FE2 + AS + SRF + FV at Michelin Raceway Road Atlanta

In AS, GCR Section 9.1.6.F.2., change as follows:
"GM Performance parts CT400 P/N-1937 → 0604 or 1937 → 0604 engine assembly for GM produced vehicles."

In AS Spec Lines, Ford Mustang GT 5.0l (15-17) Restricted Preparation, change Notes as follows:
"Max. Wheel Size: Dia.18.0 19.0 inches."

In AS SPEC Lines, Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2
valves/cylinder, change Notes as follows:
"SPC-66045 Alternate front upper control arms are permitted."

In AS SPEC Lines, Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2
valves/cylinder, change Notes as follows:
"Stock brakes or alternate Dodge brakes (Part numbers: front caliper (0517 → 5106 (R) and 0517 → 5107 (L); rear caliper (R1542564 (R)
and R1542565 (L))) may be used with the brake rotor sizes listed in this specification line. Alternate brackets may be used to
facilitate updated/backdated components."

In FV, GCR section 9.1.1.C.10.G, change as follows:
"Front W wheel bearings"

In AS Spec Lines, classify Chevrolet Camaro, Pontiac Firebird (70-81) Full Prep as follows:
AS Wheelbase Gear Ratios
Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs) Notes:

A specification table follows in the original; it is not shown here.

In AS Spec Lines, add to Notes as follows:
Cadillac CTS-V (04-07): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken
from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.”
Chevrolet/Pontiac Camaro & Firebird (93-02): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell.”
Chevrolet/Pontiac Camaro & Firebird (93-02): “Fuel cells must be located within 24 inches of the standard tank. The 24
inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell.”
Chevrolet Camaro SS (V8) (10-15): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell.”
Chevrolet Camaro (10-15): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is
taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”
Dodge Challenger (08-20): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is
taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”
Ford Mustang GT (05-14): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is
taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”
Ford Mustang Coupe GT (05-14): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell.”
Ford Mustang GT 5.0l (15-17): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement
is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”
Ford Mustang GT (05-14): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is
taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”

In AS Spec Lines, classify Chevrolet Camaro (16-) Full Prep as follows:
AS
Wheelbase Gear Ratios
Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs) Notes:
Chevrolet
Camaro (16-)
Full Prep
110.6 3.42, 2.28,

A specification table follows in the original; it is not shown here.

In AS Spec Lines, classify Ford Mustang GT (05-14) with Restricted prep Engine as follows:
AS
Wheelbase Gear Ratios Std.

A specification table follows in the original; it is not shown here.

In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (93-02), add to Notes the following:
"For the LS1connecting rods Callies p/n CSC6100DS6A2AH, Scat rods p/n 2-1CR6100-944, GM performance rods p/n 12649190."
In AS Spec Lines, Pontiac GTO (04-06), add to Notes the following:
"For the LS1connecting rods Callies p/n CSC6100DS6A2AH, Scat rods p/n 2-1CR6100-944, GM performance rods p/n 12649190."

In AS Spec Lines, Cadillac CTS-V (04-07), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Chevrolet Camaro SS (V8) (10-15), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Dodge Challenger (08-20), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Ford Mustang GT 5.0l (15-17), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Pontiac GTO (04-06), add to Notes the following:
"11" wide wheels can be used until 3/1/25."

In AS Spec Lines, classify Chevrolet Camaro 1LE (2016-) as follows:
AS Wheelbase Gear Ratios Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs.) Notes:
Chevrolet
Camaro, 1LE
(2016-)
110.6 2.66,1.78,1.30,0.74,.5 (F)

A specification table follows in the original; it is not shown here.

In AS Spec Lines, classify Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V-8 LS1 (Aluminum Block, Aluminum Heads) 2 valves
per cylinder, as follows:
AS Wheelbase Gear Ratios Std.

A specification table follows in the original; it is not shown here.

In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (82-92), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (93-02), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Chevrolet Camaro (10-15), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86), add to Notes the following:
"Flo Tek Part # 203-500 are permitted."
In AS Spec Lines, Ford Mustang Including Cobra 94-04, add to Notes the following:
"Flo Tek Part # 203-500 are permitted."
In AS Spec Lines, Ford Mustang GT (05-14), add to Notes the following:
"Flo Tek Part # 203-500 are permitted."

AS Spec Lines, classify Ford Mustang GT 5.0L (2018-) as follows:
AS Wheelbase Gear Ratios

A specification table follows in the original; it is not shown here.

