400 lbs, 2300cc runs 30mm SIR at 1445 lbs. 2021-05-01 P1 E&O Maximum Valves Per Cylinder #30559engineengineP1 classes B, C, D maximum valves per cylinder set to 4, previously unspecified. 2021-05-01 STL Solstice Ride Height #30183otheraddedSTL Pontiac Solstice/Saturn Sky allowed 4 inch ride height. 2021-05-01 STL Request Mazda B5 DOHC #30420cars addedaddedSTL Mazda B5 DOHC added to class; must meet all STL regulations. 2021-05-01 STL Honda B16A (JDM) Restrictor change #30531engineslower · engineSTL Honda B16A (JDM) restrictor reduced from 54mm to 53mm. 2021-04-01 P1 Clean up Spec Line A notes section #30424wordingwordingP1 Spec Line A clarifies carburetor induction only, one per cylinder, balance tubes not allowed. 2021-04-01 P1 Clean up Spec Line H notes section #30425wordingwordingP1 Spec Line H notes clarify peripheral port or bridgeport allowed; wording only. 2021-04-01 STL ST Oil Coolers E&O Correction to 9.1.4.2.H #30388wordingwordingST oil coolers and filters now explicitly listed as addable or substitutable parts in vents and breathers section. 2021-03-01 P1 DP02 Sealed 2ltr Engine Option #30038engineremoved · engineP1 Elan DP02-spec Mazda MZR sealed engine option removed effective 3/1/2021. 2021-03-01 P1 E&O restrictor terminology #30285wordingwordingP1 Engine Table Spec Lines C and G change 'inlet restrictor' to 'intake restrictor' terminology. 2021-03-01 STL GM Ecotec engines in STL #30247engineadded · engineSTL GM Ecotec LNF now permits any Ecotec engine family with 55mm flat plate restrictor. 2021-03-01 STL Super Touring Alternate Miata Hubs #30345cars addedaddedST 90-05 Mazda Miata allowed alternate front wheel hub Mazda Motorsports Development Part #0000-04-5HUB-S1. 2021-02-01 STL Brake Component Relocation #29990suspension & brakessuspension & brakesST cars may now relocate ABS actuation hardware and wiring anywhere in the engine compartment. 2021-02-01 STL Super Touring Wing Clarification #30111aeroaeroSTL rear wing trailing edge may be mounted no further rearward than the center of the rearmost part approved bodywork. 2021-02-01 STL Transmission Options #30118otheraddedSTL alternate transmissions now allow OEM gear sets and input shaft modifications for fitment. 2021-01-01 STL Request for FWD and RWD Parity #29728weightfaster · weightSTL RWD strut-front cars lose 2.5% weight penalty, others lose 3% penalty for FWD parity. 2021-01-01 STL Request to Remove Honda F20C 2% Weight Penalty #29815weightfaster · weightSTL Honda F20C drops 2% weight penalty, minimum weight reduced. 2021-01-01 STL Request for FWD and RWD Parity #30023inductionslower · inductionSTL Honda B16/B17/B18C1 restrictor reduced to 53mm, B18C variants and Mazda MZR to 52mm. 2020-12-01 STL Request clarification on wing measurement #29640aeroaeroST aero devices and reference areas must include end plates, exclude fasteners under 1/2" protrusion.
