BoP Lab / Laguna Seca

AS vs STL vs STU vs FF pace at Laguna Seca

Quickest here: AS 1:40.712 Clark Nunes, Hoosier SCCA Super Tour (San Francisco Region) qualifying · STL 1:42.330 Tim Auger, Hoosier SCCA Super Tour (San Francisco Region) race · STU 1:39.256 David Fiorelli, Hoosier SCCA Super Tour (San Francisco Region) qualifying · FF 1:34.290 Chuck Horn, Hoosier SCCA Super Tour (San Francisco Region) qualifying

	Event	AS			STL					STU					FF
	Event	Qual best	Race best	Trap	Qual best	Race best	Trap	vs AS	% of AS	Qual best	Race best	Trap	vs AS	% of AS	Qual best	Race best	Trap	vs AS	% of AS
	Hoosier SCCA Super Tour (San Francisco Region) ST19JUL262019-07-26	1:40.712Clark Nunes · fastest of 4 · top 4 within 7.9s	1:40.914Clark Nunes · fastest of 4 · top 4 within 8.0s	103.0Michael Thompson	1:42.773Tim Auger · fastest of 7 · top 5 within 4.9s	1:42.330Tim Auger · fastest of 6 · top 5 within 4.5s	95.7Thomas Lepper	+1.416squal +2.061s	101.4%qual 102.0%	1:39.256David Fiorelli · fastest of 3 · top 3 within 3.9s	1:41.478Nathan Pope · fastest of 3 · top 3 within 2.9s	104.9David Fiorelli	+0.564squal -1.456s	100.6%qual 98.6%	1:34.290Chuck Horn · fastest of 7 · top 5 within 1.8s	1:35.120Courtney Crone · fastest of 7 · top 5 within 1.6s	104.0Chuck Horn	-5.794squal -6.422s	94.3%qual 93.6%
36 earlier rule changes on record, in force before Hoosier SCCA Super Tour (San Francisco Region) (from 2019)7 cars added · 7 induction · 3 engine · 2 aero · 2 weight · 1 tyres & wheels · 14 wording · STU alternate intake manifolds now allowed case-by-case instead of prohibited. · STU Nissan SR20DET removes -2mm penalty in Table B. · STU alternate intake manifolds now allowed case-by-case instead of prohibited. · AS Ford Mustang (79-93) 313 CID and under loses 100 lbs to 3150; over 313 CID loses 100 lbs to 3450. · STL Acura/Honda B18 except C engine restrictor increases from 53mm to 54mm flat plate. · STU aftermarket side skirts must meet 3-inch ride height, no openings except jacks or side exhaust, no wider than fascias, not higher than door bottom, no chassis reinforcement. · STU fender flare wording clarified: each fender may be flared up to 2" for tire clearance with 1% weight penalty. · STL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. · STL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. · STU Mazda 13B Bridge Port may use ELITE ROTARY SHOP FD V2.0 intake manifold instead of stock. · STU Mazda MZR LF/L3/L5 may use Goodwin Part #61-2510 intake manifold with stock or Acura throttle body. · STU suspension rules clarified: alternate components from same manufacturer moved from section E to section D. · STU Honda/Acura B20 classified at 1973 cc, now permits VTEC B16 or B18 cylinder head and intake manifold. · STU flared fenders up to 2" with 1% weight penalty moved from base to Advanced Aero rules. · TCA Honda Civic Si (2017-) must run 37mm TIR maximum as of June 1, 2019. · STU BMW S54B32 OEM reclassified from E46 designation, 3246 cc, 3300 lbs minimum weight. · STL adds VW 1.8L R4 20VT 1781cc, 1 minimum weight, turbo removed permitted. · STL Mazda Renesis minimum weight reduced from 2800 to 2700 lbs. · STL Mazda MX-5 Cup brake pad compound changed to open. · STL adds Acura/Honda B18C1 GSR with 54mm flat plate restrictor and port matching limited to 1 inch. · STL Mazda 12 and 13B now permit port matching; previous ban removed. · Honda Civic Si 2017- classified STU at 1500cc, 2800 lbs minimum with OEM engine and bodywork. · STU BMW E46 S54 OEM 3246cc added at 3300 lbs minimum weight, no Super Touring allowances. · STU Mazda 13B and 13B Bridge Port may use RE or REW housings and intake with turbo removed. · STU Honda K24 may use intake part #s 17100-RRB-A00 or 17100-PRB-A10. · STU Mazda 12A Bridge Port engine classified at 2550 lbs minimum weight with specified carburetor induction options. · STU World Challenge car weight calculation method removed; new basis unclear from text provided. · STU