In FE, GCR section 9.1.1.I.2.U.b.3, change as follows:
"Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure."
In SRF, GCR section 9.1.8.D.1.U.b.3, change as follows:
"Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure. Item 1 will be done by
the CSR or other shop that is equipped for this type of work and will be paid directly."

In AS Spec Lines, Ford Mustang GT (05-14) with Restricted Prep Engine, add to Notes as follows:
"Alternate transmission Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68.”
In AS Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows:
"Alternate transmission Ratios 3.24, 2.10, 1.42, 1.00, 0.81, .062."

In FV, GCR section 9.1.1.C.4.D, change as follows:
"Any ferrous alloy, unvented rotor may be used, but must have a maximum diameter of 11.75 in. and a minimum thickness of
0.20 in. The otherwise smooth rotor may not be cross-drilled and may have a maximum of three pad cleaning grooves per side."

In AS Spec Lines, add to Notes as follows:
Ford mustang (GT 05-14): "Gen 1- 67mm Gen 2-64mm"
Ford mustang (GT 05-14): "Gen 1- 67mm"
Ford mustang (GT 15-17): "Gen 1- 67mm"
Ford mustang (GT 94-04): "Gen 1- 67mm Gen 2-64mm"
Ford mustang cobra & Cobra R Mercury Capri (79-93) (79-86): "Gen 1- 67mm Gen 2-64mm"

In AS Spec Lines, Ford Mustang Coupe GT (05-14) Restricted Prep., change Notes as follows:
"The 4.6L engine assembly has a weight reduction of 300 lbs. 5.0L/6spd engine/trans: track pack front and rear spoiler allowed."
In AS Spec Lines, Ford Mustang Coupe GT (05-14) with Restricted Prep. engine, change Notes as follows:
"Max. Wheel Size: Dia.18.0 inches. Stock brakes or alternate Ford 14” Brembo Brake (Ford Racing Kit #M-2300-S) and full prep
brake package may be used. Either engine may be used. 1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l
Coyote 15-17 61mm FPR Cold Air Intake allowed Charge Motion Control Valves can be blocked off and removed for firewall
clearance Allow Cold Air Intake Tremec Magnum transmission may be used P/N- TUKT16901. Full Prep Transmissions rule
package may also be used. Max compression ratio, 11.2:1 track pack front and rear spoiler allowed. Alternate transmission
Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68."
In AS Spec Lines, Ford Mustang GT 5.0l (15-17) Restricted Preparation, change Notes as follows:
"Max. Wheel Size: Dia. 18.0 inches. Stock brakes or alternate Ford Brembo Brake caliper (Ford Racing Kit #M-2300-S) may be
used. 61mm flat plate restrictor required. Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation
of a safety fuel cell. 11” wide wheels can be used until 3/1/25. Performance pack front and rear spoiler, body kit allowed."
In AS Spec Lines, Ford Mustang GT 5.0L (2018-), change Notes as follows:
"Package Brembo front BBK and 380mm rotors permitted (Ford PN M-2300-V) at no weight penalty. 60mm flat plate restrictor
required. 2014 Mustang GT exhaust manifolds permitted. Ford Racing oil pan #M-6675-M50BR permitted. Alternate
transmission Ratios 3.24, 2.10, 1.42, 1.00, 0.81, .062. Performance pack front and rear spoiler, body kit allowed."

