BoP Lab / Laguna Seca

P1 vs AS vs FB vs STL pace at Laguna Seca

Quickest here: P1 1:21.626 Jim Devenport, Super Tour Jul 2019 qualifying · AS 1:40.712 Clark Nunes, Super Tour Jul 2019 qualifying · FB 1:24.666 Jake Latham, Super Tour Jul 2019 qualifying · STL 1:42.330 Tim Auger, Super Tour Jul 2019 race

	Event	P1			AS					FB					STL
	Event	Qual best	Race best	Trap	Qual best	Race best	Trap	vs P1	% of P1	Qual best	Race best	Trap	vs P1	% of P1	Qual best	Race best	Trap	vs P1	% of P1
	Super Tour Jul 2019 ST19JUL262019-07-26	1:21.626Jim Devenport · fastest of 6 · top 5 within 5.2s	1:21.922Todd Slusher · fastest of 6 · top 5 within 4.1s	121.3John Manfroy	1:40.712Clark Nunes · fastest of 4 · top 4 within 7.9s	1:40.914Clark Nunes · fastest of 4 · top 4 within 8.0s	103.0Michael Thompson	+18.992squal +19.086s	123.2%qual 123.4%	1:24.666Jake Latham · only car	1:25.752Jake Latham · only car	116.0Jake Latham	+3.830squal +3.040s	104.7%qual 103.7%	1:42.773Tim Auger · fastest of 7 · top 5 within 4.9s	1:42.330Tim Auger · fastest of 6 · top 5 within 4.5s	95.7Thomas Lepper	+20.408squal +21.147s	124.9%qual 125.9%
25 earlier rule changes on record, in force before Super Tour Jul 2019 (from 2019)4 cars added · 3 engine · 2 weight · 13 wording · 3 other · P1 permits mechanical, solenoid, and air-shifters; prohibits electronic pre-selection and multi-wheel power. · P1 minimum bodywork height rule moved and restated with new 115cm aerodynamic part height limit. · P1 consolidates fender louver rules into one section; removes duplicate allowance for louvers and clarifies brake and engine air ducts are permitted. · STU allows alternate intake manifolds on case-by-case basis; stock throttle device and manifold otherwise required. · AS Ford Mustang 79-93 non-Cobra drops 100 lbs to 3150; over 313 CID Cobra drops 100 lbs to 3450. · P1 anti-intrusion panels now allowed anywhere on chassis sides instead of specified locations. · P1 bodywork wording clarified: comfort and safety for driver and passenger or driver only. · STL Acura/Honda B18 except C engine restrictor increased from 53mm to 54mm flat plate. · P1 Engine Table reference cleaned up; no performance change. · P1 Mazda Renesis Rotary engine spec line removed from Engine Table. · STL and STU ride height measurement clarified: lowest rocker panel point without driver, excluding pinch weld. · P1 Staudacher and Honda K20A-FD2 engine table wording clarified; no performance change. · P1 closed cockpit single-seat cars remain prohibited; rule moved from subsection J.5 to B.4. · STL adds VW 1.8L R4 20VT 1781 cc, 1781 minimum weight, naturally aspirated only. · STL Mazda Renesis minimum weight reduced to 2700 lbs. · STL Mazda MX-5 Cup brake pad compound now open. · STL adds Acura/Honda B18C1 GSR with 1797cc displacement, 54mm flat plate restrictor required, porting outside 1" allowance prohibited. · STL Mazda 12 and 13B now permit port matching; porting ban removed. · AS adds Spec Mustang SMG classification with 107.1 wheelbase, 3.73 gears, 355mm front and 300mm rear brakes. · P1 engine table reference corrected from 'above' to 'below'; ETC/FBW/DBW throttle wording clarified on sensor and fail-safe requirements. · P1 removes TIR inlet restrictor option; deletes requirement for single turbo/supercharger unit with single restrictor. · P1 CN-spec Honda K20A-FD2 clarified: stock OEM parts required, no machining allowed. · P1 engine rules correct grammar and remove head designs from specification table. · STL B17 now requires 54mm flat plate restrictor; B18C Type R variants move to 54mm restrictor, weight chart baseline. · STL Mazda Miata removes maximum displacement limit; minimum weight corrected to unspecified figure.showhide 2019-07-01 P1 E&O Transmissions #27005otheraddedP1 permits mechanical, solenoid, and air-shifters; prohibits electronic pre-selection and multi-wheel power. 2019-07-01 P1 Move minimum height provision to #27031wordingwordingP1 minimum bodywork height rule moved and restated with new 115cm aerodynamic part height limit. 2019-07-01 P1 Remove duplicative fender louver provision #27033wordingwordingP1 consolidates fender louver rules into one section; removes duplicate allowance for louvers and clarifies brake and engine air ducts are permitted. 