BoP Lab / Laguna Seca

GT1 vs STL vs FM vs FF pace at Laguna Seca

Quickest here: STL 1:42.330 Tim Auger, Hoosier SCCA Super Tour (San Francisco Region) race · FM 1:31.060 Bill Weaver, Hoosier SCCA Super Tour (San Francisco Region) qualifying · FF 1:34.290 Chuck Horn, Hoosier SCCA Super Tour (San Francisco Region) qualifying

	Event	GT1			STL				FM				FF
	Event	Qual best	Race best	Trap	Qual best	Race best	Trap	vs GT1	Qual best	Race best	Trap	vs GT1	Qual best	Race best	Trap	vs GT1
	Hoosier SCCA Super Tour (San Francisco Region) ST19JUL262019-07-26				1:42.773Tim Auger · fastest of 7 · top 5 within 4.9s	1:42.330Tim Auger · fastest of 6 · top 5 within 4.5s	95.7Thomas Lepper		1:31.060Bill Weaver · fastest of 7 · top 5 within 3.0s	1:32.101Bill Weaver · fastest of 7 · top 5 within 1.0s	109.0Randy Sturgeon		1:34.290Chuck Horn · fastest of 7 · top 5 within 1.8s	1:35.120Courtney Crone · fastest of 7 · top 5 within 1.6s	104.0Chuck Horn
18 earlier rule changes on record, in force before Hoosier SCCA Super Tour (San Francisco Region) (from 2019)4 cars added · 4 induction · 1 aero · 1 engine · 1 weight · 7 wording · GT1 allows Trans Am rear wing, 12" chord, 72" span, 1/2" wicker, 100 sq in endplates, no weight penalty. · STU alternate intake manifolds now allowed case-by-case instead of prohibited. · STL Acura/Honda B18 except C engine restrictor increases from 53mm to 54mm flat plate. · GTX tube frame cars gain fuel injection with 90mm maximum throttle body size. · Ligier JS2 R classified in GTX, no performance parameters specified in filing. · STL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. · GT1 and GT2/GT3/LITE ride height requirements removed from GCR sections 9.1.2.D.5.a.1 and 9.1.2.F.7.b. · STL adds VW 1.8L R4 20VT 1781cc, 1 minimum weight, turbo removed permitted. · STL Mazda Renesis minimum weight reduced from 2800 to 2700 lbs. · STL Mazda MX-5 Cup brake pad compound changed to open. · STL adds Acura/Honda B18C1 GSR with 54mm flat plate restrictor and port matching limited to 1 inch. · STL Mazda 12 and 13B now permit port matching; previous ban removed. · FF Honda Fit permitted to use 0.25mm oversize pistons, cylinder honing increased to 73.315mm maximum. · FF heat shield rule clarified: thermal wrap allowed on manifold exterior if easily removable for inspection. · FF catch tank minimum capacity rules clarified: coolant catch tank now one U.S. pint minimum, oil catch tank one U.S. quart minimum. · GTX FIA GT3: Audi R8 40mm restrictor 2900 lbs, BMW Z4 70mm 2800 lbs, Ferrari 488 35mm restrictor 3025 lbs classified. · STL B18C Type R variants get 54mm flat plate restrictor; B17 also gets 54mm restrictor. · STL Mazda Miata removes maximum displacement limit and adjusts minimum weight.showhide 2019-07-01 GT1 Clarify Trans Am Legal Bodywork and Wing #26953aerofasterGT1 allows Trans Am rear wing, 12" chord, 72" span, 1/2" wicker, 100 sq in endplates, no weight penalty. 2019-07-01 STL Request clarification for manifold and throttle in STU #27004inductionfasterSTU alternate intake manifolds now allowed case-by-case instead of prohibited. 2019-05-31 STL Request Restrictor Plate correction #26779inductionfasterSTL Acura/Honda B18 except C engine restrictor increases from 53mm to 54mm flat plate. 2019-05-01 GT1 Request GTX Fuel injection for previous GT-1 tube frame cars #26141inductionfasterGTX tube frame cars gain fuel injection with 90mm maximum throttle body size. 2019-05-01 GT1 Request to Classify Ligier JS2 R #26535cars addedcars addedLigier JS2 R classified in GTX, no performance parameters specified in filing. 2019-05-01 STL Request Ride Height Clarification #26597wordingwordingSTL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. 2019-04-01 GT1 Request Ride Height Clarification #26600wordingwordingGT1 and GT2/GT3/LITE ride height requirements removed from GCR sections 9.1.2.D.5.a.1 and 9.1.2.F.7.b. 2019-03-01 STL Request to Allow VW 1.8L Engine #25614cars addedcars addedSTL adds VW 1.8L R4 20VT 1781cc, 1 minimum weight, turbo removed permitted. 2019-03-01 STL Request to reduce weight of RX8 with Renesis rotary #25781weight -100 lbsfasterSTL Mazda Renesis minimum weight reduced from 2800 to 2700 lbs. 2019-03-01 STL Request for Open Brake Pads On Mazda MX-5 Cup NC #25821wordingwordingSTL Mazda MX-5 Cup brake pad compound changed to open. 2019-03-01 STL Request to clarify B18C1 GSR Honda B motor table #26209cars addedcars addedSTL adds Acura/Honda B18C1 GSR with 54mm flat plate restrictor and port matching limited to 1 inch. 2019-03-01 STL Port Matching #26415wordingfasterSTL Mazda 12 and 13B now permit port matching; previous ban removed. 2019-02-01 FF Request for Oversize Honda Fit Pistons #25810enginefasterFF Honda Fit permitted to use 0.25mm oversize pistons, cylinder honing increased to 73.315mm maximum. 2019-02-01 FF Heat Shield - Fit Intake #26102wordingwordingFF heat shield rule clarified: thermal wrap allowed on manifold exterior if easily removable for inspection. 2019-02-01 FF Request catch cans/tanks clarification #26158wordingwordingFF catch tank minimum capacity rules clarified: coolant catch tank now one U.S. pint minimum, oil catch tank one U.S. quart minimum. 2019-01-01 GT1 GTX Homologation table update #26034cars addedcars addedGTX FIA GT3: Audi R8 40mm restrictor 2900 lbs, BMW Z4 70mm 2800 lbs, Ferrari 488 35mm restrictor 3025 lbs classified. 2019-01-01 STL Request to equalize FPR Reduction on all B-Series Vtec Engines #24746inductionslowerSTL B18C Type R variants get 54mm flat plate restrictor; B17 also gets 54mm restrictor. 2019-01-01 STL Request E&O for Mazda Miata Spec Line #25955wordingunclearSTL Mazda Miata removes maximum displacement limit and adjusts minimum weight.

Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.