In AS Spec Lines, change Gear Ratios as follows:
Cadillac CTS-V (04-07):
"2.97, 2.07, 1.43,1.00, 0.84,0.56 or 3.01, 2.07, 1.43, 1.0, .84, .57 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33, 1.00"
Chevrolet Camaro, Pontiac Firebird (70-81), Full Prep:
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61, or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00"
Chevrolet Camaro, Pontiac Firebird (70-81), Restricted Prep.:
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61, or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00"
Chevrolet/Pontiac Camaro & Firebird (82-92) Full Prep:
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33,
1.00"
Chevrolet/Pontiac Camaro & Firebird (93-02) Full Prep:
"3.42, 2.28, 1.45,1.00 or 2.95, 1.94,1.34, 1.00,0.73or 3.35, 1.93,1.29, 1.00,0. 61 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00,
0.68 or 2.20,1.64,1.28,1.00 or 2.87,1.89,1.28,1.00,.81"
Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted prep:
"2.97, 2.07, 1.43, 1.00, 0.80, 0.62 or 3.36, 2.07, 1.35, 1.00, .80, .62 or 2.66, 1.78, 1.30, 1.00, 0.74, 0.50 or 2.88, 1.91, 1.33, 1.00 or
2.20, 1.64,1.28,1.00"
Chevrolet Camaro SS (V8) (10-15) Restricted Prep:
"3.01, 2.07, 1.43, 1.0, .84, .57 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Chevrolet Camaro (10-15) Full Prep:
"3.42, 2.28, 1.45,1.00 or 2.95, 1.94,1.34, 1.00, 0.73or 3.35, 1.93,1.29, 1.00,0. 61 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00,
0.68 or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00,.81"
Chevrolet Camaro (16-) Full Prep:
"3.42, 2.28, 1.45,1.00 or 2.95, 1.94,1.34, 1.00, 0.73or 3.35, 1.93,1.29, 1.00,0. 61 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00,
0.68 or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00,.81"
Chevrolet Camaro, 1LE (16-):
"2.66,1.78,1.30, 0.74,.50 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2 valves/cylinder:
"2.97, 2.1, 1.46, 1.00, 0.74, 0.50 or 2.26, 1.58, 1.19, 1.00, 0.77, 0.63 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86) Full Prep:
"3.07, 1.72, 1.00, 0.70 or 2.95, 1.94, 1.34, 1.00, 0.63 or 3.35, 1.99, 1.33, 1.00, 0.68 or 2.87 1.89 1.28 1.00 0.81"
Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86) with Restricted Prep Engine:
"2.95, 1.94, 1.34,1.00, 0.63 or 3.35,1.99,1.33, 1.00, 0.69 or 2.88, 1.91, 1.33, 1.00 or 3.27,1.98, 1.34, 1.00, 0.68, 3.66, 2.43, 1.69,
1.32, 1.00, .68. or 2.87,1.89,1.28,1.00,.81"
Ford Mustang Including Cobra 94-04 Full Prep:
"3.07, 1.72, 1.00, 0.70 or 2.95, 1.94, 1.34, 1.00, 0.63 or 3.35, 1.99, 1.33, 1.00, 0.68 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34,
1.00, 0.68 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 or 2.20, 1.64,1.28,1.00 or 2.87 1.89 1.28 1.00 0.81"
Ford Mustang Cobra and GT 94-95 (Restricted Prep):
"3.35, 1.99, 1.33, 1.00, 0.68 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang including Cobra 96-04 (Restricted Prep) 4.6L two and four valve motor:
"3.35, 1.99, 1.33, 1.00, 0.68 or 3.27, 1.98, 1.34, 1.00, 0.67 or 3.37, 1.99, 1.33, 1.00, 0.68 or 3.38, 2.00, 1.32, 1.00, 0.68 or 2.88,
1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang GT (05-14) Full Prep:
"3.38, 2.00, 1.32, 1.00, 0.68 or 3.66, 2.43, 1.69,1.32, 1.00, 0.65 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang GT 5.0l (15-17) Restricted Preparation:
"3.66, 2.43, 1.69,1.32, 1.00, .65 or 4.69, 2.98,2.14, 1.76,1.52, 1.27,1.00, 0.85, 0.68, 0.63, or 3.24, 2.10, 1.42, 1.00, 0.81, .062. or
2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang GT 5.0L (2018-) Restricted Preparation:
"2.97, 2.07, 1.43, 1.00, 0.84, 0.57 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Pontiac GTO (04-06) Restricted Prep.
"2.97, 2.07, 1.43, 1.00, 0.84, 0.57 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"

In AS SPEC LINES, Cadillac CTS-V (04-07) Restricted Prep., change Notes as follows:
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Tremec TR6060
Transmission with 3.0 1, 2.07, 1.43, 1.0, .84, .57 ratios permitted. 11” wide wheels can be used until 3/1/25. Any ECM may be
used."
In AS SPEC LINES, Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep ., add to Notes as follows:
"Any ECM may be used."
In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V-8 LS1, add to Notes as follows:
"Any ECM may be used."
In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted Prep.5.7L V-8 LT1, add to Notes as follows:
"Any ECM may be used."
In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted Prep. 5.7L V-8 LT1; 98-02 , change Notes as follows:
"5.7L LS1:
GM Performance Parts camshaft Kit P/N-19355738 is permitted. Cylinder Bore, 99 mm; Stroke, 92 mm; Intake Valve Diameter,
50.8; Exhaust Valve Diameter, 39.4 mm; Throttle Body Bore, 75 mm; SLP Intake Lid (SLP part number 21044 (98-99) and 21045
(00-02)) is permitted.
Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.
1-3/4 headers allowed. For the LS1connecting rods Callies P/NCSC6100DS6A2AH, Scat rods P/N2-1CR6100-944, GM performance
rods P/N12649190. Any ECM may be used."
In AS SPEC LINES, Chevrolet Camaro SS (V8) (10-15) Restricted Prep., add to Notes as follows:
"Any ECM may be used."

