BoP Lab / Laguna Seca

GT1 vs P2 vs STU pace at Laguna Seca

Quickest here: P2 1:26.231 Chuck Bona, Hoosier SCCA Super Tour (San Francisco Region) race · STU 1:39.256 David Fiorelli, Hoosier SCCA Super Tour (San Francisco Region) qualifying

	Event	GT1			P2				STU
	Event	Qual best	Race best	Trap	Qual best	Race best	Trap	vs GT1	Qual best	Race best	Trap	vs GT1
	Hoosier SCCA Super Tour (San Francisco Region) ST19JUL262019-07-26				1:26.927Tim Day Jr · fastest of 5 · top 5 within 7.8s	1:26.231Chuck Bona · fastest of 7 · top 5 within 6.8s	116.8Tim Day Jr		1:39.256David Fiorelli · fastest of 3 · top 3 within 3.9s	1:41.478Nathan Pope · fastest of 3 · top 3 within 2.9s	104.9David Fiorelli
33 earlier rule changes on record, in force before Hoosier SCCA Super Tour (San Francisco Region) (from 2019)8 induction · 6 cars added · 3 aero · 3 engine · 1 tyres & wheels · 1 weight · 10 wording · 1 other · GT1 allows Trans Am rear wing, 12" chord, 72" span, 1/2" wicker, 100 sq in endplates, no weight penalty. · P2 cars limited to power application on maximum two wheels, effective 2019-07-01. · STU Nissan SR20DET removes -2mm penalty in Table B. · STU alternate intake manifolds now allowed case-by-case instead of prohibited. · P2 Enterprise minimum weight increases to 1375 lbs; peak horsepower of sealed ESR engine reduced per CRB specification. · STU aftermarket side skirts must meet 3-inch ride height, no openings except jacks or side exhaust, no wider than fascias, not higher than door bottom, no chassis reinforcement. · STU fender flare wording clarified: each fender may be flared up to 2" for tire clearance with 1% weight penalty. · GTX tube frame cars gain fuel injection with 90mm maximum throttle body size. · Ligier JS2 R classified in GTX, no performance parameters specified in filing. · STL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. · GT1 and GT2/GT3/LITE ride height requirements removed from GCR sections 9.1.2.D.5.a.1 and 9.1.2.F.7.b. · STU Mazda 13B Bridge Port may use ELITE ROTARY SHOP FD V2.0 intake manifold instead of stock. · STU Mazda MZR LF/L3/L5 may use Goodwin Part #61-2510 intake manifold with stock or Acura throttle body. · STU suspension rules clarified: alternate components from same manufacturer moved from section E to section D. · STU Honda/Acura B20 classified at 1973 cc, now permits VTEC B16 or B18 cylinder head and intake manifold. · STU flared fenders up to 2" with 1% weight penalty moved from base to Advanced Aero rules. · TCA Honda Civic Si (2017-) must run 37mm TIR maximum as of June 1, 2019. · STU BMW S54B32 OEM reclassified from E46 designation, 3246 cc, 3300 lbs minimum weight. · P2 stock engine restrictor shrinks to 35.0mm and weight rises to 1025 lbs; modified engine restrictor to 34.0mm, weight to 1125 lbs; line B.5 restrictor to 33.0mm, weight to 1185 lbs. · P2 Line A.1 restrictor reduced from 40mm to 38mm. · Honda Civic Si 2017- classified STU at 1500cc, 2800 lbs minimum with OEM engine and bodywork. · STU BMW E46 S54 OEM 3246cc added at 3300 lbs minimum weight, no Super Touring allowances. · STU Mazda 13B and 13B Bridge Port may use RE or REW housings and intake with turbo removed. · STU Honda K24 may use intake part #s 17100-RRB-A00 or 17100-PRB-A10. · STU Mazda 12A Bridge Port engine classified at 2550 lbs minimum weight with specified carburetor induction options. · STU World Challenge car weight calculation method removed; new basis unclear from text provided. · STU AWD cars no longer required to reduce restrictor 1 mm from table. · STU rear wing maximum cord length set to 12 inches, end plates to 72.0 square inches each. · GTX FIA GT3: Audi R8 40mm restrictor 2900 lbs, BMW Z4 70mm 2800 lbs, Ferrari 488 35mm restrictor 3025 lbs classified. · P2 Spec Line cars now allow 1345cc Hayabusa stock engines at 1050 lbs with 30mm restrictor. · P2 Group CN Honda K20A-FD2 55mm restrictor implementation delayed from 1/1/2019 to 3/1/2019. · P2 Honda K20A-FD2 in CN chassis must use stock intake manifold with 64mm throttle body and 55mm restrictor at 1500 lbs minimum weight. · STU Honda K20C1 Turbo I4 1996cc added at 3025 lbs minimum weight with 36mm TIR.showhide 2019-07-01 GT1 Clarify Trans Am Legal Bodywork and Wing #26953aerofasterGT1 allows Trans Am rear wing, 12" chord, 72" span, 1/2" wicker, 100 sq in endplates, no weight penalty. 2019-07-01 P2 E&O Transmissions #27006otherslowerP2 cars limited to power application on maximum two wheels, effective 2019-07-01. 2019-07-01 STU Remove -2mm penalty from SR20DET Nissan #26982enginefasterSTU Nissan SR20DET removes -2mm penalty in Table B. 2019-07-01 STU Request clarification for manifold and throttle in STU #27004inductionfasterSTU alternate intake manifolds now allowed case-by-case instead of prohibited. 2019-06-01 P2 Request to restrict all cars #26246weightslowerP2 Enterprise minimum weight increases to 1375 lbs; peak horsepower of sealed ESR engine reduced per CRB specification. 