No map published for Cal Club 2024, Cal Club 2023.
This track has been raced on 4 configurations (The Circuit, 2.57 mi; 19, 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.
FE has no laps in the events chosen. It ran at Super Tour Apr 2019, Super Tour Apr 2018, Super Tour Apr 2017: add those events.
FM has no laps in the events chosen. It ran at Super Tour Apr 2019, Super Tour Apr 2018, Super Tour Apr 2017: add those events.
SRF has no laps in the events chosen. It ran at Super Tour Apr 2017, Majors Apr 2016: add those events.
One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it.
Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.
Sectors
S1 SF → IM1 0.65 mi
S2 IM1 → IM2 0.75 mi
S3 IM2 → SF 1.17 mi
Spd In → Out 0.03 mi
Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.
By car
Car
Class
Drivers
Lap
Qual
Race
Trap
S1
S2
S3
Chevrolet Camaro
GT2
3
1:42.698Tim Carroll
1:42.698Tim Carroll
1:44.128Tim Carroll
149.2Jean Meynet
28.543Jean Meynet
29.839Tim Carroll
44.262Tim Carroll
Ford Mustang
GT2
1
1:45.818Brad McAllister
1:45.818Brad McAllister
1:46.926Brad McAllister
115.9Brad McAllister
28.729Brad McAllister
30.833Brad McAllister
45.847Brad McAllister
Dodge Challenger
GT2
1
1:46.922Ben Valentine
1:46.922Ben Valentine
1:47.171Ben Valentine
132.9Ben Valentine
29.689Ben Valentine
30.929Ben Valentine
45.990Ben Valentine
Porsche GT3
GT2
2
1:47.914Rocky Crocker
1:47.914Rocky Crocker
1:48.433Rocky Crocker
155.7Rocky Crocker
29.826Rocky Crocker
31.456Rocky Crocker
46.030Rocky Crocker
Porsche GT3
GT2
1
1:47.914Rocky Crocker
1:47.914Rocky Crocker
1:48.433Rocky Crocker
155.7Rocky Crocker
29.826Rocky Crocker
31.456Rocky Crocker
46.030Rocky Crocker
Porsche GT3 Cup
GT2
1
1:57.745Robert Kelley
1:57.745Robert Kelley
1:58.760Robert Kelley
125.1Robert Kelley
32.864Robert Kelley
33.998Robert Kelley
50.578Robert Kelley
Chevrolet Corvette
GT2
1
1:49.904Igor Lyustin
1:50.345Igor Lyustin
1:49.904Igor Lyustin
145.8Igor Lyustin
30.271Igor Lyustin
31.850Igor Lyustin
47.568Igor Lyustin
Mazda RX-7
GT2
3
1:51.013Guy Laidig
1:51.013Guy Laidig
1:52.486Guy Laidig
138.7Guy Laidig
30.134Guy Laidig
32.225Guy Laidig
47.907Guy Laidig
Dodge VIPER
GT2
1
1:57.753Robert Kelley
2:00.453Robert Kelley
1:59.538Robert Kelley
92.9Robert Kelley
31.983Robert Kelley
33.965Robert Kelley
51.553Robert Kelley
The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.
Rule changes between these events
Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23
In SRF, GCR section 9.1.8.D.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481"). The 1985 Renault Alliance solid front rotor (Reference: Bendix PRT1318 or Centrix 121.11004) may be used on front, rear, or both axles, but each axle must be paired to the same type rotor. The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N 1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other modification allowed. Wilwood caliper with bracket universal fit P/N 800038 may be used as delivered with no modification of any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind;
Show 4 more lines
maximum of one spring per caliper." P2 Engine Table Spec Line Engine Series
A specification table follows in the original; it is not shown here.
