FE2 + SRF + FC at Michelin Raceway Road Atlanta

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Front – Hoosier P/N 46100 1 P185/65R13 W2"

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5" with driver as raced when P185/60R13 (H20 or W2) tires are used."

RM 23-07, USF2000 Van Diemen with Mazda MZR LF-DE 2.0L in FC, GCR section 9.1.1.B.1, add a new section and re-letter the
following sections accordingly:
"c. The USF2000 tube frame Van Diemen car powered by the Mazda MZR LF-DE 2 liter engine is added as a "spec line" car in
Formula Continental. Additional "spec line" cars are disfavored, and Balance of Performance (BoP) adjustments to keep "spec
line" cars competitive with cars that meet the class formula are likewise disfavored."
In FC, GCR section 9.1.1.B.11, add the following:
"The only permitted engines are:
a. The Ford 2 liter single overhead camshaft "NE" series engine or the 1971-74 Pinto/Capri 2 liter single overhead camshaft
engine. The specifications are contained in B.15.
b. The Ford Zetec ZX3 2 liter dual overhead camshaft engine. The specifications are contained in B.16.
c. The Mazda MZR LF-DE 2 liter for use only in USF2000 cars, as described in the Spec Line Cars Table below."
In FC, GCR section 9.1.1.B, add the following:
In FX, GCR section 9.1.1.J.B, change as follows and renumber the remaining lines accordingly:
"3. USF2000 (tube frame) – Shall comply with FRP F2000 Technical Specifications (2018)
4. Pro Formula F2000 (tube frame) – Engine must be prepared to current FC rules."
In FX Table 1, remove the USF2000 Tube Frame and Pro Formula F2000 Tube Frame spec lines in their entirety.
Spec Line Cars Table

A specification table follows in the original; it is not shown here.

In FC, GCR section 9.1.1.B.10.h, change as follows:
"FC shall be is permitted a maximum of four (4) dry tires and four (4) wet tires for all Regional, Major, and Super Tour events;
eight (8) dry tires and eight (8) wet tires are permitted for the Runoffs. This rule shall be is effective beginning with the first (1st)
qualifying session of the event. Marked tires are not required for testing or practice. It is the competitor's responsibility to
ensure that the tires are declared, marked, and logged by Tech in advance of the tire(s) being used in a qualifying session or
race. Failure to participate on marked tires will result in a penalty.
1. Use of an undeclared tire shall automatically result in all times being disallowed in that session or finishing position in that
race.
2. If a tire is damaged during a qualifying session or a race, the competitor may replace the damaged tire with a used tire upon
approval by the Chief Steward without loss of time or finishing position. Second or subsequent damaged tires may similarly be
replaced upon approval by the Chief Steward, however but such shall will result in the loss of grid position in the subsequent race
or session; the competitor shall will start at the back of the grid. Replacement of a damaged tire with a new tire upon approval by
the Chief Steward will result in loss of grid position in the subsequent race or session."

In SRF, GCR section 9.1.8.D.1.V.j, change as follows:
"Radiator - Enterprises new style P/N 480465 (requires baffle P/N 480464) or P/N 480466 can be used. P/N 480466, may can be
replaced with Automotive P/N 1R698, CU698 or equivalent OEM manufacturer justified by one cross-reference chart equivalent,
as long as the size, shape, and material are the same as the original P/N. The capacity, core thickness, etc., cannot be changed
even if allowed under the above. The competitor is responsible for providing this documentation of the cross-reference P/N."

In SRF, GCR section 9.1.8.D.1.W.l, change as follows:
"A Super Bright LEDs Inc. rain / brake light comprised of a single standard trailer oval lamp, 2-1/4 inches x 6-1/2 inches, with
incandescent or LED illumination, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes
GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the
wiring harness. The secondary filament of the brake light assembly shall must be connected to a switch enabling its use as a rain
light."

In SRF, GCR section 9.1.8.D.1.W.l, change as follows:
"A Super Bright LEDs Inc. P/N PT-STRB-R24 (SCCA Enterprises P/N 180427A) rain / brake light, P/N PT-STRB-R24, is required in the
original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No
changes may be made to the original 3-pin connector on the wiring harness. An SCCA Enterprises P/N 1190503 Strobing Brake
Light Pigtail is required. The secondary filament of the brake light assembly must be connected to a switch enabling its use as
a strobing rain light. A Strobing Brake Light Kit P/N 1168003 is available, which includes the brake light and pigtail."

In SRF, GCR section 9.1.8.D.1.H, add the following:
"NO MODIFICATIONS ALLOWED. Front brake ducts are required, attached to the openings in the lower radiator baffles, any
flexible 4" duct material allowed, installed length minimum 12" maximum 36" in length. Must be securely fastened, Bracket Part
# P/N 800368 can be used. Shall Must serve no other purpose. An extension may be welded to the side of the throttle pedal to
improve heel-and-toe braking. Master cylinder casting / location must be used as delivered on P/N 180110 Pedal Mounting
support. Aeroquip style -3 braided stainless flex lines only, must attach to all brake components without modification. Brake pad
"anti-rattle" clips must be removed."
In SRF, GCR section 9.1.8.D.1.V, add the following:
"ii. Rear SADEV shift cable aluminum two-piece style clamp may be used. The P/N WM302007A clamp must serve no other
purpose."
In SRF, GCR section 9.1.8.D.1.X.k, add the following:
"Negative camber shall must not exceed 5.0 degrees absolute maximum front and rear."
In SRF, GCR section 9.1.8.D.1.AA.b, add the following:
"2. Height of the radiator opening vertical surface 3 1/2“ +/- 1/2"."
P2 Engine Table B.1
2008 and older Stock
Suzuki, Yamaha,
Honda, BMW
38.5mm
P2 Engine Table B.2 Not required
P2 Engine Table B.3 38.5mm
Modified
Engine
950 lbs.
1005cc max
P2 Engine Table B.1
2008 and older 37mm
P2 Engine Table B.2 Not required
P2 Engine Table B.3 39mm
Stock Engine
1050 lbs.