In AS Spec Lines, change Notes as follows:
Cadillac CTS-V (04-07) Restricted Prep. 6.0L V8 (Aluminum block, Aluminum heads), LS2, 2 valves/cylinder:
"Any ECM maybe used."
Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep. 6.2L V8 (Aluminum Block, Aluminum Heads), 2 valves per cylinder:
"Any ECM maybe used."
Chevrolet/Pontiac Camaro & Firebird (82-92)s 5.7L V-8 LS1 (Aluminum Block, Aluminum Heads) 2 valves per cylinder:
"Any ECM maybe used."
Chevrolet/Pontiac Camaro & Firebird (93-02):
"Any ECM maybe used."
Chevrolet Camaro SS (V8) (10-15) Restricted Prep. 6.2L V8 (Aluminum Block, Aluminum Heads), 2 valves per cylinder:
"Any ECM maybe used."

In GCR, Section 9.1.6., replace Figure 1 Value Seat Cutting Dimensions with the following:

In AS Spec Lines, change/add to Notes as follows:
Cadillac CTS-V (04-07):
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used. The
Drive Shaft Shop, Axle shaft part #'s 510220/510221 permitted."
Chevrolet Camaro, Pontiac Firebird (70-81) Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #s: 14101081, 14014416 Port Volume (Max.): 081
casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb. weight reduction. Edelbrock Cylinder Head Part
#s 608979, 608879."
Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep.:
"Any ECM maybe used."
Chevrolet/Pontiac Camaro & Firebird (82-92) Full Prep.:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #s: 14101081, 14014416 Port Volume (Max.): 081
cast¬ing: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb weight reduction. Edelbrock Cylinder Head Part
#s 608979, 608879 are permitted. For regional competition only, unmodified GM Performance cylinder head part #s 19300955,
19300956 may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186 installed between intake
manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on each side of the restrictor.
All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98,
1.34, 1.00, 0.68 are permitted. Flo Tek Head part #102-500 are permitted."
Chevrolet/Pontiac Camaro & Firebird (82-92) Restricted prep engine:
"Any ECM maybe used."
Chevrolet/Pontiac Camaro & Firebird (93-02) Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #’s: 14101081, 14014416; Port Volume (Max.):
081 casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb weight reduction. Edelbrock Cylinder Head
Part #’s 608979, 608879 are permitted. For regional competition only, unmodified GM Performance cylinder head part #s
19300955, 19300956 may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186 installed
between intake manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on each side
of the restrictor. All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91, 1.33, 1.00
or 3.27, 1.98, 1.34, 1.00, 0.68 are permitted. Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell. Flo Tek Head part #102-500 are permitted."
Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted Prep:
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used."
Chevrolet Camaro SS (V8) (10-15) Restricted Prep:
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used."
Chevrolet Camaro (10-15) Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #’s: 14101081, 14014416; Port Volume (Max.):
081 casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 200 lb weight reduction. Edelbrock Cylinder Head
Part #’s 608979, 608879 are permitted. Alternate gear ratio sets 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 are
permitted. Fuel cells must be located within 24 inches of the standard tank. The 24-inch measurement is taken from the
perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Flo Tek
Head part #102-500 are permitted. Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is
taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel
cell."
Chevrolet Camaro (16-) Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #’s: 14101081, 14014416; Port Volume (Max.):
081 casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 200 lb weight reduction. Edelbrock Cylinder Head
Part #’s 608979, 608879 are permitted, Flo Tek Head part #102-500 are permitted."
Chevrolet Camaro, 1LE (16-):
"60mm flat plate restrictor required. Any ECM maybe used."
Dodge Challenger (08-20) Restricted Preparation:
"80mm flat plate restrictor is required on the 6.4L engine. Fuel cells must be located within 24 inches of the standard tank. The
24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell."
Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86) Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #s: F3ZE AA (GT40), F1ZE-AA (GT-40), F77E-AA
(GT- 40P), Port Volume (Max.): 143.00cc IN/54.00cc EX (GT-40 & GT-40P) with a 250 lb weight reduction. Edelbrock Cylinder
Head Part #s 602579, 602479 are permitted. For regional competition only, unmodified Ford Performance cylinder head part #s
M-6049-Z304DA7, M-6049-Z304D may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186
installed between intake manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on
each side of the restrictor. All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91,
1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 are permitted. Flo Tek Part # 203-500 are permitted."
Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri(79-86) with Restricted Prep Engine:
"62mm flat plate restrictor is required. Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang Including Cobra 94-04 Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #s: F3ZE AA (GT40), F1ZE-AA (GT-40), F77E-AA
(GT- 40P), Port Volume (Max.): 143.00cc IN/54.00cc EX (GT-40 & GT-40P) with a 250 lb weight reduction. Edelbrock Cylinder
Head Part #s 602579, 602479 are permitted. For regional competition only, unmodified Ford Performance cylinder head part #s
M-6049-Z304DA7, M-6049-Z304D may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186
installed between intake manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on
each side of the restrictor. All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91,
1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 are permitted. Flo Tek Part # 203-500 are permitted."
Ford Mustang GT (94-04) with Restricted Prep Engine:
"MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang Cobra and GT 94-95(Restricted Prep):
"1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66,
2.43, 1.69, 1.32, 1.00, .68. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang including Cobra 96-04 (Restricted Prep):
"1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66,
2.43, 1.69, 1.32, 1.00, .68. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang Coupe GT (05-14) Restricted Prep.:
"1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66,
2.43, 1.69, 1.32, 1.00, .68. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted. MT82 6 speed is permitted."
Ford Mustang GT (05-14) with Restricted Prep Engine:
"1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66,
2.43, 1.69, 1.32, 1.00, .68. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted. MT82 6 speed is permitted."
Ford Mustang GT 5.0l (15-17) Restricted Preparation:
"61mm flat plate restrictor required. Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement
is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety
fuel cell. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang GT 5.0L (2018-):
"60mm flat plate restrictor required. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."