GT2 Adding Ginetta G56 GTA Factory ProTune for GT2 Class
In GT Cars - Porsche, classify Porsche Cayman ‘S’ as follows: GT Cars - Porsche Model Years Body Style Drive- line Wheel- base (in) Notes Porsche Cayman ‘S’ 09-12 2 dr. Coupe RWD 95.08 3.4L No PDK Transmission
addedFields Cardinal V8 added to GT1 with Ford V8 engine, 4.9L, 2100 lbs, fuel injection.As printed in Fastrack
In GT Spec Lines, GT1 Cars - Fields Cardinal, classify Fields Cardinal V8 as follows: GT1 Cars – Fields Cardinal Model Years Body Style Drive- line Wheel- base (in) Notes Fields Cardinal V8 2023 2 Dr. RWD 92.0 Roll Cage MUST be modified to comply with GCR Section 9.4. In GT Spec Lines, GT1Engines - classify Ford V8 as follows: GT1 Engines - Ford Engine Family Engine Type Bore x
A specification table follows in the original; it is not shown here.
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5" with driver as raced when P185/60R13 (H20 or W2) tires are used."
In GT2-ST Spec Lines, BMW E46 M3 & E36 / BMW Z3 / BMW 5000cc V8, change notes as follows: "The 3.4 liter 6 cyl. (87.0 bore x 93.0 stroke) is permitted at 2575lbs. 4.0L V8 permitted at 2900lbs. 4.5L V8 permitted at 2950lbs. 5.0L V8 permitted at 3000lbs. Flossman body kit permitted as found at http://www.racingpartsbmw.de/start/eng/start.htm. Trans Am SGT spec: Regular shifter 3000 lbs., paddle shifter plus 150 lbs. 95mm S54 crankshaft @ +150lbs. Lang Racing part# S54-95mm-StrokerCrk. S54 engine is permitted a 97mm stroke crankshaft (part #VAC-SC-S54) @2800lbs."
GT2 Remove Weight and Restrictor Penalty for Corvette C7 Body
In GT2 Spec Lines, Engines - MAZDA, combine both 20B to one spec lines and keep the following: Weight: "2500 2280" Notes: "Must run +100 lbs. for Grand Am transaxle and independent rear suspension. Must comply with all other GT2 rules."
In SRF, GCR section 9.1.8.D.1.V.j, change as follows: "Radiator - Enterprises new style P/N 480465 (requires baffle P/N 480464) or P/N 480466 can be used. P/N 480466, may can be replaced with Automotive P/N 1R698, CU698 or equivalent OEM manufacturer justified by one cross-reference chart equivalent, as long as the size, shape, and material are the same as the original P/N. The capacity, core thickness, etc., cannot be changed even if allowed under the above. The competitor is responsible for providing this documentation of the cross-reference P/N."
RM 23-10 GT2-ST Dodge Viper, incl Comp Coupe, ACR/ACR-X VRL Front Fascia As an Errors and omissions fix to what was originally intended for these cars, the Club Racing Board and Board of Directors have approved the following: In GT2-ST, Dodge Viper, incl Comp Coupe, ACR/ACR-X add VRL front fascia -100lbs to all Spec Lines.
GT2 Errors in GTCS Headings and Use of the Terms Category and ClassChange existing GTL and GTA Rules
wordingGTL spec lines moved contiguous with GT2 and GT3; GTA category and specs renumbered behind GTL; P2 engine tables reorganised with restrictor and weight specifications clarified.As printed in Fastrack
from the current (or before) Table of Contents (TOC), to what is shown in the after TOC. GTL spec lines will now be contiguous with GT2 and 3 spec lines. GTA category and spec lines will be moved and renumbered behind GTL. GTA Section will not change but page numbers will, (as shown in Red italics). 9.1.2.F. GT-2, 3, LITE Category Specifications 314 GT2 Cars 327 GT2/ST 341 GT3 Cars 348 GTL Cars 364 GTA Cars 377 P2 Engine Table B.1 2010 and older Stock Kawasaki 38.5mm minimum width 52 inches. AMAC-AM5: minimum width 54 inches. P2 Engine Table B.1 2008 and older Stock Engine Suzuki, Yamaha, Honda, BMW 38.5mm P2 Engine Table B.2 Not required P2 Engine Table B.3 38.5mm Modified Engine 950 lbs. 1005cc max P2 Engine Table B.1 37mm P2 Engine Table B.2 Not required P2 Engine Table B.3 39mm Stock Engine 1050 lbs.
