BoP Lab / Laguna Seca

STL vs FB vs FV vs AS pace at Laguna Seca

Quickest here: STL 1:42.330 Tim Auger, Hoosier SCCA Super Tour (San Francisco Region) race · FB 1:24.666 Jake Latham, Hoosier SCCA Super Tour (San Francisco Region) qualifying · FV 1:48.104 Dennis Andrade, Hoosier SCCA Super Tour (San Francisco Region) qualifying · AS 1:40.712 Clark Nunes, Hoosier SCCA Super Tour (San Francisco Region) qualifying

	Event	STL			FB					FV					AS
	Event	Qual best	Race best	Trap	Qual best	Race best	Trap	vs STL	% of STL	Qual best	Race best	Trap	vs STL	% of STL	Qual best	Race best	Trap	vs STL	% of STL
	Hoosier SCCA Super Tour (San Francisco Region) ST19JUL262019-07-26	1:42.773Tim Auger · fastest of 7 · top 5 within 4.9s	1:42.330Tim Auger · fastest of 6 · top 5 within 4.5s	95.7Thomas Lepper	1:24.666Jake Latham · only car	1:25.752Jake Latham · only car	116.0Jake Latham	-16.578squal -18.107s	83.8%qual 82.4%	1:48.104Dennis Andrade · fastest of 7 · top 5 within 3.8s	1:49.588Dennis Andrade · fastest of 7 · top 5 within 1.4s	88.2Dennis Andrade	+7.258squal +5.331s	107.1%qual 105.2%	1:40.712Clark Nunes · fastest of 4 · top 4 within 7.9s	1:40.914Clark Nunes · fastest of 4 · top 4 within 8.0s	103.0Michael Thompson	-1.416squal -2.061s	98.6%qual 98.0%
16 earlier rule changes on record, in force before Hoosier SCCA Super Tour (San Francisco Region) (from 2019)3 cars added · 3 induction · 3 weight · 1 aero · 6 wording · STU alternate intake manifolds now allowed case-by-case instead of prohibited. · FV exhaust opening can now extend to 4 inches behind body rear, previously 3 inches maximum. · STL Acura/Honda B18 except C engine restrictor increases from 53mm to 54mm flat plate. · FV front track maximum 52.500" and rear track 49.125"-50.750" no longer prohibits spacers. · STL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. · FV disc brake assembly minimum weight clarified to 16.5 lbs total; caliper minimum weight requirement removed. · STL adds VW 1.8L R4 20VT 1781cc, 1 minimum weight, turbo removed permitted. · STL Mazda Renesis minimum weight reduced from 2800 to 2700 lbs. · STL Mazda MX-5 Cup brake pad compound changed to open. · STL adds Acura/Honda B18C1 GSR with 54mm flat plate restrictor and port matching limited to 1 inch. · STL Mazda 12 and 13B now permit port matching; previous ban removed. · FV intake manifold horizontal tube measurement locations clarified between 1.500" and 8.000" on short side. · STL B18C Type R variants get 54mm flat plate restrictor; B17 also gets 54mm restrictor. · STL Mazda Miata removes maximum displacement limit and adjusts minimum weight.showhide 2019-07-01 STL Request clarification for manifold and throttle in STU #27004inductionfaster · inductionSTU alternate intake manifolds now allowed case-by-case instead of prohibited. 2019-05-31 AS Request to Revert to 2017 Weights #25885weight 2019-05-31 FV Exhaust termination rule E&O #26702aeroaeroFV exhaust opening can now extend to 4 inches behind body rear, previously 3 inches maximum. 2019-05-31 STL Request Restrictor Plate correction #26779inductionfaster · inductionSTL Acura/Honda B18 except C engine restrictor increases from 53mm to 54mm flat plate. 2019-05-01 FV E&O Dimensions #26674wordingwordingFV front track maximum 52.500" and rear track 49.125"-50.750" no longer prohibits spacers. 2019-05-01 STL Request Ride Height Clarification #26597wordingwordingSTL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. 2019-04-01 FV Request to clarify Disc Brake rules bearing retainer & weights #26262weightslower · weightFV disc brake assembly minimum weight clarified to 16.5 lbs total; caliper minimum weight requirement removed. 2019-03-01 STL Request to Allow VW 1.8L Engine #25614cars addedcars addedSTL adds VW 1.8L R4 20VT 1781cc, 1 minimum weight, turbo removed permitted. 2019-03-01 STL Request to reduce weight of RX8 with Renesis rotary #25781weight -100 lbsfaster · weightSTL Mazda Renesis minimum weight reduced from 2800 to 2700 lbs. 2019-03-01 STL Request for Open Brake Pads On Mazda MX-5 Cup NC #25821wordingwordingSTL Mazda MX-5 Cup brake pad compound changed to open. 2019-03-01 STL Request to clarify B18C1 GSR Honda B motor table #26209cars addedcars addedSTL adds Acura/Honda B18C1 GSR with 54mm flat plate restrictor and port matching limited to 1 inch. 2019-03-01 STL Port Matching #26415wordingfasterSTL Mazda 12 and 13B now permit port matching; previous ban removed. 2019-02-01 AS SMG Mustang eligibility in American sedan #26224cars added 2019-02-01 FV FV Intake Manifold Clarification #26008wordingwordingFV intake manifold horizontal tube measurement locations clarified between 1.500" and 8.000" on short side. 2019-01-01 STL Request to equalize FPR Reduction on all B-Series Vtec Engines #24746inductionslower · inductionSTL B18C Type R variants get 54mm flat plate restrictor; B17 also gets 54mm restrictor. 2019-01-01 STL Request E&O for Mazda Miata Spec Line #25955wordingunclearSTL Mazda Miata removes maximum displacement limit and adjusts minimum weight.

Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. "% of STL" is the class's best as a share of STL's best at the same event (100% is level, less is quicker): weather and track condition move every class together, so this compares across years where the raw times do not. It still breaks when STL's own field changes or one session was wet and another dry. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.