AWD cars no longer required to reduce restrictor 1 mm from table. · STU rear wing maximum cord length set to 12 inches, end plates to 72.0 square inches each. · AS Spec Mustang (SMG) newly classified with 107.1 wheelbase, 3.73 gears, 355mm front brakes, 300mm rear. · FF Honda Fit permitted to use 0.25mm oversize pistons, cylinder honing increased to 73.315mm maximum. · FF heat shield rule clarified: thermal wrap allowed on manifold exterior if easily removable for inspection. · FF catch tank minimum capacity rules clarified: coolant catch tank now one U.S. pint minimum, oil catch tank one U.S. quart minimum. · STL B18C Type R variants get 54mm flat plate restrictor; B17 also gets 54mm restrictor. · STL Mazda Miata removes maximum displacement limit and adjusts minimum weight. · STU Honda K20C1 Turbo I4 1996cc added at 3025 lbs minimum weight with 36mm TIR.showhide 2019-07-01 STL Request clarification for manifold and throttle in STU #27004inductionfaster · inductionSTU alternate intake manifolds now allowed case-by-case instead of prohibited. 2019-07-01 STU Remove -2mm penalty from SR20DET Nissan #26982enginefaster · engineSTU Nissan SR20DET removes -2mm penalty in Table B. 2019-07-01 STU Request clarification for manifold and throttle in STU #27004inductionfaster · inductionSTU alternate intake manifolds now allowed case-by-case instead of prohibited. 2019-05-31 AS Request to Revert to 2017 Weights #25885weightfaster · weightAS Ford Mustang (79-93) 313 CID and under loses 100 lbs to 3150; over 313 CID loses 100 lbs to 3450. 2019-05-31 STL Request Restrictor Plate correction #26779inductionfaster · inductionSTL Acura/Honda B18 except C engine restrictor increases from 53mm to 54mm flat plate. 2019-05-31 STU Request to clarify afterrmarket side skirts exhaust exit #26814wordingwordingSTU aftermarket side skirts must meet 3-inch ride height, no openings except jacks or side exhaust, no wider than fascias, not higher than door bottom, no chassis reinforcement. 2019-05-31 STU Wheel Flare wording #26872wordingwordingSTU fender flare wording clarified: each fender may be flared up to 2" for tire clearance with 1% weight penalty. 2019-05-01 STL Request Ride Height Clarification #26597wordingwordingSTL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. 2019-05-01 STU Request Ride Height Clarification #26597wordingwordingSTL and STU ride height measurement clarified: without driver, at rocker panel lowest point, excluding pinch weld. 2019-04-01 STU Request to Use Japanese Mazda 13b Intake Manifold #25790inductionfaster · inductionSTU Mazda 13B Bridge Port may use ELITE ROTARY SHOP FD V2.0 intake manifold instead of stock. 2019-04-01 STU Request Alternate Intake for Mazda MZR In a Rear Wheel Drive App. #26352inductionunclearSTU Mazda MZR LF/L3/L5 may use Goodwin Part #61-2510 intake manifold with stock or Acura throttle body. 2019-04-01 STU E&O Suspension #26424wordingwordingSTU suspension rules clarified: alternate components from same manufacturer moved from section E to section D. 2019-04-01 STU Revisit B20 VTEC #26530enginefaster · engineSTU Honda/Acura B20 classified at 1973 cc, now permits VTEC B16 or B18 cylinder head and intake manifold. 2019-04-01 STU Move Flared Fenders to STU Advanced Aero #26564aeroaeroSTU flared fenders up to 2" with 1% weight penalty moved from base to Advanced Aero rules. 2019-04-01 STU TCA Civic SI E&O #26606tyres & wheelsslower · tyres & wheelsTCA Honda Civic Si (2017-) must run 37mm TIR maximum as of June 1, 2019. 2019-04-01 STU S54 Spec line #26620wordingwordingSTU BMW S54B32 OEM reclassified from E46 designation, 3246 cc, 3300 lbs minimum weight. 2019-03-01 STL Request to Allow VW 1.8L Engine #25614cars addedcars addedSTL adds VW 1.8L R4 20VT 1781cc, 1 minimum weight, turbo removed permitted. 