In SRF, GCR section 9.1.8.D.1.W.l, change as follows: "A Super Bright LEDs Inc. rain / brake light comprised of a single standard trailer oval lamp, 2-1/4 inches x 6-1/2 inches, with incandescent or LED illumination, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the wiring harness. The secondary filament of the brake light assembly shall must be connected to a switch enabling its use as a rain light."
wordingFE rain light now must meet FIA Standard 8874-2019, Technical List No. 76, effective 1/1/2024.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.N.f, change as follows: "Any rain light is allowed. Effective 1/1/2024, a rain light that meets FIA Standard 8874-2019, Technical List No. 76, is required as specified in GCR section 9.3.32.B.2."
In SRF, GCR section 9.1.8.D.1.W.l, change as follows: "A Super Bright LEDs Inc. P/N PT-STRB-R24 (SCCA Enterprises P/N 180427A) rain / brake light, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the wiring harness. An SCCA Enterprises P/N 1190503 Strobing Brake Light Pigtail is required. The secondary filament of the brake light assembly must be connected to a switch enabling its use as a strobing rain light. A Strobing Brake Light Kit P/N 1168003 is available, which includes the brake light and pigtail."
In GT2-ST Spec Lines, Dodge Viper, incl Comp Coupe, ACR/ ACR-X change NOTES as follows: 8300 OEM: "Stock OEM engine. Engine long block, valve train, and intake system must meet stock, shop manual specifications. Hybrid update including Mopar Performance Part #P5156137. May use Mopar part #5038554AF (Gen 5 Intake Manifold manifold allowed with (2) 55mm flat plates) and 8.4L mechanical throttle body allowed. VRL Front Fascia -100lbs." 8300: "Hybrid update including Mopar Performance Part # P5156137, Mopar part #5038554AF manifold and 8.4L mechanical throttle body allowed using (2) 50 45mm flat plate restrictors. VRL Front Fascia –100lbs." 8400: "Intake and Throttle Body from Mopar Performance Part # P5156137allowed using (2) 50 45mm flat plate restrictors. , Mopar part #5038554AF manifold (Gen 5 Intake Manifold allowed with (2) 50mm flat plates) VRL Front Fascia -
Show 1 more lines
100lbs 8400 OEM 3225 Stock OEM engine. Engine long block."
In SRF, GCR section 9.1.8.D.1.H, add the following: "NO MODIFICATIONS ALLOWED. Front brake ducts are required, attached to the openings in the lower radiator baffles, any flexible 4" duct material allowed, installed length minimum 12" maximum 36" in length. Must be securely fastened, Bracket Part # P/N 800368 can be used. Shall Must serve no other purpose. An extension may be welded to the side of the throttle pedal to improve heel-and-toe braking. Master cylinder casting / location must be used as delivered on P/N 180110 Pedal Mounting support. Aeroquip style -3 braided stainless flex lines only, must attach to all brake components without modification. Brake pad "anti-rattle" clips must be removed." In SRF, GCR section 9.1.8.D.1.V, add the following:
Show 23 more lines
"ii. Rear SADEV shift cable aluminum two-piece style clamp may be used. The P/N WM302007A clamp must serve no other purpose." In SRF, GCR section 9.1.8.D.1.X.k, add the following: "Negative camber shall must not exceed 5.0 degrees absolute maximum front and rear." In SRF, GCR section 9.1.8.D.1.AA.b, add the following: "2. Height of the radiator opening vertical surface 3 1/2“ +/- 1/2"." P2 Engine Table B.1 2008 and older Stock Suzuki, Yamaha, Honda, BMW 38.5mm P2 Engine Table B.2 Not required P2 Engine Table B.3 38.5mm Modified Engine 950 lbs. 1005cc max P2 Engine Table B.1 2008 and older 37mm P2 Engine Table B.2 Not required P2 Engine Table B.3 39mm Stock Engine 1050 lbs.
wordingFE allows racer's tape for crash repair, panel security, and heat exchanger opening control; seam taping banned.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.P.c, add the following: "Racer's tape may be used to repair crash damage, or as a precautionary means of securing the body panels or retaining latches fasteners only. Crash-damage is defined as having occurred during the current event, and the tape should be of an appropriate color if possible. Taping of body seams is not allowed. Taping across heat exchanger openings as a way to control temperature is allowed and may serve no other purpose."
