This track has been raced on 4 configurations (Circuit, 2.57 mi; Classic 25 CCW, 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
FE has no laps in the events chosen. It ran at Super Tour Apr 2019, Super Tour Apr 2018, Super Tour Apr 2017: add those events.
SRF has no laps in the events chosen. It ran at Super Tour Apr 2017, Majors Apr 2016: add those events.
FM has no laps in the events chosen. It ran at Super Tour Apr 2019, Super Tour Apr 2018, Super Tour Apr 2017: add those events.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Van Diemen RF05
FC
1
1:11.935Peter West
1:11.935Peter West
Van Diemen RF99
FC
1
1:12.478Troy Shooter
1:12.478Troy Shooter
Van Diemen DP08
FC
1
1:14.576Gary Peterson
1:14.576Gary Peterson
Van Diemen RF01
FC
2
1:45.137Robert Armington
1:45.137Robert Armington
1:45.314Robert Armington
143.5Robert Armington
29.050Paul MacFarlane
30.109Robert Armington
45.728Robert Armington
Van Diemen DP-08
FC
1
1:45.137Robert Armington
1:45.137Robert Armington
1:45.314Robert Armington
143.5Robert Armington
29.106Robert Armington
30.109Robert Armington
45.728Robert Armington
Van Diemen RF01
FC
1
1:48.522Paul MacFarlane
1:50.067Paul MacFarlane
1:48.522Paul MacFarlane
114.4Paul MacFarlane
29.050Paul MacFarlane
31.137Paul MacFarlane
48.294Paul MacFarlane
Van Diemen RF96
FC
1
1:47.570Shawn Sarbacker
1:47.741Shawn Sarbacker
1:47.570Shawn Sarbacker
146.2Shawn Sarbacker
29.351Shawn Sarbacker
30.778Shawn Sarbacker
47.076Shawn Sarbacker
Van Diemen RF97
FC
1
1:47.993Bill Wallschlaeger
1:51.040Bill Wallschlaeger
1:47.993Bill Wallschlaeger
147.5Bill Wallschlaeger
29.638Bill Wallschlaeger
30.895Bill Wallschlaeger
47.233Bill Wallschlaeger
Van Diemen RF
FC
1
1:58.213Greg Pizzo
2:10.106Greg Pizzo
1:58.213Greg Pizzo
127.3Greg Pizzo
32.045Greg Pizzo
34.162Greg Pizzo
51.126Greg Pizzo
About this data
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Super Tour Feb 2023 → Super Tour Feb 2024 2023-02-24 to 2024-02-23
faster · engineSRF removes 1985 Renault Alliance solid front rotor option; restrictor sizes decrease 1mm for newer Kawasaki and multi-brand engines; minimum weights increase to 1100 lbs.As printed in Fastrack
In SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481"). The 1985 Renault Alliance solid front rotor (Reference: Bendix PRT1318 or Centrix 121.11004) may be used on front, rear, or both axles, but each axle must be paired to the same type rotor. The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038 may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind; maximum of one spring per caliper." P2 Engine Table Spec Line Engine Series
A specification table follows in the original; it is not shown here.
tyres & wheelsSRF wet front tyre changes to Hoosier P/N 46100 P185/60R13 H20 or W2 with 2.5" ground clearance.As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5" with driver as raced when P185/60R13 (H20 or W2) tires are used."
FC USF2000 Van Diemen with Mazda MZR LF-DE 2.0L in FC
addedUSF2000 Van Diemen with Mazda MZR LF-DE 2.0L added to FC as spec line car; removed from FX.As printed in Fastrack
RM 23-07, USF2000 Van Diemen with Mazda MZR LF-DE 2.0L in FC, GCR section 9.1.1.B.1, add a new section and re-letter the following sections accordingly: "c. The USF2000 tube frame Van Diemen car powered by the Mazda MZR LF-DE 2 liter engine is added as a "spec line" car in Formula Continental. Additional "spec line" cars are disfavored, and Balance of Performance (BoP) adjustments to keep "spec line" cars competitive with cars that meet the class formula are likewise disfavored." In FC, GCR section 9.1.1.B.11, add the following: "The only permitted engines are: a. The Ford 2 liter single overhead camshaft "NE" series engine or the 1971-74 Pinto/Capri 2 liter single overhead camshaft engine. The specifications are contained in B.15. b. The Ford Zetec ZX3 2 liter dual overhead camshaft engine. The specifications are contained in B.16. c. The Mazda MZR LF-DE 2 liter for use only in USF2000 cars, as described in the Spec Line Cars Table below." In FC, GCR section 9.1.1.B, add the following: In FX, GCR section 9.1.1.J.B, change as follows and renumber the remaining lines accordingly: "3. USF2000 (tube frame) – Shall comply with FRP F2000 Technical Specifications (2018) 4. Pro Formula F2000 (tube frame) – Engine must be prepared to current FC rules." In FX Table 1, remove the USF2000 Tube Frame and Pro Formula F2000 Tube Frame spec lines in their entirety. Spec Line Cars Table
A specification table follows in the original; it is not shown here.
