No map published for Cal Club 2024, Cal Club 2023.
This track has been raced on 4 configurations (The Circuit, 2.57 mi; 19, 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
FE has no laps in the events chosen. It ran at Super Tour Apr 2019, Super Tour Apr 2018, Super Tour Apr 2017: add those events.
SRF has no laps in the events chosen. It ran at Super Tour Apr 2017, Majors Apr 2016: add those events.
One session is left out because the timing does not look like full laps: Cal Club 2023 Qualifying #2.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Mazda Miata
STL
17
1:51.665Jared Korth
1:54.963Nick Leverone
1:54.845Gavin Wardle
136.6Bryce Johnson
8.264Gavin Wardle
32.218Jared Korth
48.811Jared Korth
Mazda MX-5
STL
6
1:51.665Jared Korth
1:57.404Ryan Gutile
1:54.845Gavin Wardle
136.6Bryce Johnson
8.264Gavin Wardle
32.218Jared Korth
48.811Jared Korth
Mazda Miata
STL
10
1:52.983Wesley Mollno
1:54.963Nick Leverone
1:55.682Nick Leverone
133.4Wesley Mollno
30.815Jon Davies
32.820Jon Davies
49.197Wesley Mollno
Mazda MX-5 (2015)
STL
1
2:00.239Adrian Comstock
2:00.239Adrian Comstock
2:00.722Adrian Comstock
133.0Adrian Comstock
32.847Adrian Comstock
34.493Adrian Comstock
52.675Adrian Comstock
Mazda RX-8
STL
1
1:53.515David LeCren
2:09.464David LeCren
2:11.372David LeCren
121.0David LeCren
31.217David LeCren
32.486David LeCren
49.550David LeCren
Honda Civic Si
STL
1
1:56.438Jonathan Lugod
1:57.331Jonathan Lugod
1:56.438Jonathan Lugod
106.8Jonathan Lugod
31.787Jonathan Lugod
33.468Jonathan Lugod
50.873Jonathan Lugod
Honda Prelude
STL
1
1:56.961Carl Young
1:57.917Carl Young
1:56.961Carl Young
104.5Carl Young
31.994Carl Young
33.745Carl Young
50.892Carl Young
Acura integra
STL
1
2:24.310Jack McEachern
2:24.310Jack McEachern
2:24.550Jack McEachern
77.6Jack McEachern
38.960Jack McEachern
41.141Jack McEachern
1:02.410Jack McEachern
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
In SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481"). The 1985 Renault Alliance solid front rotor (Reference: Bendix PRT1318 or Centrix 121.11004) may be used on front, rear, or both axles, but each axle must be paired to the same type rotor. The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038 may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind;
Show 4 more lines
maximum of one spring per caliper." P2 Engine Table Spec Line Engine Series
A specification table follows in the original; it is not shown here.
In STL Spec Lines, Table B: Alternate Vehicle and Engine Allowances, change Notes as follows: ITA-spec and ITS-spec RX7: "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires & Wheels. Tires must also conform to 9.1.4.2.Tires." ITS, ITA, ITB, or ITC vehicles (1985- ): "Must completely conform to ITCS specifications. Tires must conform to 9.1.4, Tires & Wheels. Tires must also conform to 9.1.4.2.Tires."
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5" with driver as raced when P185/60R13 (H20 or W2) tires are used."
In SRF, GCR section 9.1.8.D.1.V.j, change as follows: "Radiator - Enterprises new style P/N 480465 (requires baffle P/N 480464) or P/N 480466 can be used. P/N 480466, may can be replaced with Automotive P/N 1R698, CU698 or equivalent OEM manufacturer justified by one cross-reference chart equivalent, as long as the size, shape, and material are the same as the original P/N. The capacity, core thickness, etc., cannot be changed even if allowed under the above. The competitor is responsible for providing this documentation of the cross-reference P/N."
In SRF, GCR section 9.1.8.D.1.W.l, change as follows: "A Super Bright LEDs Inc. rain / brake light comprised of a single standard trailer oval lamp, 2-1/4 inches x 6-1/2 inches, with incandescent or LED illumination, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the wiring harness. The secondary filament of the brake light assembly shall must be connected to a switch enabling its use as a rain light."
wordingFE rain light now must meet FIA Standard 8874-2019, Technical List No. 76, effective 1/1/2024.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.N.f, change as follows: "Any rain light is allowed. Effective 1/1/2024, a rain light that meets FIA Standard 8874-2019, Technical List No. 76, is required as specified in GCR section 9.3.32.B.2."