2019-03-01 STL Request to reduce weight of RX8 with Renesis rotary #25781weight -100 lbsfaster · weightSTL Mazda Renesis minimum weight reduced from 2800 to 2700 lbs. 2019-03-01 STL Request for Open Brake Pads On Mazda MX-5 Cup NC #25821wordingwordingSTL Mazda MX-5 Cup brake pad compound changed to open. 2019-03-01 STL Request to clarify B18C1 GSR Honda B motor table #26209cars addedcars addedSTL adds Acura/Honda B18C1 GSR with 54mm flat plate restrictor and port matching limited to 1 inch. 2019-03-01 STL Port Matching #26415wordingfasterSTL Mazda 12 and 13B now permit port matching; previous ban removed. 2019-03-01 STU Request to Class Assignment for 2017 Civic #24287cars addedcars addedHonda Civic Si 2017- classified STU at 1500cc, 2800 lbs minimum with OEM engine and bodywork. 2019-03-01 STU Request to run E46 3246cc in STU #25126cars addedcars addedSTU BMW E46 S54 OEM 3246cc added at 3300 lbs minimum weight, no Super Touring allowances. 2019-03-01 STU Engine Classification for Rotary #25564wordingunclearSTU Mazda 13B and 13B Bridge Port may use RE or REW housings and intake with turbo removed. 2019-03-01 STU K24/K20 Head Swap Clarification/Amendment #25899wordingwordingSTU Honda K24 may use intake part #s 17100-RRB-A00 or 17100-PRB-A10. 2019-03-01 STU Request to Classify 12a Bridge Ported Rotary Engine #25985cars addedcars addedSTU Mazda 12A Bridge Port engine classified at 2550 lbs minimum weight with specified carburetor induction options. 2019-03-01 STU World Challenge Car Eligibility #26387wordingunclearSTU World Challenge car weight calculation method removed; new basis unclear from text provided. 2019-03-01 STU Request a phone call for discussion regarding weight #26398inductionfaster · inductionSTU AWD cars no longer required to reduce restrictor 1 mm from table. 2019-03-01 STU Advanced Aero E&O #26413aeroaeroSTU rear wing maximum cord length set to 12 inches, end plates to 72.0 square inches each. 2019-02-01 AS SMG Mustang eligibility in American sedan #26224cars addedcars addedAS Spec Mustang (SMG) newly classified with 107.1 wheelbase, 3.73 gears, 355mm front brakes, 300mm rear. 2019-02-01 FF Request for Oversize Honda Fit Pistons #25810enginefaster · engineFF Honda Fit permitted to use 0.25mm oversize pistons, cylinder honing increased to 73.315mm maximum. 2019-02-01 FF Heat Shield - Fit Intake #26102wordingwordingFF heat shield rule clarified: thermal wrap allowed on manifold exterior if easily removable for inspection. 2019-02-01 FF Request catch cans/tanks clarification #26158wordingwordingFF catch tank minimum capacity rules clarified: coolant catch tank now one U.S. pint minimum, oil catch tank one U.S. quart minimum. 2019-01-01 STL Request to equalize FPR Reduction on all B-Series Vtec Engines #24746inductionslower · inductionSTL B18C Type R variants get 54mm flat plate restrictor; B17 also gets 54mm restrictor. 2019-01-01 STL Request E&O for Mazda Miata Spec Line #25955wordingunclearSTL Mazda Miata removes maximum displacement limit and adjusts minimum weight. 2019-01-01 STU Request to Equalize Direct Injected Turbo Cars #24890cars addedcars addedSTU Honda K20C1 Turbo I4 1996cc added at 3025 lbs minimum weight with 36mm TIR.

Best is the class's fastest lap in that event's qualifying or race sessions, with the driver who set it, how many cars set a time that session and how close the top five were; a best from fewer than three cars is greyed. With two or more classes, "vs" is the gap of each class's best to the first class's at the same event. "% of AS" is the class's best as a share of AS's best at the same event (100% is level, less is quicker): weather and track condition move every class together, so this compares across years where the raw times do not. It still breaks when AS's own field changes or one session was wet and another dry. Newest event first. The coloured figure under each value is the change from the previous event that has one (green is quicker, red slower). Whole laps only, so events with different sector layouts still compare. Weather and track condition are not accounted for.