2019-05-31 STU Request to clarify afterrmarket side skirts exhaust exit #26814wordingwordingSTU aftermarket side skirts must meet 3-inch ride height, no openings except jacks or side exhaust, no wider than fascias, not higher than door bottom, no chassis reinforcement. 2019-05-31 STU Wheel Flare wording #26872wordingwordingSTU fender flare wording clarified: each fender may be flared up to 2" for tire clearance with 1% weight penalty. 2019-05-01 GT1 Request GTX Fuel injection for previous GT-1 tube frame cars #26141inductionfasterGTX tube frame cars gain fuel injection with 90mm maximum throttle body size. 2019-05-01 GT1 Request to Classify Ligier JS2 R #26535cars addedcars addedLigier JS2 R classified in GTX, no performance parameters specified in filing. 2019-05-01 STU Request Ride Height Clarification #26597wordingwordingSTL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. 2019-04-01 GT1 Request Ride Height Clarification #26600wordingwordingGT1 and GT2/GT3/LITE ride height requirements removed from GCR sections 9.1.2.D.5.a.1 and 9.1.2.F.7.b. 2019-04-01 STU Request to Use Japanese Mazda 13b Intake Manifold #25790inductionfasterSTU Mazda 13B Bridge Port may use ELITE ROTARY SHOP FD V2.0 intake manifold instead of stock. 2019-04-01 STU Request Alternate Intake for Mazda MZR In a Rear Wheel Drive App. #26352inductionunclearSTU Mazda MZR LF/L3/L5 may use Goodwin Part #61-2510 intake manifold with stock or Acura throttle body. 2019-04-01 STU E&O Suspension #26424wordingwordingSTU suspension rules clarified: alternate components from same manufacturer moved from section E to section D. 2019-04-01 STU Revisit B20 VTEC #26530enginefasterSTU Honda/Acura B20 classified at 1973 cc, now permits VTEC B16 or B18 cylinder head and intake manifold. 2019-04-01 STU Move Flared Fenders to STU Advanced Aero #26564aeroaeroSTU flared fenders up to 2" with 1% weight penalty moved from base to Advanced Aero rules. 2019-04-01 STU TCA Civic SI E&O #26606tyres & wheelsslowerTCA Honda Civic Si (2017-) must run 37mm TIR maximum as of June 1, 2019. 2019-04-01 STU S54 Spec line #26620wordingwordingSTU BMW S54B32 OEM reclassified from E46 designation, 3246 cc, 3300 lbs minimum weight. 2019-03-01 P2 Change Engine Table Lines B.1 & B.5 #25777inductionslowerP2 stock engine restrictor shrinks to 35.0mm and weight rises to 1025 lbs; modified engine restrictor to 34.0mm, weight to 1125 lbs; line B.5 restrictor to 33.0mm, weight to 1185 lbs. 2019-03-01 P2 Change Line A.1 restrictor size #26429inductionslowerP2 Line A.1 restrictor reduced from 40mm to 38mm. 2019-03-01 STU Request to Class Assignment for 2017 Civic #24287cars addedcars addedHonda Civic Si 2017- classified STU at 1500cc, 2800 lbs minimum with OEM engine and bodywork. 2019-03-01 STU Request to run E46 3246cc in STU #25126cars addedcars addedSTU BMW E46 S54 OEM 3246cc added at 3300 lbs minimum weight, no Super Touring allowances. 2019-03-01 STU Engine Classification for Rotary #25564wordingunclearSTU Mazda 13B and 13B Bridge Port may use RE or REW housings and intake with turbo removed. 2019-03-01 STU K24/K20 Head Swap Clarification/Amendment #25899wordingwordingSTU Honda K24 may use intake part #s 17100-RRB-A00 or 17100-PRB-A10. 2019-03-01 STU Request to Classify 12a Bridge Ported Rotary Engine #25985cars addedcars addedSTU Mazda 12A Bridge Port engine classified at 2550 lbs minimum weight with specified carburetor induction options. 2019-03-01 STU World Challenge Car Eligibility #26387wordingunclearSTU World Challenge car weight calculation method removed; new basis unclear from text provided. 2019-03-01 STU Request a phone call for discussion regarding weight #26398inductionfasterSTU AWD cars no longer required to reduce restrictor 1 mm from table. 2019-03-01 STU Advanced Aero E&O #26413aeroaeroSTU rear wing maximum cord length set to 12 inches, end plates to 72.0 square inches each. 2019-01-01 GT1 GTX Homologation table update #26034cars addedcars addedGTX FIA GT3: Audi R8 40mm restrictor 2900 lbs, BMW Z4 70mm 2800 lbs, Ferrari 488 35mm restrictor 3025 lbs classified. 2019-01-01 P2 Request to Allow 1345cc Hayabusa Engines for Spec Line P2 Cars #25595enginefasterP2 Spec Line cars now allow 1345cc Hayabusa stock engines at 1050 lbs with 30mm restrictor. 2019-01-01 P2 Change CN inlet restrictor implementation date #25816wordingwordingP2 Group CN Honda K20A-FD2 55mm restrictor implementation delayed from 1/1/2019 to 3/1/2019. 2019-01-01 P2 Clarify Honda K20A-FD2 parts requirement #25950inductionslowerP2 Honda K20A-FD2 in CN chassis must use stock intake manifold with 64mm throttle body and 55mm restrictor at 1500 lbs minimum weight. 2019-01-01 STU Request to Equalize Direct Injected Turbo Cars #24890cars addedcars addedSTU Honda K20C1 Turbo I4 1996cc added at 3025 lbs minimum weight with 36mm TIR.

Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.