In SRF, GCR section 9.1.8.D.1.W.l, change as follows: "A Super Bright LEDs Inc. P/N PT-STRB-R24 (SCCA Enterprises P/N 180427A) rain / brake light, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the wiring harness. An SCCA Enterprises P/N 1190503 Strobing Brake Light Pigtail is required. The secondary filament of the brake light assembly must be connected to a switch enabling its use as a strobing rain light. A Strobing Brake Light Kit P/N 1168003 is available, which includes the brake light and pigtail."
STL Alternate Carburetor Request for 79-85 RX7 12a
In STL Table B: Alternate Vehicle and Engine Allowances, Mazda RX-7 12A (79-85), change Notes as follows: "Street Porting of the engine only. Bridge porting, peripheral porting, and eyelash porting are prohibited. Contact SCCA National Office for details of Street porting. Stock Nikki 4 bbl carburetor on a stock manifold only. or auto-type 2 bbl w/42mm choke(s) on a “dual-y” manifold. Allow the standard removal of emissions related components, and allow air and fuel jets to be corrected. Modification of the water jacket in the area of the spark plug for cooling purposes is permitted."
In SRF, GCR section 9.1.8.D.1.H, add the following: "NO MODIFICATIONS ALLOWED. Front brake ducts are required, attached to the openings in the lower radiator baffles, any flexible 4" duct material allowed, installed length minimum 12" maximum 36" in length. Must be securely fastened, Bracket Part # P/N 800368 can be used. Shall Must serve no other purpose. An extension may be welded to the side of the throttle pedal to improve heel-and-toe braking. Master cylinder casting / location must be used as delivered on P/N 180110 Pedal Mounting support. Aeroquip style -3 braided stainless flex lines only, must attach to all brake components without modification. Brake pad "anti-rattle" clips must be removed." In SRF, GCR section 9.1.8.D.1.V, add the following:
Show 23 more lines
"ii. Rear SADEV shift cable aluminum two-piece style clamp may be used. The P/N WM302007A clamp must serve no other purpose." In SRF, GCR section 9.1.8.D.1.X.k, add the following: "Negative camber shall must not exceed 5.0 degrees absolute maximum front and rear." In SRF, GCR section 9.1.8.D.1.AA.b, add the following: "2. Height of the radiator opening vertical surface 3 1/2“ +/- 1/2"." P2 Engine Table B.1 2008 and older Stock Suzuki, Yamaha, Honda, BMW 38.5mm P2 Engine Table B.2 Not required P2 Engine Table B.3 38.5mm Modified Engine 950 lbs. 1005cc max P2 Engine Table B.1 2008 and older 37mm P2 Engine Table B.2 Not required P2 Engine Table B.3 39mm Stock Engine 1050 lbs.
wordingFE allows racer's tape for crash repair, panel security, and heat exchanger opening control; seam taping banned.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.P.c, add the following: "Racer's tape may be used to repair crash damage, or as a precautionary means of securing the body panels or retaining latches fasteners only. Crash-damage is defined as having occurred during the current event, and the tape should be of an appropriate color if possible. Taping of body seams is not allowed. Taping across heat exchanger openings as a way to control temperature is allowed and may serve no other purpose."
In GCR, Section 9.1.4.M.16., change as follows: "Power steering may be modified in any of the following ways: a. disconnected , pump, belt, pulley, and hoses may be removed. Hoses may also be looped. Steering rack or box may be modified internally to work without pump. b. an OEM manual steering rack for that model may be fitted c. an electric power steering pump may be fitted d. an OEM electric-assisted steering system may be used or any column mounted electric steering assist may be used e. an OEM hydraulic-assisted steering system may be used"
In GCR, 9.1.4.H.1., change as follows: "Minimum weights for cars with normally aspirated piston engines will be determined by 1.35 lbs/cc displacement for the installed engine (see the following table). Displacement is the factory displacement for the installed engine. For the purpose of weight assignment, engine displacement will be rounded to the nearest 50cc (e.g., 2176cc = 2200cc and 2175cc = 2150cc)." In GCR, 9.1.4.H.1., change Minimum Weight on Chart as follows: Factory Engine Displacement 1900: "Effective 3-1-24: 2565 2540" Factory Engine Displacement 1950: "Effective 3-1-24: 2633 2583"
Show 11 more lines
Factory Engine Displacement 2000: "Effective 3-1-24: 2700 2625" In GCR, 9.1.4.H.3., change as follows: "Front wheel drive cars with a strut type front suspension may reduce their minimum weight by 2.5 percent. Effective 3- 1-24: Front wheel drive cars with 95" or less wheelbase must add 1.25% to their minimum weight." In STL Spec Lines, change Notes as follows: Acura/Honda B16: "Effective 3-1-24: 53 51mm" Acura/Honda B17: "Effective 3-1-24: 53 51mm" Acura/Honda B18C1: "Effective 3-1-24: 53 51mm" Acura/Honda B18C (JDM Type R), B18C5 (USDM Type R), B18C6 (UK and Euro Type R), B18C7 (Australia Type R): "Effective 3-1-24:52 50mm" Mazda MZR: "Effective 3-1-24: 52 50mm"
addedFE requires five Hoosier decals: one small on nose or front shock cover, one 12" on each front wing plate, one 12" on each lower floor panel before rear wheels.As printed in Fastrack
In FE, GCR section 9.1.8.I.2.M, add the following: "b. Hoosier FE/FE2 Decal Placement: Five (5) "Hoosier" decals are required in the following locations: One (1) small "Hoosier" decal on the nose or the front shock cover of the car. One (1) 12" "Hoosier" decal on the outside vertical plane of each front wing plate. One (1) 12" "Hoosier" decal on the vertical plane of each of the lower floor panels just in front of the rear wheels. Hoosier decals are available, free of charge, from all Hoosier tire distributors and SCCA Enterprises."