aeroGT1-GTX rear blade spoiler: angle 50–75°, max 59.0 wide by 5.0 high inches; total area limit removed.As printed in Fastrack
In GCR Section 9.1.2.G (GTA Category Specifications), change as follows: “9.1.2.G.III.I The single-plane rear spoiler must be mounted at an angel angle from 50 to 75 degrees (perpendicular to the ground being 90 degrees) and may not extend beyond the rear bumper when viewed from directly above the rear bumper. Spoilers must be a minimum of .063 aluminum or Lexan and may vary in overall height to match the contours of the bodywork. The rear spoiler dimensions shall not exceed 59.0 inches wide by 5.0 inches in height, (measured on the material surface) , or 295.0 square inches total surface area. Braces to prevent spoiler deflection are allowed, but may serve no other purpose.”
GT2 REDUCE C6 CORVETTE WEIGHT WITH OEM 7 LITER ENGINE REDUCE BY 150LB
added · engineGT1, GT2, GT3, GTL, GTX Direct Injection now permitted if original equipment.As printed in Fastrack
In GCR, Section 9.1.2.F.7.5.E. change as follows: “Direct Injection is not permitted only if it came OE and must be installed using only OE high pressure pump(s), hard and soft hoses and injectors.”
GT2 GT2/3 remove Direction Injection not allowed in Spec line notes
added · engineGT2 Nissan and GT3 Mazda, Mitsubishi 4G93, Nissan QR25DE/DD, QE25DE/DD now permit Direct Injection per 9.1.2.F.7.5.E.As printed in Fastrack
In GT2/3 modify Spec Line notes as follows: GT2: Nissan: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” GT3: Mazda: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” Mitsubishi 4G93: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E. ” Nissan QR25DE/DD 1988cc: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.” Nissan QE25DE/DD 2489cc: “Direct Injection not permitted, may be used per 9.1.2.F.7.5.E.”
Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22
In GT2 Spec Lines, GT Cars - MITJET ST, classify MITJET ST as follows: GT Cars – MITJET ST Model Years Body Style Drive- line Wheel- base (in) Notes MITJET ST 2015 RWD 94.5 Must run per VTS specifications. Must have
Show 2 more lines
complete car Specifications (FIA form CdM008) at every entered race event.
In GCR Section, Appendix K. 2012.M2, add the following: "After market replacement differential housings are permitted as long as they are an exact equivalent."
In 9.1.2. GT2 Spec Lines, GT3 Cars, change Note as follows: "Note: All GT4 cars are permitted to compete in GT2-ST provided they use a factory supplied power stick or Pro Series required restrictor. Must have GT4 rules in possession at all race events. Cars must comply with 2012 STO rules as stated in Appendix K of the GCR. Engine Displacements in this table are nominal. Each competitor shall have available definitive documentation (e.g., factory manual) of the original displacement for the engine used. Slicks allowed on all GT2/ST cars with a 100-pound weight penalty."
addedFE requires five Hoosier decals: one small on nose or front shock cover, one 12" on each front wing plate, one 12" on each lower floor panel before rear wheels.As printed in Fastrack
In FE, GCR section 9.1.8.I.2.M, add the following: "b. Hoosier FE/FE2 Decal Placement: Five (5) "Hoosier" decals are required in the following locations: One (1) small "Hoosier" decal on the nose or the front shock cover of the car. One (1) 12" "Hoosier" decal on the outside vertical plane of each front wing plate. One (1) 12" "Hoosier" decal on the vertical plane of each of the lower floor panels just in front of the rear wheels. Hoosier decals are available, free of charge, from all Hoosier tire distributors and SCCA Enterprises."