2019-07-01 STL Request clarification for manifold and throttle in STU #27004wordingwordingSTU allows alternate intake manifolds on case-by-case basis; stock throttle device and manifold otherwise required. 2019-05-31 AS Request to Revert to 2017 Weights #25885weightfaster · weightAS Ford Mustang 79-93 non-Cobra drops 100 lbs to 3150; over 313 CID Cobra drops 100 lbs to 3450. 2019-05-31 P1 Missing word E&O #26919wordingwordingP1 anti-intrusion panels now allowed anywhere on chassis sides instead of specified locations. 2019-05-31 P1 E&O correction to GCR 9.1.8.C.C. #26927wordingwordingP1 bodywork wording clarified: comfort and safety for driver and passenger or driver only. 2019-05-31 STL Request Restrictor Plate correction #26779enginefaster · engineSTL Acura/Honda B18 except C engine restrictor increased from 53mm to 54mm flat plate. 2019-05-01 P1 Clean up reference to engine table #26648wordingwordingP1 Engine Table reference cleaned up; no performance change. 2019-05-01 P1 Remove redundant spec line #26692cars addedremoved · cars addedP1 Mazda Renesis Rotary engine spec line removed from Engine Table. 2019-05-01 STL Request Ride Height Clarification #26597wordingwordingSTL and STU ride height measurement clarified: lowest rocker panel point without driver, excluding pinch weld. 2019-04-01 P1 Clean Up Engine Table Language #26590wordingwordingP1 Staudacher and Honda K20A-FD2 engine table wording clarified; no performance change. 2019-03-01 P1 Move single-seat closed cockpit provision to #26376wordingwordingP1 closed cockpit single-seat cars remain prohibited; rule moved from subsection J.5 to B.4. 2019-03-01 STL Request to Allow VW 1.8L Engine #25614cars addedaddedSTL adds VW 1.8L R4 20VT 1781 cc, 1781 minimum weight, naturally aspirated only. 2019-03-01 STL Request to reduce weight of RX8 with Renesis rotary #25781weight -100 lbsfaster · weightSTL Mazda Renesis minimum weight reduced to 2700 lbs. 2019-03-01 STL Request for Open Brake Pads On Mazda MX-5 Cup NC #25821otheraddedSTL Mazda MX-5 Cup brake pad compound now open. 2019-03-01 STL Request to clarify B18C1 GSR Honda B motor table #26209cars addedaddedSTL adds Acura/Honda B18C1 GSR with 1797cc displacement, 54mm flat plate restrictor required, porting outside 1" allowance prohibited. 2019-03-01 STL Port Matching #26415enginefaster · engineSTL Mazda 12 and 13B now permit port matching; porting ban removed. 2019-02-01 AS SMG Mustang eligibility in American sedan #26224cars addedaddedAS adds Spec Mustang SMG classification with 107.1 wheelbase, 3.73 gears, 355mm front and 300mm rear brakes. 2019-02-01 P1 Correct errors in GCR section 9.1.8.C.J #26144wordingwordingP1 engine table reference corrected from 'above' to 'below'; ETC/FBW/DBW throttle wording clarified on sensor and fail-safe requirements. 2019-01-01 P1 Remove redundant inlet restrictor provisions #25877wordingwordingP1 removes TIR inlet restrictor option; deletes requirement for single turbo/supercharger unit with single restrictor. 2019-01-01 P1 Clarify Honda K20A-FD2 parts requirement #25949wordingwordingP1 CN-spec Honda K20A-FD2 clarified: stock OEM parts required, no machining allowed. 2019-01-01 P1 Correct GCR section 9.1.8.C.J errors #25966wordingwordingP1 engine rules correct grammar and remove head designs from specification table. 2019-01-01 STL Request to equalize FPR Reduction on all B-Series Vtec Engines #24746enginefaster · engineSTL B17 now requires 54mm flat plate restrictor; B18C Type R variants move to 54mm restrictor, weight chart baseline. 2019-01-01 STL Request E&O for Mazda Miata Spec Line #25955otherunclearSTL Mazda Miata removes maximum displacement limit; minimum weight corrected to unspecified figure.

About this data

Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. "% of P1" is the class's best as a share of P1's best at the same event (100% is level, less is quicker): weather and track condition move every class together, so this compares across years where the raw times do not. It still breaks when P1's own field changes or one session was wet and another dry. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.