	Road America Runoffs 20202020-10-02	2:01.101James French · fastest of 18 · top 5 within 1.1s	2:01.870James French · fastest of 17 · top 5 within 1.8s	159.7David Locke						2:31.420Danny Steyn · fastest of 33 · top 5 within 3.1s	2:32.115Joe Moser · fastest of 30 · top 5 within 1.5s	132.9Darin Treakle	+30.245squal +30.319s	124.8%qual 125.0%
15 rule changes (P1: 4, STL: 11)5 engine · 4 cars added · 1 induction · 1 removed · 4 wording · STL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis percentage additions, subtractions, and fixed pounds. · STL STU rear wing Gurney flap terminology clarified from wicker to Gurney flap in mounting and chord rules. · GT3 and STU add Borg-Warner EFR6258 turbocharger to approved turbo lists. · STL adds Mazda MX-5 Global Cup 16-18 at 2450 lbs minimum and 2019 at 2550 lbs minimum. · STL Mazda MX-5 Club 06-15 allowed header part number 0000-06-5407-NC. · STL Acura/Honda B18 and B18C engines: restrictor sizes swapped, B18C1 removed from allowed variants. · P1 intake manifolds unrestricted unless engine requires flat plate restrictor; no plenums or balance pipes on restricted individual runner manifolds. · STL Honda B18 loses 53mm restrictor requirement; B18C1 added with 54mm restrictor, B18C1 removed from other variants. · STU GM Ecotech LNF now permitted without turbo, with LE5 head and intake manifold, meeting STL specs. · STL Mazda MZR restrictor reduced from 54 mm to 53 mm. · STL Mazda MZR restrictor reduces from 55 mm to 53 mm. · STL Mazda Spec MX5 Challenge adds approved wheel part numbers 0000-04-5706-GM, 0000-04-5706-SL to notes. · P1 sealed 2.0L Elan DP02-spec Mazda option removal date extended from 1/1/2020 to 1/1/2021. · P1 sealed 2.0 MZR engine removed effective 1/1/2020; competitors may run it under Spec Line G. · P1 Spec Line F: Restricted 2.0L Group becomes CN-spec Honda K20A-FD2, 2000cc, 1400 lbs minimum.showhide 2020-08-01 STL Minimum Weight Determination #27695wordingwordingSTL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis percentage additions, subtractions, and fixed pounds. 2020-08-01 STL ST Gurney flap Wicker clarification #29012wordingwordingSTL STU rear wing Gurney flap terminology clarified from wicker to Gurney flap in mounting and chord rules. 2020-07-01 STL Request for Addition to GT3 Approved Turbo List #27576cars addedaddedGT3 and STU add Borg-Warner EFR6258 turbocharger to approved turbo lists. 2020-06-01 STL Request to add 2016-2019 GMX-5 Spec line #28604cars addedaddedSTL adds Mazda MX-5 Global Cup 16-18 at 2450 lbs minimum and 2019 at 2550 lbs minimum. 2020-06-01 STL Request to update PN for MX-5 #28622cars addedaddedSTL Mazda MX-5 Club 06-15 allowed header part number 0000-06-5407-NC. 2020-06-01 STL Correction - Clarification Honda/Acura B18B engine Letter # 26209 #28873wordingwordingSTL Acura/Honda B18 and B18C engines: restrictor sizes swapped, B18C1 removed from allowed variants. 2020-05-01 P1 E&O minimum weights and intake manifolds #28731inductioninductionP1 intake manifolds unrestricted unless engine requires flat plate restrictor; no plenums or balance pipes on restricted individual runner manifolds. 2020-05-01 STL STL Honda B18 restrictor changes #28794enginefaster · engineSTL Honda B18 loses 53mm restrictor requirement; B18C1 added with 54mm restrictor, B18C1 removed from other variants. 2020-04-01 STL Change GM LNF 2.0 Allowance to LSJ Engine for Viable STL 2.0 #27884engineadded · engineSTU GM Ecotech LNF now permitted without turbo, with LE5 head and intake manifold, meeting STL specs. 2020-04-01 STL Acura/Honda B18C engine chart. Reduce the current 54 mm flat plat #28663engineslower · engineSTL Mazda MZR restrictor reduced from 54 mm to 53 mm. 2020-04-01 STL Mazda MZR engine chart. Reduce the current 55 mm flat plate to 53 #28664engineslower · engineSTL Mazda MZR restrictor reduces from 55 mm to 53 mm. 2020-03-01 STL Request to add wheel part numbers #28342cars addedaddedSTL Mazda Spec MX5 Challenge adds approved wheel part numbers 0000-04-5706-GM, 0000-04-5706-SL to notes. 2020-02-01 P1 Extend date for removing sealed DP02-spec 2.0L option #28046wordingunclearP1 sealed 2.0L Elan DP02-spec Mazda option removal date extended from 1/1/2020 to 1/1/2021. 2020-01-01 P1 Remove sealed DP02-spec 2.0 MZR spec #26753removedremovedP1 sealed 2.0 MZR engine removed effective 1/1/2020; competitors may run it under Spec Line G. 2020-01-01 P1 Update Revised Spec Line F #27745engineengineP1 Spec Line F: Restricted 2.0L Group becomes CN-spec Honda K20A-FD2, 2000cc, 1400 lbs minimum.