In FE2, GCR section 9.1.1.G.2.E, add the following:
"g. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

In AS Spec Lines, Ford Mustang GT 5.0l (15-17), Flat Plate Restrictor Size, change as follows:
"67mm 64mm"

In GCR, Section 9.1.6.F., add the following to Intake Part #’s:
"17113697, 19418185, 89017230, 89017363, 89017364, and 89017365, 12561269 and 88894095"

In AS Spec Lines, Ford Mustang GT (05-14) with Restricted Prep Engine, add to Gear Ratios the following:
"or 3.66, 2.43, 1.69, 1.32, 1.00, .65"

In AS Spec Lines, Ford Mustang GT 5.0 (2018-), change Weight as follows:
"3600 3525"

In FE, GCR section 9.1.1.G.2.F.k, change as follows:
"Enterprises bubble tail P/N: WM138014 is allowed for FE and is the only configuration for FE2."

In AS Spec Lines, Cadillac CTS-V (04-07) Restricted Prep., change Weight as follows:
"(Effective 11/1/2025) 3450 3400"

In AS Spec Lines, Ford Mustang GT(94-04) with Restricted Prep Engine, add to notes the following:
"Ford Motorsport #M-6250-F303 camshaft is permitted."

In AS Spec Lines, change Restrictor as follows:
Ford Mustang Incl. Cobra and Cobra R (79-93) and Mercury Capri (79-86) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang GT (94-04) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang Coupe GT (05-14) Restricted Prep 5.0L/6 speed 4 valves per cylinder: "64 mm 61 mm"
Ford Mustang GT (05-14) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang GT 5.0L (15-17) Restricted Preparation: "64 mm 61 mm"

In GCR, Section 9.1.6.D.2.h.2., add the following:
"(Effective 2/1/2026) i. Weight based on full preparation chassis choice spec line for GM LM7 5.3L
Carburetor Option:
Must use the full prep 4776 holly carburetor and spacer gasket
Edelbrock Performer RPM 71187 intake manifold
MSD 6014 ignition box
(Edelbrock part # kit 7118)"

This AS Spec Lines re-organization simplifies the Spec Lines for all drivers. This version gives the chassis information on what
engines can be put in their cars. It removes information that is now repeated in the ruleset and adds engine/weight combos as
well as wheelbase/tire size information. The Notes in the Spec Lines have been reviewed to remove information now listed in
the engine build sheets and retain information pertinent to the chassis selected. Where there is nothing in the notes, it is not an
error. It just means everything a driver needs is now in the main rules or the build sheets.
In AS Spec Lines, delete current Spec Line in its entirety as follows:

A specification table follows in the original; it is not shown here.