SRF Update Rain Tire Rule and Hoosier Decal Placement
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used. OR Front – Hoosier P/N 46101 P185/65R13 W2 Rear – Hoosier P/N 46105 P205/60R13 W2
Show 8 more lines
1. It is forbidden to regroove tires. 2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for violation will be the loss of qualifying times and/or the disqualification of race results. 3. Hoosier SRF/SRF3 Decal Placement: Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises."
wordingFE and SRF protest fee rules redirected to GCR section 8.3.1.D for fees and procedure.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.U.b.3, change as follows: "Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure." In SRF, GCR section 9.1.8.D.1.U.b.3, change as follows: "Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure. Item 1 will be done by the CSR or other shop that is equipped for this type of work and will be paid directly."
wordingFE and SRF protest fee rules redirected to GCR section 8.3.1.D for fees and procedure.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.U.b.3, change as follows: "Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure." In SRF, GCR section 9.1.8.D.1.U.b.3, change as follows: "Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure. Item 1 will be done by the CSR or other shop that is equipped for this type of work and will be paid directly."
SRF Update to Letter 36619 with new Hoosier Contingency Decal Info
In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows: "Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the front."
FE Update on Letter 36620 with new Hoosier Contingency Decal Info
wordingFE Hoosier contingency decal requirement reduced from five decals in specific locations to three decals on sides and front.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.M.b, change as follows: "Five (5) "Hoosier" decals are required in the following locations: One (1) small "Hoosier" decal on the nose or the front shock cover of the car. One (1) 12" "Hoosier" decal on the outside vertical plane of each front wing plate. One (1) 12" "Hoosier" decal on the vertical plane of each of the lower floor panels just in front of the rear wheels. Hoosier decals are available, free of charge, from all Hoosier tire distributors and SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the front."
In SRF, GCR section 9.1.8.D.1.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."
In SRF, GCR section 9.1.8.D.2.B, change as follows: "Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."
addedFE must use SCCA Part # WM803010 Brake Line to Control Arm covers if used, as delivered, fastened with zip ties or tape only.As printed in Fastrack
In FE, GCR section 9.1.1.G.2.K, add the following: "g. If used, SCCA Enterprises Part # WM803010 Brake Line to Control Arm covers must be used as delivered and must be securely fastened with zip ties/tie straps or tape. Part # WM803010 is the only approved part and may serve no other purpose."
STL Request to Remove Miata Hubs from General category
In GCR, Section 9.1.4.M.18., change as follows: "18. Allow alternate front wheel front hubs, Mazda Motorsports Development Part #0000-04-5HUB-S1, for the 90-05 Mazda Miata: Mazda Motorsports Development Part #0000-04-5HUB-S1."