	Virginia International Raceway Runoffs 20192019-10-05	1:42.674Todd Slusher · fastest of 14 · top 5 within 1.5s	1:43.498Todd Slusher · fastest of 13 · top 5 within 1.0s	155.9Jim Devenport	1:54.469Pete Frost · only car	1:57.688Pete Frost · only car	145.9Pete Frost	+14.190squal +11.795s	113.7%qual 111.5%	2:07.203Danny Steyn · fastest of 36 · top 5 within 1.8s	2:07.273Cliff Ira · fastest of 35 · top 5 within 1.4s	134.8Cliff Ira	+23.775squal +24.529s	123.0%qual 123.9%
25 rule changes (P1: 14, STL: 11)4 cars added · 3 engine · 1 weight · 14 wording · 3 other · STL adds Mazda Spec MX-5 Challenge, 2000cc displacement, 2500 lb minimum weight, with mandatory Roush, Penske, Eibach, and other specified components. · P1 traction control prohibited. · P1 permits mechanical, solenoid, and air-shifters; prohibits electronic pre-selection and multi-wheel power. · P1 minimum bodywork height rule moved and restated with new 115cm aerodynamic part height limit. · P1 consolidates fender louver rules into one section; removes duplicate allowance for louvers and clarifies brake and engine air ducts are permitted. · STU allows alternate intake manifolds on case-by-case basis; stock throttle device and manifold otherwise required. · P1 anti-intrusion panels now allowed anywhere on chassis sides instead of specified locations. · P1 bodywork wording clarified: comfort and safety for driver and passenger or driver only. · STL Acura/Honda B18 except C engine restrictor increased from 53mm to 54mm flat plate. · P1 Engine Table reference cleaned up; no performance change. · P1 Mazda Renesis Rotary engine spec line removed from Engine Table. · STL and STU ride height measurement clarified: lowest rocker panel point without driver, excluding pinch weld. · P1 Staudacher and Honda K20A-FD2 engine table wording clarified; no performance change. · P1 closed cockpit single-seat cars remain prohibited; rule moved from subsection J.5 to B.4. · STL adds VW 1.8L R4 20VT 1781 cc, 1781 minimum weight, naturally aspirated only. · STL Mazda Renesis minimum weight reduced to 2700 lbs. · STL Mazda MX-5 Cup brake pad compound now open. · STL adds Acura/Honda B18C1 GSR with 1797cc displacement, 54mm flat plate restrictor required, porting outside 1" allowance prohibited. · STL Mazda 12 and 13B now permit port matching; porting ban removed. · P1 engine table reference corrected from 'above' to 'below'; ETC/FBW/DBW throttle wording clarified on sensor and fail-safe requirements. · P1 removes TIR inlet restrictor option; deletes requirement for single turbo/supercharger unit with single restrictor. · P1 CN-spec Honda K20A-FD2 clarified: stock OEM parts required, no machining allowed. · P1 engine rules correct grammar and remove head designs from specification table. · STL B17 now requires 54mm flat plate restrictor; B18C Type R variants move to 54mm restrictor, weight chart baseline. · STL Mazda Miata removes maximum displacement limit; minimum weight corrected to unspecified figure.showhide 2019-10-01 STL Request to Classify Spec MX-5 Challenge in STL #27399cars addedaddedSTL adds Mazda Spec MX-5 Challenge, 2000cc displacement, 2500 lb minimum weight, with mandatory Roush, Penske, Eibach, and other specified components. 2019-08-01 P1 E&O Transmissions #27098wordingwordingP1 traction control prohibited. 2019-07-01 P1 E&O Transmissions #27005otheraddedP1 permits mechanical, solenoid, and air-shifters; prohibits electronic pre-selection and multi-wheel power. 2019-07-01 P1 Move minimum height provision to #27031wordingwordingP1 minimum bodywork height rule moved and restated with new 115cm aerodynamic part height limit. 