BoP Lab / Laguna Seca

GT1 vs STL vs P1 pace at Laguna Seca

Quickest here: STL 1:42.330 Tim Auger, Hoosier SCCA Super Tour (San Francisco Region) race · P1 1:21.626 Jim Devenport, Hoosier SCCA Super Tour (San Francisco Region) qualifying

	Event	GT1			STL				P1
	Event	Qual best	Race best	Trap	Qual best	Race best	Trap	vs GT1	Qual best	Race best	Trap	vs GT1
	Hoosier SCCA Super Tour (San Francisco Region) ST19JUL262019-07-26				1:42.773Tim Auger · fastest of 7 · top 5 within 4.9s	1:42.330Tim Auger · fastest of 6 · top 5 within 4.5s	95.7Thomas Lepper		1:21.626Jim Devenport · fastest of 6 · top 5 within 5.2s	1:21.922Todd Slusher · fastest of 6 · top 5 within 4.1s	121.3John Manfroy
28 earlier rule changes on record, in force before Hoosier SCCA Super Tour (San Francisco Region) (from 2019)4 cars added · 4 induction · 1 aero · 1 removed · 1 weight · 17 wording · GT1 allows Trans Am rear wing, 12" chord, 72" span, 1/2" wicker, 100 sq in endplates, no weight penalty. · P1 allows mechanical and solenoid shifters, prohibits electronic controls and pre-selected changes. · P1 bodywork minimum height provision moved to aerodynamic section; 115cm height limit for aero parts added. · P1 clarifies fender louver and brake duct rules, consolidating duplicative provisions in GCR 9.1.8.C. · STU alternate intake manifolds now allowed case-by-case instead of prohibited. · P1 anti-intrusion panels now allowed anywhere on chassis sides, previously restricted. · P1 bodywork wording corrected: 'a passenger' becomes 'passenger' in three GCR sections. · STL Acura/Honda B18 except C engine restrictor increases from 53mm to 54mm flat plate. · GTX tube frame cars gain fuel injection with 90mm maximum throttle body size. · Ligier JS2 R classified in GTX, no performance parameters specified in filing. · P1 Engine Table reference cleaned up; no performance change. · P1 Mazda Renesis Rotary removed from Engine Table specification line. · STL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. · GT1 and GT2/GT3/LITE ride height requirements removed from GCR sections 9.1.2.D.5.a.1 and 9.1.2.F.7.b. · P1 Staudacher and Honda K20A-FD2 engine table language cleaned up; no performance changes. · P1 closed cockpit single-seat cars moved from subsection J.5 to subsection B.4; prohibition unchanged. · STL adds VW 1.8L R4 20VT 1781cc, 1 minimum weight, turbo removed permitted. · STL Mazda Renesis minimum weight reduced from 2800 to 2700 lbs. · STL Mazda MX-5 Cup brake pad compound changed to open. · STL adds Acura/Honda B18C1 GSR with 54mm flat plate restrictor and port matching limited to 1 inch. · STL Mazda 12 and 13B now permit port matching; previous ban removed. · P1 engine table reference corrected from 'above' to 'below'; ECU throttle wording clarified for dual sensors and fail-safes. · GTX FIA GT3: Audi R8 40mm restrictor 2900 lbs, BMW Z4 70mm 2800 lbs, Ferrari 488 35mm restrictor 3025 lbs classified. · P1 removes redundant TIR inlet restrictor provisions; SIR and flat plate restrictors remain required. · P1 Honda K20A-FD2 CN-spec clarifies allowed parts to OEM list only, no machining. · P1 engine table wording corrected; head designs removed from listed specifications. · STL B18C Type R variants get 54mm flat plate restrictor; B17 also gets 54mm restrictor. · STL Mazda Miata removes maximum displacement limit and adjusts minimum weight.showhide 2019-07-01 GT1 Clarify Trans Am Legal Bodywork and Wing #26953aerofasterGT1 allows Trans Am rear wing, 12" chord, 72" span, 1/2" wicker, 100 sq in endplates, no weight penalty. 2019-07-01 P1 E&O Transmissions #27005wordingwordingP1 allows mechanical and solenoid shifters, prohibits electronic controls and pre-selected changes. 2019-07-01 P1 Move minimum height provision to #27031wordingwordingP1 bodywork minimum height provision moved to aerodynamic section; 115cm height limit for aero parts added. 