SRF Update Rain Tire Rule and Hoosier Decal Placement
In SRF, GCR section 9.1.8.D.1.X.f, change as follows: "Wet: Front – Hoosier P/N 46100 P185/60R13 H20 or W2 Rear – Hoosier P/N 46105 P205/60R13 H20 or W2 Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used. OR Front – Hoosier P/N 46101 P185/65R13 W2 Rear – Hoosier P/N 46105 P205/60R13 W2
Show 8 more lines
1. It is forbidden to regroove tires. 2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for violation will be the loss of qualifying times and/or the disqualification of race results. 3. Hoosier SRF/SRF3 Decal Placement: Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises."
wordingFE and SRF protest fee rules redirected to GCR section 8.3.1.D for fees and procedure.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.U.b.3, change as follows: "Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure." In SRF, GCR section 9.1.8.D.1.U.b.3, change as follows: "Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure. Item 1 will be done by the CSR or other shop that is equipped for this type of work and will be paid directly."
wordingFE and SRF protest fee rules redirected to GCR section 8.3.1.D for fees and procedure.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.U.b.3, change as follows: "Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure." In SRF, GCR section 9.1.8.D.1.U.b.3, change as follows: "Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure. Item 1 will be done by the CSR or other shop that is equipped for this type of work and will be paid directly."
SRF Update to Letter 36619 with new Hoosier Contingency Decal Info
In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows: "Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the front."
FE Update on Letter 36620 with new Hoosier Contingency Decal Info
wordingFE Hoosier contingency decal requirement reduced from five decals in specific locations to three decals on sides and front.As printed in Fastrack
In FE, GCR section 9.1.1.I.2.M.b, change as follows: "Five (5) "Hoosier" decals are required in the following locations: One (1) small "Hoosier" decal on the nose or the front shock cover of the car. One (1) 12" "Hoosier" decal on the outside vertical plane of each front wing plate. One (1) 12" "Hoosier" decal on the vertical plane of each of the lower floor panels just in front of the rear wheels. Hoosier decals are available, free of charge, from all Hoosier tire distributors and SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the front."
In SRF, GCR section 9.1.8.D.1.X.g, change as follows: "Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."
In SRF, GCR section 9.1.8.D.2.B, change as follows: "Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."
addedFE must use SCCA Part # WM803010 Brake Line to Control Arm covers if used, as delivered, fastened with zip ties or tape only.As printed in Fastrack
In FE, GCR section 9.1.1.G.2.K, add the following: "g. If used, SCCA Enterprises Part # WM803010 Brake Line to Control Arm covers must be used as delivered and must be securely fastened with zip ties/tie straps or tape. Part # WM803010 is the only approved part and may serve no other purpose."
In GT2 SPEC LINES, GT Engines - PANOZ, classify 2013-2016 Ford EcoBoost Twin Turbo as follows: GT Engines – PANOZ Engine Family Engine Type Bore x Stroke (in.) Disp.
Show 2 more lines
(CC) Head Type Valves /
A specification table follows in the original; it is not shown here.
wordingTA2 rear wing height rule clarified: OEM aerodynamic devices exempt from peak-of-roof height limit.As printed in Fastrack
In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows: "B. Aerodynamic Devices 2. Rear wing c. The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level with, or below, the peak of the roof. OEM aerodynamic devices do not need to adhere to the height rule."
A specification table follows in the original; it is not shown here.
In GCR, Appendix K. 2012 STO Rules, O.9., change as follows: "May run OEM ABS or convert to an aftermarket ABS controller with 100 50 lb. weight penalty."
Cal Club 2025 → Cal Club 2026 2025-02-22 to 2026-02-21
In GT2 Spec Lines, GT2 Cars - PONTIAC, Fiero, change as follows: Drive-line: "FWD RWD" Add to Notes: "Hood bulge permitted as requested for front engine relocation only."
In GCR, Section APPENDIX L. 2013 TA2 TECHNICAL REGULATIONS, B.2.c., change as follows: "The entire rear wing assembly, including the end plates and any Gurney flap, shall be mounted level with, or below, the peak of the roof. OEM aerodynamic devices do not need to adhere to the height rule." In GCR, Section APPENDIX K. 2012 STO GENERAL TECHNICAL REGULATIONS, D.4.b., add the following: "Factory wings, and spoilers, and roof vortex generators are permitted, but must be removed if an approved aftermarket wing is installed. OEM aerodynamic devices do not need to adhere to the height rule."
In SRF, GCR section 9.1.8.D.1.D, add the following: "f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard configuration."