2019-07-01 P1 Remove duplicative fender louver provision #27033wordingwordingP1 consolidates fender louver rules into one section; removes duplicate allowance for louvers and clarifies brake and engine air ducts are permitted. 2019-07-01 STL Request clarification for manifold and throttle in STU #27004wordingwordingSTU allows alternate intake manifolds on case-by-case basis; stock throttle device and manifold otherwise required. 2019-05-31 P1 Missing word E&O #26919wordingwordingP1 anti-intrusion panels now allowed anywhere on chassis sides instead of specified locations. 2019-05-31 P1 E&O correction to GCR 9.1.8.C.C. #26927wordingwordingP1 bodywork wording clarified: comfort and safety for driver and passenger or driver only. 2019-05-31 STL Request Restrictor Plate correction #26779enginefaster · engineSTL Acura/Honda B18 except C engine restrictor increased from 53mm to 54mm flat plate. 2019-05-01 P1 Clean up reference to engine table #26648wordingwordingP1 Engine Table reference cleaned up; no performance change. 2019-05-01 P1 Remove redundant spec line #26692cars addedremoved · cars addedP1 Mazda Renesis Rotary engine spec line removed from Engine Table. 2019-05-01 STL Request Ride Height Clarification #26597wordingwordingSTL and STU ride height measurement clarified: lowest rocker panel point without driver, excluding pinch weld. 2019-04-01 P1 Clean Up Engine Table Language #26590wordingwordingP1 Staudacher and Honda K20A-FD2 engine table wording clarified; no performance change. 2019-03-01 P1 Move single-seat closed cockpit provision to #26376wordingwordingP1 closed cockpit single-seat cars remain prohibited; rule moved from subsection J.5 to B.4. 2019-03-01 STL Request to Allow VW 1.8L Engine #25614cars addedaddedSTL adds VW 1.8L R4 20VT 1781 cc, 1781 minimum weight, naturally aspirated only. 2019-03-01 STL Request to reduce weight of RX8 with Renesis rotary #25781weight -100 lbsfaster · weightSTL Mazda Renesis minimum weight reduced to 2700 lbs. 2019-03-01 STL Request for Open Brake Pads On Mazda MX-5 Cup NC #25821otheraddedSTL Mazda MX-5 Cup brake pad compound now open. 2019-03-01 STL Request to clarify B18C1 GSR Honda B motor table #26209cars addedaddedSTL adds Acura/Honda B18C1 GSR with 1797cc displacement, 54mm flat plate restrictor required, porting outside 1" allowance prohibited. 2019-03-01 STL Port Matching #26415enginefaster · engineSTL Mazda 12 and 13B now permit port matching; porting ban removed. 2019-02-01 P1 Correct errors in GCR section 9.1.8.C.J #26144wordingwordingP1 engine table reference corrected from 'above' to 'below'; ETC/FBW/DBW throttle wording clarified on sensor and fail-safe requirements. 2019-01-01 P1 Remove redundant inlet restrictor provisions #25877wordingwordingP1 removes TIR inlet restrictor option; deletes requirement for single turbo/supercharger unit with single restrictor. 2019-01-01 P1 Clarify Honda K20A-FD2 parts requirement #25949wordingwordingP1 CN-spec Honda K20A-FD2 clarified: stock OEM parts required, no machining allowed. 2019-01-01 P1 Correct GCR section 9.1.8.C.J errors #25966wordingwordingP1 engine rules correct grammar and remove head designs from specification table. 2019-01-01 STL Request to equalize FPR Reduction on all B-Series Vtec Engines #24746enginefaster · engineSTL B17 now requires 54mm flat plate restrictor; B18C Type R variants move to 54mm restrictor, weight chart baseline. 2019-01-01 STL Request E&O for Mazda Miata Spec Line #25955otherunclearSTL Mazda Miata removes maximum displacement limit; minimum weight corrected to unspecified figure.