2019-07-01 P1 Remove duplicative fender louver provision #27033wordingwordingP1 clarifies fender louver and brake duct rules, consolidating duplicative provisions in GCR 9.1.8.C. 2019-07-01 STL Request clarification for manifold and throttle in STU #27004inductionfasterSTU alternate intake manifolds now allowed case-by-case instead of prohibited. 2019-05-31 P1 Missing word E&O #26919wordingwordingP1 anti-intrusion panels now allowed anywhere on chassis sides, previously restricted. 2019-05-31 P1 E&O correction to GCR 9.1.8.C.C. #26927wordingwordingP1 bodywork wording corrected: 'a passenger' becomes 'passenger' in three GCR sections. 2019-05-31 STL Request Restrictor Plate correction #26779inductionfasterSTL Acura/Honda B18 except C engine restrictor increases from 53mm to 54mm flat plate. 2019-05-01 GT1 Request GTX Fuel injection for previous GT-1 tube frame cars #26141inductionfasterGTX tube frame cars gain fuel injection with 90mm maximum throttle body size. 2019-05-01 GT1 Request to Classify Ligier JS2 R #26535cars addedcars addedLigier JS2 R classified in GTX, no performance parameters specified in filing. 2019-05-01 P1 Clean up reference to engine table #26648wordingwordingP1 Engine Table reference cleaned up; no performance change. 2019-05-01 P1 Remove redundant spec line #26692removedremovedP1 Mazda Renesis Rotary removed from Engine Table specification line. 2019-05-01 STL Request Ride Height Clarification #26597wordingwordingSTL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. 2019-04-01 GT1 Request Ride Height Clarification #26600wordingwordingGT1 and GT2/GT3/LITE ride height requirements removed from GCR sections 9.1.2.D.5.a.1 and 9.1.2.F.7.b. 2019-04-01 P1 Clean Up Engine Table Language #26590wordingwordingP1 Staudacher and Honda K20A-FD2 engine table language cleaned up; no performance changes. 2019-03-01 P1 Move single-seat closed cockpit provision to #26376wordingwordingP1 closed cockpit single-seat cars moved from subsection J.5 to subsection B.4; prohibition unchanged. 2019-03-01 STL Request to Allow VW 1.8L Engine #25614cars addedcars addedSTL adds VW 1.8L R4 20VT 1781cc, 1 minimum weight, turbo removed permitted. 2019-03-01 STL Request to reduce weight of RX8 with Renesis rotary #25781weight -100 lbsfasterSTL Mazda Renesis minimum weight reduced from 2800 to 2700 lbs. 2019-03-01 STL Request for Open Brake Pads On Mazda MX-5 Cup NC #25821wordingwordingSTL Mazda MX-5 Cup brake pad compound changed to open. 2019-03-01 STL Request to clarify B18C1 GSR Honda B motor table #26209cars addedcars addedSTL adds Acura/Honda B18C1 GSR with 54mm flat plate restrictor and port matching limited to 1 inch. 2019-03-01 STL Port Matching #26415wordingfasterSTL Mazda 12 and 13B now permit port matching; previous ban removed. 2019-02-01 P1 Correct errors in GCR section 9.1.8.C.J #26144wordingwordingP1 engine table reference corrected from 'above' to 'below'; ECU throttle wording clarified for dual sensors and fail-safes. 2019-01-01 GT1 GTX Homologation table update #26034cars addedcars addedGTX FIA GT3: Audi R8 40mm restrictor 2900 lbs, BMW Z4 70mm 2800 lbs, Ferrari 488 35mm restrictor 3025 lbs classified. 2019-01-01 P1 Remove redundant inlet restrictor provisions #25877wordingwordingP1 removes redundant TIR inlet restrictor provisions; SIR and flat plate restrictors remain required. 2019-01-01 P1 Clarify Honda K20A-FD2 parts requirement #25949wordingwordingP1 Honda K20A-FD2 CN-spec clarifies allowed parts to OEM list only, no machining. 2019-01-01 P1 Correct GCR section 9.1.8.C.J errors #25966wordingwordingP1 engine table wording corrected; head designs removed from listed specifications. 2019-01-01 STL Request to equalize FPR Reduction on all B-Series Vtec Engines #24746inductionslowerSTL B18C Type R variants get 54mm flat plate restrictor; B17 also gets 54mm restrictor. 2019-01-01 STL Request E&O for Mazda Miata Spec Line #25955wordingunclearSTL Mazda Miata removes maximum displacement limit and adjusts minimum weight.

Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.