In GT2 Spec Lines, GT2 Cars-Porsche, 911 Coupe & Targa., add to Notes the following: "Porsche 911-based race cars (911,963,994), the use of the 993 3.8 RSR rear deck lid/spoiler is permitted. Aftermarket reproductions of the original Porsche Motorsports deck lid provided they faithfully replicate OEM dimensions and functionality, are acceptable for use."
wordingFE2 minimum weight stays 1270 lbs; intake manifold part number changes to WM301061; ECU to G992012; mandatory spec parts expanded; bubble tail WM138014 now FE only; SADEV transmission no modifications allowed; brake rotor part numbers to W…As printed in Fastrack
Effective 9/1/25 in FE, GCR section 9.1.1.G.1.A, change as follows: "Definition FE’s with the Mazda 2.0L MZR engine will be classed as “FE2” and will use the class designation FE2. The Mazda 2.0L MZR motor can be used in all SCCA events. It shall run under all FE Preparation rules except as noted below: a. 2.0L MZR may be run with an Elite 5SPD or a Complete SADEV 6SPD transmission Kit Must use the following: b. 2.0L only Intake Manifold Part # WM30106 c. Throttle Body Part # WM591930-Jenvey d. PE ECU Kit Part # 1192012 e. Nippon-Denso Alternator Part # WM902127 f. Oil Filter Adaptor Part # WM301050 & Oil Filter Part # G301022 g. PCV Valve Part # WM391502 h. The car shall weigh 1270 lbs. minimum, including the driver. i. 16” MAZDA logo on each side of the engine cowling and the Mazda wing & name logo on the front center of the nose cone. These are mandatory decals. j. 2.0L MZR required Spark Plug Part# ND ITV 24 Formula Enterprises cars "FE" with Mazda 2.0L MZR engine are classed as "FE2." FE2 is the primary class in all SCCA events and must run under all FE Preparation rules except as noted below: Mandatory items 16” MAZDA logo, each side of the engine cowling, Mazda wing logo, front center of the nose cone. Table 2 (Spec Line Cars) Car Engine Wheel Width (in) ± .060 Aero Transmission Weight Notes
A specification table follows in the original; it is not shown here.
In SRF, GCR section 9.1.8.D.1.V.ff, change as follows: "SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."
GT2 Additional Body Options to Replace Older Stock Car Bodies
In GCR, Section 4.8.4.2.1., add the following: "Cars in the class must use 1997, through current year, commercially available stock car bodywork. The following make/model bodies are allowed: 1. Cadillac CTS 2. Chevrolet Impala 3. Chevrolet Malibu 4. Chevrolet Monte Carlo 5. Chevrolet SS
Show 12 more lines
6. Dodge Intrepid 7. Ford Fusion 8. Ford Taurus 9. Lincoln MKS 10. Pontiac G8 11. Pontiac GTO 12. Pontiac Grand Prix 13. Toyota Camry Gen late Model Stock Car Bodies are allows: 1. Chevrolet Camaro 2. Ford Mustang 3. Toyota Camry"
wordingFE adds engine modification restrictions, testing requirements, and drivetrain violation penalties with competition suspension.As printed in Fastrack
In FE, GCR section 9.1.1.G.2.G.a.1, add the following: "NO MODIFICATIONS ARE ALLOWED EXCEPT WHERE SPECIFICALLY AUTHORIZED WITHIN THESE RULES. This includes all fuel injection and engine management components, including exhaust, cooling, electrical and lubrication systems. All systems are subject to test procedures and must conform to OEM / SCCA Enterprises specifications as stated and supplied by Enterprises. All fluids, except fuel, are unrestricted." In FE, GCR section 9.1.1.G.2.T, add the following: "If a competitor refuses to give their engine and/or unlabeled parts for testing per a request of the Class Compliance Chief (CCC) or Chief Steward, the following penalties will automatically be imposed:" In FE, GCR section 9.1.1.G.2.T.d, add the following: "The car and drivetrain are suspended from competition until the unit(s) specified by the CCC or Chief Steward are replaced." In FE, GCR section 9.1.1.G.2.T, add a new section as follows: "g. Any drivetrain part found to be out of spec, during voluntary or involuntary inspection, will constitute a Drivetrain Violation. Penalties may be assessed post event."