wordingFC tire marking rule clarified: four dry and four wet tires for Regional/Major/Super Tour, eight each for Runoffs; undeclared tire penalty removed.As printed in Fastrack
In FC, GCR section 9.1.1.B.10.h, change as follows: "FC shall be is permitted a maximum of four (4) dry tires and four (4) wet tires for all Regional, Major, and Super Tour events; eight (8) dry tires and eight (8) wet tires are permitted for the Runoffs. This rule shall be is effective beginning with the first (1st) qualifying session of the event. Marked tires are not required for testing or practice. It is the competitor's responsibility to ensure that the tires are declared, marked, and logged by Tech in advance of the tire(s) being used in a qualifying session or race. Failure to participate on marked tires will result in a penalty. 1. Use of an undeclared tire shall automatically result in all times being disallowed in that session or finishing position in that race. 2. If a tire is damaged during a qualifying session or a race, the competitor may replace the damaged tire with a used tire upon approval by the Chief Steward without loss of time or finishing position. Second or subsequent damaged tires may similarly be replaced upon approval by the Chief Steward, however but such shall will result in the loss of grid position in the subsequent race or session; the competitor shall will start at the back of the grid. Replacement of a damaged tire with a new tire upon approval by the Chief Steward will result in loss of grid position in the subsequent race or session."
addedSRF radiator options expanded: Enterprises P/N 480465 with baffle 480464, 480466, or Automotive 1R698 and CU698 allowed if cross-reference equivalent.As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.V.j, change as follows: "Radiator - Enterprises new style P/N 480465 (requires baffle P/N 480464) or P/N 480466 can be used. P/N 480466, may can be replaced with Automotive P/N 1R698, CU698 or equivalent OEM manufacturer justified by one cross-reference chart equivalent, as long as the size, shape, and material are the same as the original P/N. The capacity, core thickness, etc., cannot be changed even if allowed under the above. The competitor is responsible for providing this documentation of the cross-reference P/N."
otherSRF rain/brake light must be Super Bright LEDs Inc. P/N PT-STRB-R24; secondary filament must connect to rain light switch.As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.W.l, change as follows: "A Super Bright LEDs Inc. rain / brake light comprised of a single standard trailer oval lamp, 2-1/4 inches x 6-1/2 inches, with incandescent or LED illumination, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the wiring harness. The secondary filament of the brake light assembly shall must be connected to a switch enabling its use as a rain light."
wordingFE rain light now must meet FIA Standard 8874-2019, Technical List No. 76, effective 1/1/2024.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.N.f, change as follows: "Any rain light is allowed. Effective 1/1/2024, a rain light that meets FIA Standard 8874-2019, Technical List No. 76, is required as specified in GCR section 9.3.32.B.2."
otherSRF brake light must be Super Bright LEDs Inc. P/N PT-STRB-R24, with SCCA Enterprises P/N 180427A pigtail and strobing rain light kit.As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.W.l, change as follows: "A Super Bright LEDs Inc. P/N PT-STRB-R24 (SCCA Enterprises P/N 180427A) rain / brake light, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the wiring harness. An SCCA Enterprises P/N 1190503 Strobing Brake Light Pigtail is required. The secondary filament of the brake light assembly must be connected to a switch enabling its use as a strobing rain light. A Strobing Brake Light Kit P/N 1168003 is available, which includes the brake light and pigtail."
In Cars and Equipment, GCR section 9.3.33.B.2, add the following: "(Effective 1/1/2024) A red taillight meeting FIA Standard 8874-2019, Technical List No. 76, is required on all Formula (open wheel) and Sports Racing cars." In Appendix F. Technical Glossary, Minimum Weight, change as follows: "Minimum Weight: – Weight specified with driver, exactly as they come off the race circuit, at the conclusion of any race or qualifying session." In FA Table 1, Spec Line E notes, add the following: "Any BD series iron or alloy cylinder block and alternate crankshaft permitted."