Cal Club 2025 → Cal Club 2026 2025-02-22 to 2026-02-21
In SRF, GCR section 9.1.8.D.1.D, add the following: "f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
In STL Spec Lines, Table B, Mazda Spec MX5 Challenge, change as follows: Minimum Weight: "2500 See 9.1.7.1." Notes: "Mazda MX5 Challenge car must utilize the following components: Roush CNC cylinder head 0000-01-5300,Mahle standard or +0.005 0000-01-5310, OEM camshaft, 11:1 compression ratio, header 0000-06-5407-NC, exhaust 0000-06-5427-NC, cold air intake 0000- 06-5150-KT, ECU flash 0000-01-5379, Pagid front brake pads 0000-03-5104-SP or endurance pads 0000-03- 5104-EN, Pagid rear brake pads 0000-03-5114-SP or endurance pads 0000-03-5114-EN, Penske front shock 0000-04-5291-SA, Penske rear shock 0000-04-5292-SA, Penske rear mount kit 0000-04-5358, Front mount kit 0000-04-5359, Front offset bushing 0000-04-5407-NC, Eibach front springs 0000-04-9700-08, Eibach rear springs 0000-04-9400-07, Eibach helper springs 0000-04-
Show 5 more lines
9926, Eibach front sway bar 0000-04-5306-FT, Eibach rear sway bar 0000-04-5306-RR, Interior finish panels 0000-07-5822, C&R radiator/oil cooler assembly 0000-01-5504-CR, Oil cooler adapter and lines 0000-01-5511-KT, ACT clutch 0000-02-5004-G6, wheels 17x8 #0000-04-5706-GM, # 0000- 04-5706-SL, and Toyo RR 235-40-17 dry, Toyo RA1 235-40-17 wet. Alternative tires on 17x7 wheels per STL rules. No other Super Touring modifications or allowances permitted except as noted in this spec line. Must conform completely to GCR 9.1.7.1, except alternative tires (only) per STL regs allowed."
Applies to Mazda Miata on this page: Jared Korth, Ricardo Arruda, Gavin Wardle, Ryan Gutile, Bryce Johnson, Andy Chittum, Adrian Comstock
wordingFE2 minimum weight stays 1270 lbs; intake manifold part number changes to WM301061; ECU to G992012; mandatory spec parts expanded; bubble tail WM138014 now FE only; SADEV transmission no modifications allowed; brake rotor part numbers to W…As printed in Fastrack
Effective 9/1/25 in FE, GCR section 9.1.1.G.1.A, change as follows: "Definition FE’s with the Mazda 2.0L MZR engine will be classed as “FE2” and will use the class designation FE2. The Mazda 2.0L MZR motor can be used in all SCCA events. It shall run under all FE Preparation rules except as noted below: a. 2.0L MZR may be run with an Elite 5SPD or a Complete SADEV 6SPD transmission Kit Must use the following: b. 2.0L only Intake Manifold Part # WM30106 c. Throttle Body Part # WM591930-Jenvey d. PE ECU Kit Part # 1192012 e. Nippon-Denso Alternator Part # WM902127 f. Oil Filter Adaptor Part # WM301050 & Oil Filter Part # G301022 g. PCV Valve Part # WM391502 h. The car shall weigh 1270 lbs. minimum, including the driver. i. 16” MAZDA logo on each side of the engine cowling and the Mazda wing & name logo on the front center of the nose cone. These are mandatory decals. j. 2.0L MZR required Spark Plug Part# ND ITV 24 Formula Enterprises cars "FE" with Mazda 2.0L MZR engine are classed as "FE2." FE2 is the primary class in all SCCA events and must run under all FE Preparation rules except as noted below: Mandatory items 16” MAZDA logo, each side of the engine cowling, Mazda wing logo, front center of the nose cone. Table 2 (Spec Line Cars) Car Engine Wheel Width (in) ± .060 Aero Transmission Weight Notes
A specification table follows in the original; it is not shown here.
In SRF, GCR section 9.1.8.D.1.V.ff, change as follows: "SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
wordingFE adds engine modification restrictions, testing requirements, and drivetrain violation penalties with competition suspension.As printed in Fastrack
In FE, GCR section 9.1.1.G.2.G.a.1, add the following: "NO MODIFICATIONS ARE ALLOWED EXCEPT WHERE SPECIFICALLY AUTHORIZED WITHIN THESE RULES. This includes all fuel injection and engine management components, including exhaust, cooling, electrical and lubrication systems. All systems are subject to test procedures and must conform to OEM / SCCA Enterprises specifications as stated and supplied by Enterprises. All fluids, except fuel, are unrestricted." In FE, GCR section 9.1.1.G.2.T, add the following: "If a competitor refuses to give their engine and/or unlabeled parts for testing per a request of the Class Compliance Chief (CCC) or Chief Steward, the following penalties will automatically be imposed:" In FE, GCR section 9.1.1.G.2.T.d, add the following: "The car and drivetrain are suspended from competition until the unit(s) specified by the CCC or Chief Steward are replaced." In FE, GCR section 9.1.1.G.2.T, add a new section as follows: "g. Any drivetrain part found to be out of spec, during voluntary or involuntary inspection, will constitute a Drivetrain Violation. Penalties may be assessed post event."