In GT2 Spec Lines, GT2 Cars – Porsche, classify 992.1 GT3 Cup as follows: GT2 Cars – Porsche Model Year Body Style Driveline Wheel Base Notes 992.1 GT3 Cup (22-25) 2 Dr RWD 4.0L flat six. 3250lbs. w/60mm Throttle Body Restrictor (TBR). Cars must be prepared in accordance with the appropriate
Show 49 more lines
model/year Porsche factory 911 GT3 Cup parts catalog/service manual. Cars may not be altered in any way except as authorized below. Drivers must have the correct year manuals as they apply to their specific car in their possession. Safety, drivers comfort, driver control and instrumentation items may be modified per the GCR. Original factory installed Matter/ IMV roll cages are allowed. The stock unmodified fuel tank is allowed. Windshield clips must be installed per GCR 9.3 Windshield Clips/Rear Window Straps. All other SCCA safety standards apply. Tires per GCR 9.3 Tires. Lubricants, consumable fluids (brake fluid, coolant etc.) and oil filters are open free. Factory (OEM manufacturer) Lexan front windows allowed as delivered. ABS is allowed. In GT2 Spec Lines, GT2 Cars – Porsche, change Notes as follows: 991.1 GT3 Cup: "3.8L flat six. 3000lbs. w/72mm Throttle Body Restrictor (TBR). Aftermarket header allowed." 991.2 GT3 Cup: "4.0L flat six. 3000lbs. w/65mm 70mm Throttle Body Restrictor (TBR)." 997.2 GT3 Cup: "3.8L flat six. 2900 2800 lbs. Aftermarket header allowed." In GT2 Spec Lines, GT2 – ST, Chevy Corvette (-2013), change as follows: 5665: Restrictor: "81 85mm flat plate" Notes: "GM LS1, LS6. LS1/LS6 C6 Corvettes using the OEM C6 intake manifold and 90 mm throttle body must use a 78mm flat plate restrictor. OEM 75mm throttle body and manifold do not require a restrictor. LS6 may reduce weight by 50 lbs. L S1/LS6 alternate intake manifold, DORMAN part # 615-900." LS2 5967 Restrictor: "83 85mm " L76 5967 Restrictor: "80 83mm flat plate" LS3 6162 Restrictor: "80 83mm flat plate" 6162 GM LS3: Weight: "3250 3150" Restrictor: "74 80mm flat plate" 6162 GM LT1: Weight: "3250 3150" Restrictor: "74 77mm flat plate" In GT2 Spec Lines, GT2 – ST, Chevy Corvette (14-19), change as follows: 5665: Restrictor: "83 85mm flat plate" Notes: "GM LS1, LS6. LS1/LS6 C6 Corvettes using the OEM C6 intake manifold and 90 mm throttle body must use a 78mm flat plate restrictor. OEM 75mm throttle body and manifold do not require a restrictor. LS6 may reduce weight by 50 lbs. L S1/LS6 alternate intake manifold, DORMAN part # 615-900." LS2 5967: Weight: "3100 3000" Restrictor: "83 85mm flat plate" L76 5967 Restrictor: "80 83mm flat plate" 6162 Restrictor: "80 83mm flat plate" 6162 LS3: Weight: "3200 3100" Restrictor: "77 80mm flat plate" 6162 LT1: Weight: "3200 3100" Restrictor: "74 80mm flat plate"
GT2 Allow Larger Air Cooled Engines in Porsche 911 GT2
In GT Spec Lines, create GT Cars - PORSCHE and classify SC as follows: GT Cars - PORSCHE Model Years Body Style Drive- line Wheel- base (in) Notes SC 1978 2 Dr. Rear engine/RWD 89.45 May use alternate engine bore. 4.0L 2V @2275 lbs. 4.0L 4V @ 2350 lbs.
In GT Spec Lines, classify M3 E92 in GT Cars - BMW as follows: GT Cars - BMW Model Years Body Style Drive- line Wheel- base (in) Notes M3 E92 (08-13) 2 Dr. RWD 108.7 Cannot be built to any other rule set.
Show 5 more lines
In GT Spec Lines, classify M3 E92 in GT Engines - BMW - BMW as follows: GT Engines - BMW Engine Family Engine Type Bore x Stroke
A specification table follows in the original; it is not shown here.
What the rules allowed changed as listed; this does not say what any particular car ran.