BoP Lab / World Wide Technology Raceway

STL vs FF vs FE2 pace at World Wide Technology Raceway

Quickest here: STL 1:07.622 Joe Moser, ADS 2020 race · FF 1:03.578 David H. Livingston Jr., ADS 2020 race · FE2 58.649 Scott Rettich, ADS 2020 qualifying

	Event	STL			FF					FE2
	Event	Qual best	Race best	Trap	Qual best	Race best	Trap	vs STL	% of STL	Qual best	Race best	Trap	vs STL	% of STL
	ADS 2020 ADS202020-05-29	1:07.837Joe Moser · fastest of 5 · top 5 within 4.0s	1:07.622Joe Moser · fastest of 5 · top 5 within 4.1s	127.0Joe Moser	1:05.120David H. Livingston Jr. · only car	1:03.578David H. Livingston Jr. · only car	129.3David H. Livingston Jr.	-4.044squal -2.717s	94.0%qual 96.0%	58.649Scott Rettich · fastest of 4 · top 4 within 2.3s	58.825Scott Rettich · fastest of 4 · top 4 within 3.9s	141.1Scott Rettich	-8.797squal -9.188s	87.0%qual 86.5%
23 earlier rule changes on record, in force before ADS 2020 (from 2019)6 induction · 3 cars added · 3 engine · 2 weight · 1 tyres & wheels · 8 wording · STL Honda B18 restrictor reduced from 54mm to 53mm flat plate; B18C1 added with 54mm restrictor. · FF alternator changes from not required to optional. · STU GM Ecotech LNF now allowed with turbo removed or with LE5 head and intake manifold, meeting STL specs. · STL Mazda MZR restrictor reduced from 54 mm to 53 mm. · STL Mazda MZR restrictor reduced from 55 mm to 53 mm. · FF allows Honda HPD LC1 low-cost ECU with lambda sensor; E1 ECU no longer supported but existing units permitted if sealed. · FF rain tyres now allow Hoosier W3 Radial in addition to existing Hoosier Wet option. · STL Mazda Spec MX5 Challenge adds approved wheel part numbers 0000-04-5706-GM, 0000-04-5706-SL. · FE and FE2 minimum weight increased to 1270 lbs including driver; spring options and tire warmer ban added. · Mazda Spec MX-5 Challenge classified in STL with 2000cc displacement and 2500 lbs minimum weight. · STU alternate intake manifolds now allowed case-by-case instead of prohibited. · STL Acura/Honda B18 except C engine restrictor increases from 53mm to 54mm flat plate. · STL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. · STL adds VW 1.8L R4 20VT 1781cc, 1 minimum weight, turbo removed permitted. · STL Mazda Renesis minimum weight reduced from 2800 to 2700 lbs. · STL Mazda MX-5 Cup brake pad compound changed to open. · STL adds Acura/Honda B18C1 GSR with 54mm flat plate restrictor and port matching limited to 1 inch. · STL Mazda 12 and 13B now permit port matching; previous ban removed. · FF Honda Fit permitted to use 0.25mm oversize pistons, cylinder honing increased to 73.315mm maximum. · FF heat shield rule clarified: thermal wrap allowed on manifold exterior if easily removable for inspection. · FF catch tank minimum capacity rules clarified: coolant catch tank now one U.S. pint minimum, oil catch tank one U.S. quart minimum. · STL B18C Type R variants get 54mm flat plate restrictor; B17 also gets 54mm restrictor. · STL Mazda Miata removes maximum displacement limit and adjusts minimum weight.showhide 2020-05-01 STL STL Honda B18 restrictor changes #28794inductionfasterSTL Honda B18 restrictor reduced from 54mm to 53mm flat plate; B18C1 added with 54mm restrictor. 2020-04-01 FF E&O FF Kent Engine alternator language #28204wordingwordingFF alternator changes from not required to optional. 2020-04-01 STL Change GM LNF 2.0 Allowance to LSJ Engine for Viable STL 2.0 #27884engineslowerSTU GM Ecotech LNF now allowed with turbo removed or with LE5 head and intake manifold, meeting STL specs. 