	Sonoma Raceway Runoffs 20182018-10-10	1:27.714Todd Slusher · fastest of 19 · top 5 within 2.1s	1:28.786Perry Richardson · fastest of 19 · top 5 within 0.9s	144.0Johnnie Crean	1:28.612J R Osborne · fastest of 7 · top 5 within 3.3s	1:31.189J R Osborne · fastest of 7 · top 5 within 3.7s	140.5J R Osborne	+2.403squal +0.898s	102.7%qual 101.0%	1:49.138Danny Steyn · fastest of 19 · top 5 within 2.5s	1:49.754Danny Steyn · fastest of 17 · top 5 within 2.5s	103.2Craig McHaffie	+20.968squal +21.424s	123.6%qual 124.4%
No rule changes on record between these events
	Indianapolis Motor Speedway Runoffs 20172017-09-25	1:30.794Jim Devenport · fastest of 19 · top 5 within 2.8s	1:31.499Jim Devenport · fastest of 16 · top 5 within 2.2s		1:33.746Gary Hickman · fastest of 18 · top 5 within 3.3s	1:33.702Alex Mayer · fastest of 17 · top 5 within 3.0s		+2.203squal +2.952s	102.4%qual 103.3%	1:52.647Adam Roberts · fastest of 57 · top 5 within 0.8s	1:52.589Eric Kutil · fastest of 50 · top 5 within 1.2s		+21.090squal +21.853s	123.0%qual 124.1%
No rule changes on record between these events
	Mid-Ohio Sports Car Course Runoffs 20162016-09-19	1:17.308James Devenport · fastest of 14 · top 5 within 2.7s	1:19.407Gianpaolo Ciancimino · fastest of 13 · top 5 within 1.8s		1:19.886Alex Mayer · fastest of 10 · top 5 within 1.5s	1:21.015Jeremy Hill · fastest of 10 · top 5 within 1.2s		+1.608squal +2.578s	102.0%qual 103.3%	1:35.439John Schmitt · fastest of 34 · top 5 within 1.5s	1:36.625Kevin Boehm · fastest of 31 · top 5 within 0.6s		+17.218squal +18.131s	121.7%qual 123.5%
No rule changes on record between these events
	Daytona International Speedway Runoffs 20152015-09-21	1:49.219Jim Downing · fastest of 9 · top 5 within 2.2s	1:49.792Gianpaolo Ciancimino · fastest of 10 · top 5 within 1.7s		1:50.711J R Osborne · fastest of 20 · top 5 within 1.1s	1:51.616J R Osborne · fastest of 19 · top 5 within 2.1s		+1.824squal +1.492s	101.7%qual 101.4%	2:09.672Kevin Boehm · fastest of 37 · top 5 within 2.5s	2:10.269Kevin Boehm · fastest of 37 · top 5 within 2.1s		+20.477squal +20.453s	118.7%qual 118.7%

By track

Track	Events	Typical % of P1	Best	Latest
Road America	4	100.0%2 of 4 with P1	100.0%Runoffs 2020	100.0%Runoffs 2024
Virginia International Raceway	3	100.0%	100.0%Runoffs 2019	100.0%Runoffs 2023
Indianapolis Motor Speedway	2	100.0%	100.0%Runoffs 2017	100.0%Runoffs 2021
Daytona International Speedway	1	100.0%	100.0%Runoffs 2015	100.0%Runoffs 2015
Mid-Ohio Sports Car Course	1	100.0%	100.0%Runoffs 2016	100.0%Runoffs 2016
Sonoma Raceway	1	100.0%	100.0%Runoffs 2018	100.0%Runoffs 2018

About this data

Every event the class ran, at any track, oldest to newest on the chart and newest first in the table. Each point is the class's best lap as a share of P1's best on the same day: the weather, the track and its configuration cancel out, so one figure compares across tracks and years where lap times cannot. It still moves when the yardstick's own balance changes or its field thins, and an event the yardstick did not run has no point. A best from fewer than three cars is greyed. The rule changes that took effect between two events are folded between their rows.