Show 8 more lines
In FC, GCR section 9.1.1.B.11.c, change as follows: "The Mazda MZR LF-DE 2 liter for use only in USF2000 cars, as described in the Spec Line Cars Table below."" In F600, GCR section 9.1.1.D.14, add the following: "Rotax Model 494, Model 493, and Model 593 must use a single expansion chamber and must be equipped with a pull starter; an electric starter may be added." In P1, GCR section 9.1.8.B.J.2, add the following: "Where a flat plate intake restrictor, restricted venturi, or Single Inlet Restrictor (SIR) is required, all intake air for each cylinder or the entire fuel-air mixture, if prepared before this point, must pass through the restrictor."
In SRF, GCR section 9.1.8.D.1.H, add the following: "NO MODIFICATIONS ALLOWED. Front brake ducts are required, attached to the openings in the lower radiator baffles, any flexible 4" duct material allowed, installed length minimum 12" maximum 36" in length. Must be securely fastened, Bracket Part # P/N 800368 can be used. Shall Must serve no other purpose. An extension may be welded to the side of the throttle pedal to improve heel-and-toe braking. Master cylinder casting / location must be used as delivered on P/N 180110 Pedal Mounting support. Aeroquip style -3 braided stainless flex lines only, must attach to all brake components without modification. Brake pad "anti-rattle" clips must be removed." In SRF, GCR section 9.1.8.D.1.V, add the following: "ii. Rear SADEV shift cable aluminum two-piece style clamp may be used. The P/N WM302007A clamp must serve no other purpose." In SRF, GCR section 9.1.8.D.1.X.k, add the following: "Negative camber shall must not exceed 5.0 degrees absolute maximum front and rear." In SRF, GCR section 9.1.8.D.1.AA.b, add the following: "2. Height of the radiator opening vertical surface 3 1/2“ +/- 1/2"." P2 Engine Table B.1 2008 and older Stock Suzuki, Yamaha, Honda, BMW 38.5mm P2 Engine Table B.2 Not required P2 Engine Table B.3 38.5mm Modified Engine 950 lbs. 1005cc max P2 Engine Table B.1 2008 and older 37mm P2 Engine Table B.2 Not required P2 Engine Table B.3 39mm Stock Engine 1050 lbs.
wordingFE allows racer's tape for crash repair, panel security, and heat exchanger opening control; seam taping banned.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.P.c, add the following: "Racer's tape may be used to repair crash damage, or as a precautionary means of securing the body panels or retaining latches fasteners only. Crash-damage is defined as having occurred during the current event, and the tape should be of an appropriate color if possible. Taping of body seams is not allowed. Taping across heat exchanger openings as a way to control temperature is allowed and may serve no other purpose."
Super Tour Feb 2024 → Super Tour Feb 2025 2024-02-23 to 2025-02-22
addedFC F2000 Metrik ZF2 added as spec line car with Brembo 4-piston calipers and vented rotors permitted.As printed in Fastrack
In FC Table FC Charts, add the following: In FC, GCR section 9.1.1.B.1.c, change as follows: "The USF2000 tube frame Van Diemen car powered by the Mazda MZR LF-DE 2 liter engine and the F2000 Metrik ZF2 car equipped with 4-piston calipers is are added as a "spec line" cars in Formula Continental. Additional "spec line" cars are disfavored, and Balance of Performance (BoP) adjustments to keep "spec line" cars competitive with cars that meet the class formula are likewise disfavored." FC Charts Car Engine Wheel Width (in) ± .060 Aero Transmission Weight Notes
A specification table follows in the original; it is not shown here.
addedFE requires five Hoosier decals: one small on nose or front shock cover, one 12" on each front wing plate, one 12" on each lower floor panel before rear wheels.As printed in Fastrack
In FE, GCR section 9.1.8.I.2.M, add the following: "b. Hoosier FE/FE2 Decal Placement: Five (5) "Hoosier" decals are required in the following locations: One (1) small "Hoosier" decal on the nose or the front shock cover of the car. One (1) 12" "Hoosier" decal on the outside vertical plane of each front wing plate. One (1) 12" "Hoosier" decal on the vertical plane of each of the lower floor panels just in front of the rear wheels. Hoosier decals are available, free of charge, from all Hoosier tire distributors and SCCA Enterprises."