In FC Table FC Charts, add the following:
In FC, GCR section 9.1.1.B.1.c, change as follows:
"The USF2000 tube frame Van Diemen car powered by the Mazda MZR LF-DE 2 liter engine and the F2000 Metrik ZF2 car
equipped with 4-piston calipers is are added as a "spec line" cars in Formula Continental. Additional "spec line" cars are
disfavored, and Balance of Performance (BoP) adjustments to keep "spec line" cars competitive with cars that meet the class
formula are likewise disfavored."
FC Charts
Car Engine Wheel Width
(in) ± .060 Aero Transmission Weight Notes

A specification table follows in the original; it is not shown here.

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used.
OR
Front – Hoosier P/N 46101 P185/65R13 W2
Rear – Hoosier P/N 46105 P205/60R13 W2
1. It is forbidden to regroove tires.
2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for
violation will be the loss of qualifying times and/or the disqualification of race results.
3. Hoosier SRF/SRF3 Decal Placement:
Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to
the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the
rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including
SCCA Enterprises."

In FE, GCR section 9.1.1.I.2.U.b.3, change as follows:
"Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure."
In SRF, GCR section 9.1.8.D.1.U.b.3, change as follows:
"Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure. Item 1 will be done by
the CSR or other shop that is equipped for this type of work and will be paid directly."

In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows:
"Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose
to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the
rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including
SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1)
decal must be located on each side of the car and one (1) decal must be visible on the front."

In SRF, GCR section 9.1.8.D.2.H.23, change as follows:
"Air Filter: P/N WM301020 or K&N RC-9160"

In SRF, GCR section 9.1.8.D.1.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with
no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."

In SRF, GCR section 9.1.8.D.2.B, change as follows:
"Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the
nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."

In FC, GCR section 9.1.1.B.10.h, change as follows:
"(Effective 11/1/2024) FC is permitted a maximum of four (4) dry tires and four (4) wet tires for all Regional, Major, and Super
Tour events; eight (8) dry tires and eight (8) wet tires are permitted for the Runoffs. This is effective beginning with the first (1st)
qualifying session of the event. Marked tires are not required for The tire limit does not apply to testing or practice. It is the
competitor's responsibility to ensure that the tires are declared, marked, and logged by Tech immediately upon conclusion of the
first qualifying session, as provided in the event supplemental regulations, or per the instructions of the Race Director or Chief
Steward. in advance of the tire(s) being used in a qualifying session or race. Failure to participate on marked Use of tires in
excess of the number allowed will result in a penalty. Failure to participate on declared/marked/logged tires after the time
prescribed for the same may result in a penalty. If a tire is damaged during a qualifying session or a race, the competitor may
replace the damaged tire with a used tire upon approval by the Race Director or Chief Steward without loss of time or finishing
position. Second or subsequent damaged tires may similarly be replaced upon approval by the Race Director or Chief Steward,
but such will result in the loss of grid position in the subsequent race or session; the competitor will start at the back of the grid.
Replacement of a damaged tire with a new tire upon approval by the Race Director or Chief Steward will result in loss of grid
position in the subsequent race or session; the competitor will start at the back of the grid."

In FF, GCR section 9.1.1.B.20.A.3, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
In FC, GCR section 9.1.1.B.20.B.4, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."

In FE2, GCR section 9.1.1.G.2.E, add the following:
"g. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

In SRF, GCR section 9.1.8.D.1.D, add the following:
"f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

In SRF, GCR section 9.1.8.D.2.K, change as follows:
"OR
SADEV-SRF3 6-Speed Sequential (beginning from Oct. 4, 2021 onward):
1st 12-36 3.0000 : 1
2nd 15-31 2.0667 : 1
3rd 18-28 1.5556 : 1
4th 22-28 1.2727 : 1
5th 24-26 1.0833 : 1
6th 25-23 0.9200 : 1
Final Drive Ratio: 15-48 3.20"

In FE, GCR section 9.1.1.G.2.F.k, change as follows:
"Enterprises bubble tail P/N: WM138014 is allowed for FE and is the only configuration for FE2."

In SRF, GCR section 9.1.8.D.1.V.ff, change as follows:
"SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan
permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."

In FC Charts table, USF2000 Tube Frame spec line, add the following to the Notes:
"Cars originally built with the Hewland LD200 4-speed H-pattern may use that transmission as an alternative to the Hewland JL-
200 5-speed sequential transmission."

In FC Charts table, F2000 Metrik ZF2 spec line, change the Weight as follows:
"1240 1220"

In SRF, GCR section 9.1.8.D.2.H.18, add the following:
"Spark Plugs: P/N G301041 ONLY NGK LTR7IX-11 / Washers or sealing rings are not allowed for any purpose."