2020-04-01 STL Acura/Honda B18C engine chart. Reduce the current 54 mm flat plat #28663inductionslowerSTL Mazda MZR restrictor reduced from 54 mm to 53 mm. 2020-04-01 STL Mazda MZR engine chart. Reduce the current 55 mm flat plate to 53 #28664inductionslowerSTL Mazda MZR restrictor reduced from 55 mm to 53 mm. 2020-03-01 FF Honda Racing HPD low cost ECU proposal #27563engineengineFF allows Honda HPD LC1 low-cost ECU with lambda sensor; E1 ECU no longer supported but existing units permitted if sealed. 2020-03-01 FF Update rain tire designation #28443tyres & wheelstyres & wheelsFF rain tyres now allow Hoosier W3 Radial in addition to existing Hoosier Wet option. 2020-03-01 STL Request to add wheel part numbers #28342wordingwordingSTL Mazda Spec MX5 Challenge adds approved wheel part numbers 0000-04-5706-GM, 0000-04-5706-SL. 2019-12-01 FE2 FE / FE2 Update Rules #27624weightslowerFE and FE2 minimum weight increased to 1270 lbs including driver; spring options and tire warmer ban added. 2019-10-01 STL Request to Classify Spec MX-5 Challenge in STL #27399cars addedcars addedMazda Spec MX-5 Challenge classified in STL with 2000cc displacement and 2500 lbs minimum weight. 2019-07-01 STL Request clarification for manifold and throttle in STU #27004inductionfasterSTU alternate intake manifolds now allowed case-by-case instead of prohibited. 2019-05-31 STL Request Restrictor Plate correction #26779inductionfasterSTL Acura/Honda B18 except C engine restrictor increases from 53mm to 54mm flat plate. 2019-05-01 STL Request Ride Height Clarification #26597wordingwordingSTL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. 2019-03-01 STL Request to Allow VW 1.8L Engine #25614cars addedcars addedSTL adds VW 1.8L R4 20VT 1781cc, 1 minimum weight, turbo removed permitted. 2019-03-01 STL Request to reduce weight of RX8 with Renesis rotary #25781weight -100 lbsfasterSTL Mazda Renesis minimum weight reduced from 2800 to 2700 lbs. 2019-03-01 STL Request for Open Brake Pads On Mazda MX-5 Cup NC #25821wordingwordingSTL Mazda MX-5 Cup brake pad compound changed to open. 2019-03-01 STL Request to clarify B18C1 GSR Honda B motor table #26209cars addedcars addedSTL adds Acura/Honda B18C1 GSR with 54mm flat plate restrictor and port matching limited to 1 inch. 2019-03-01 STL Port Matching #26415wordingfasterSTL Mazda 12 and 13B now permit port matching; previous ban removed. 2019-02-01 FF Request for Oversize Honda Fit Pistons #25810enginefasterFF Honda Fit permitted to use 0.25mm oversize pistons, cylinder honing increased to 73.315mm maximum. 2019-02-01 FF Heat Shield - Fit Intake #26102wordingwordingFF heat shield rule clarified: thermal wrap allowed on manifold exterior if easily removable for inspection. 2019-02-01 FF Request catch cans/tanks clarification #26158wordingwordingFF catch tank minimum capacity rules clarified: coolant catch tank now one U.S. pint minimum, oil catch tank one U.S. quart minimum. 2019-01-01 STL Request to equalize FPR Reduction on all B-Series Vtec Engines #24746inductionslowerSTL B18C Type R variants get 54mm flat plate restrictor; B17 also gets 54mm restrictor. 2019-01-01 STL Request E&O for Mazda Miata Spec Line #25955wordingunclearSTL Mazda Miata removes maximum displacement limit and adjusts minimum weight.

Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. "% of STL" is the class's best as a share of STL's best at the same event (100% is level, less is quicker): weather and track condition move every class together, so this compares across years where the raw times do not. It still breaks when STL's own field changes or one session was wet and another dry. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.