SRF Update Rain Tire Rule and Hoosier Decal Placement
tyres & wheelsSRF wet tyres: front P185/60R13 H20 or W2 and rear P205/60R13 H20 or W2 removed; front P185/65R13 W2 and rear P205/60R13 W2 now required. Hoosier decal placement specified.As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used. OR Front – Hoosier P/N 46101 P185/65R13 W2 Rear – Hoosier P/N 46105 P205/60R13 W2 1. It is forbidden to regroove tires. 2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for violation will be the loss of qualifying times and/or the disqualification of race results. 3. Hoosier SRF/SRF3 Decal Placement: Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises."
wordingFE and SRF protest fee rules redirected to GCR section 8.3.1.D for fees and procedure.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.U.b.3, change as follows: "Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure." In SRF, GCR section 9.1.8.D.1.U.b.3, change as follows: "Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure. Item 1 will be done by the CSR or other shop that is equipped for this type of work and will be paid directly."
wordingFE and SRF protest fee rules redirected to GCR section 8.3.1.D for fees and procedure.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.U.b.3, change as follows: "Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure." In SRF, GCR section 9.1.8.D.1.U.b.3, change as follows: "Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure. Item 1 will be done by the CSR or other shop that is equipped for this type of work and will be paid directly."
SRF Update to Letter 36619 with new Hoosier Contingency Decal Info
wordingSRF Hoosier contingency decal requirement reduced from four decals in specific locations to three decals with simplified placement.As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows: "Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the front."
FE Update on Letter 36620 with new Hoosier Contingency Decal Info
wordingFE Hoosier contingency decal requirement reduced from five decals in specific locations to three decals on sides and front.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.M.b, change as follows: "Five (5) "Hoosier" decals are required in the following locations: One (1) small "Hoosier" decal on the nose or the front shock cover of the car. One (1) 12" "Hoosier" decal on the outside vertical plane of each front wing plate. One (1) 12" "Hoosier" decal on the vertical plane of each of the lower floor panels just in front of the rear wheels. Hoosier decals are available, free of charge, from all Hoosier tire distributors and SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the front."
suspension & brakesSRF Wilwood vented rotor minimum thickness increases to 13.25mm, 0.522 inches.As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."
wordingSRF3 Hoosier decal placement changed from four logos on nose and tail to three logos on sides and center front.As printed in Fastrack
In SRF, GCR section 9.1.8.D.2.B, change as follows: "Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."
wordingFC tire rule clarified: four dry and four wet tires for Regionals and Majors, eight each for Runoffs; marking and declaration timing adjusted.As printed in Fastrack
In FC, GCR section 9.1.1.B.10.h, change as follows: "(Effective 11/1/2024) FC is permitted a maximum of four (4) dry tires and four (4) wet tires for all Regional, Major, and Super Tour events; eight (8) dry tires and eight (8) wet tires are permitted for the Runoffs. This is effective beginning with the first (1st) qualifying session of the event. Marked tires are not required for The tire limit does not apply to testing or practice. It is the competitor's responsibility to ensure that the tires are declared, marked, and logged by Tech immediately upon conclusion of the first qualifying session, as provided in the event supplemental regulations, or per the instructions of the Race Director or Chief Steward. in advance of the tire(s) being used in a qualifying session or race. Failure to participate on marked Use of tires in excess of the number allowed will result in a penalty. Failure to participate on declared/marked/logged tires after the time prescribed for the same may result in a penalty. If a tire is damaged during a qualifying session or a race, the competitor may replace the damaged tire with a used tire upon approval by the Race Director or Chief Steward without loss of time or finishing position. Second or subsequent damaged tires may similarly be replaced upon approval by the Race Director or Chief Steward, but such will result in the loss of grid position in the subsequent race or session; the competitor will start at the back of the grid. Replacement of a damaged tire with a new tire upon approval by the Race Director or Chief Steward will result in loss of grid position in the subsequent race or session; the competitor will start at the back of the grid."
faster · weightFF and FC sequential gearbox weight penalty reduces from 25 lbs to 10 lbs minimum weight addition.As printed in Fastrack
In FF, GCR section 9.1.1.B.20.A.3, change as follows: "Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight." In FC, GCR section 9.1.1.B.20.B.4, change as follows: "Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
addedFE must use SCCA Part # WM803010 Brake Line to Control Arm covers if used, as delivered, fastened with zip ties or tape only.As printed in Fastrack
In FE, GCR section 9.1.1.G.2.K, add the following: "g. If used, SCCA Enterprises Part # WM803010 Brake Line to Control Arm covers must be used as delivered and must be securely fastened with zip ties/tie straps or tape. Part # WM803010 is the only approved part and may serve no other purpose."
Super Tour Feb 2025 → Super Tour Feb 2026 2025-02-22 to 2026-02-21
addedSRF drivers with disabilities may modify seat and controls for safety and comfort with SCCA approval, noted in logbook, for that driver only.As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.D, add the following: "f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
wordingFE2 minimum weight stays 1270 lbs; intake manifold part number changes to WM301061; ECU to G992012; mandatory spec parts expanded; bubble tail WM138014 now FE only; SADEV transmission no modifications allowed; brake rotor part numbers to W…As printed in Fastrack
Effective 9/1/25 in FE, GCR section 9.1.1.G.1.A, change as follows: "Definition FE’s with the Mazda 2.0L MZR engine will be classed as “FE2” and will use the class designation FE2. The Mazda 2.0L MZR motor can be used in all SCCA events. It shall run under all FE Preparation rules except as noted below: a. 2.0L MZR may be run with an Elite 5SPD or a Complete SADEV 6SPD transmission Kit Must use the following: b. 2.0L only Intake Manifold Part # WM30106 c. Throttle Body Part # WM591930-Jenvey d. PE ECU Kit Part # 1192012 e. Nippon-Denso Alternator Part # WM902127 f. Oil Filter Adaptor Part # WM301050 & Oil Filter Part # G301022 g. PCV Valve Part # WM391502 h. The car shall weigh 1270 lbs. minimum, including the driver. i. 16” MAZDA logo on each side of the engine cowling and the Mazda wing & name logo on the front center of the nose cone. These are mandatory decals. j. 2.0L MZR required Spark Plug Part# ND ITV 24 Formula Enterprises cars "FE" with Mazda 2.0L MZR engine are classed as "FE2." FE2 is the primary class in all SCCA events and must run under all FE Preparation rules except as noted below: Mandatory items 16” MAZDA logo, each side of the engine cowling, Mazda wing logo, front center of the nose cone. Table 2 (Spec Line Cars) Car Engine Wheel Width (in) ± .060 Aero Transmission Weight Notes
A specification table follows in the original; it is not shown here.
added · engineSRF3 adds HD Oil Cooler P/N G1148500 option alongside standard P/N G480503, no fan permitted.As printed in Fastrack
In SRF, GCR section 9.1.8.D.1.V.ff, change as follows: "SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
addedFC USF2000 Tube Frame may now use Hewland LD200 4-speed H-pattern as alternative to Hewland JL-200 5-speed sequential.As printed in Fastrack
In FC Charts table, USF2000 Tube Frame spec line, add the following to the Notes: "Cars originally built with the Hewland LD200 4-speed H-pattern may use that transmission as an alternative to the Hewland JL- 200 5-speed sequential transmission."
wordingFE adds engine modification restrictions, testing requirements, and drivetrain violation penalties with competition suspension.As printed in Fastrack
In FE, GCR section 9.1.1.G.2.G.a.1, add the following: "NO MODIFICATIONS ARE ALLOWED EXCEPT WHERE SPECIFICALLY AUTHORIZED WITHIN THESE RULES. This includes all fuel injection and engine management components, including exhaust, cooling, electrical and lubrication systems. All systems are subject to test procedures and must conform to OEM / SCCA Enterprises specifications as stated and supplied by Enterprises. All fluids, except fuel, are unrestricted." In FE, GCR section 9.1.1.G.2.T, add the following: "If a competitor refuses to give their engine and/or unlabeled parts for testing per a request of the Class Compliance Chief (CCC) or Chief Steward, the following penalties will automatically be imposed:" In FE, GCR section 9.1.1.G.2.T.d, add the following: "The car and drivetrain are suspended from competition until the unit(s) specified by the CCC or Chief Steward are replaced." In FE, GCR section 9.1.1.G.2.T, add a new section as follows: "g. Any drivetrain part found to be out of spec, during voluntary or involuntary inspection, will constitute a Drivetrain Violation. Penalties may be assessed post event."