FE + FB + FF at Buttonwillow Raceway Park

In FC/FF, GCR section 9.1.1.B.14.a.6, change as follows:
"For all Honda part numbers in these specifications, superc seding part numbers are considered equivalent.
In FC/FF, GCR section 9.1.1.B.14.f.5, change as follows:
"Cylinder head breather restrictor must be used as supplied by HPD or Fast Forward, unmodified.: HPD PN: 15262-F21S-A200; Fast
Forward PN: FF200-503."
In FC/FF, GCR section 9.1.1.B.14.k.2, change as follows:
"The upper manifold, air box and throttle body assembly must be used as delivered from Honda, HPD, or Fast Forward as noted
below."
In FC/FF, GCR section 9.1.1.B.14.k.2, insert as follows:
"a. Intake manifold: HPD PN: 17210-F21S-A210; Fast Forward PN: FF200-201.
b. Throttle body: Honda Fit: PN: 16400ZZ5024; HPD PN: 16400ZZ5024; Fast Forward PN: FF200-104.
c. Throttle lever: HPD PN: 17330-F21S-A210; Fast Forward PN: FF200-101."
In FC/FF, GCR section 9.1.1.B.14.k.3, change as follows:
"All gaskets and sensors utilized on the inlet manifold from head to throttle body must be Honda Fit OEM, or HPD supplied or Fast
Forward as noted below.
a. Gasket In. manifold: HPD PN: 17105-RB0-004, Honda Fit OEM.
b. Gasket, EGR chamber cover: HPD PN: 17146-RB0-004, Honda Fit OEM.
c. Gasket In. port: HPD PN: 17115-RB0-007, Honda Fit OEM.
d. Gasket, restrictor: HPD PN: 17399-F21S-A200, (2 required) HPD; Fast Forward PN: FF200-109. Two required."
In FC/FF, GCR section 9.1.1.B.14.k.5, change as follows:
"The Honda Fit engine is required to have an HPD supplied air inlet restrictor supplied by HPD or Fast Forward: HPD PN: 17344-
F21S-A201; Fast Forward PN: FF200-110, with internal diameter of 30.5mm and thickness of 3.175mm (0.125 inches) correctly
installed within the intake system."
In FC/FF, GCR section 9.1.1.B.14.m.1, change as follows:
"The exhaust manifold must be as supplied by HPD or Fast Forward:, HPD part # PN: 18150-F21S-A200 or # PN: 1818 50-F21S-B200;
Fast Forward PN: FF500-001 or PN: FF500-002."
In FC/FF, GCR section 9.1.1.B.14.n.1, change as follows:
"The oil pan, baffle plate, and scavenge pump filter fittings must be as supplied by HP or Fast Forward as noted below. No
modifications are permitted.
a. Oil pan: HPD PN: 11200-F21S-A210 or PN: 11200-F21S-C240; Fast Forward PN: FF100-201A or PN: FF100-201B.
b. Oil pan baffle plate: HPD PN: 11221-F21S-A210; Fast Forward PN: FF100-202.
c. Oil scavenge pump filter fittings (2 required): HPD PN: 15180-F21S-A210; Fast Forward PN: FF100-204."
In FC/FF, GCR section 9.1.1.B.14.n.3, change as follows:
"The scavenge pump and internal scavenge pump parts must be as supplied from HPD or Fast Forward as noted below."
In FC/FF, GCR section 9.1.1.B.14.n.3, change as follows:
"b. Rotor outside diameter: HPD 44.400mm (1.748 inches):; Fast Forward 40.640mm (1.600 inches).
c. Scavenge pump rotor set: HPD PN: 15450-F21S-A20; Fast Forward PN: FF100-110.
d. Oil pump: HPD PN: 15100-F21S-A200; Fast Forward PN: FF100-100A.
e. Scavenge pump cartridge: 15111-F21S-A21; Fast Forward PN: FF100-127.
f. Scavenge pump port A: HPD PN: 15137-F21S-A20; Fast Forward PN: FF100-101.
g. Scavenge pump port B: HPD PN: 15139-F21S-A20; Fast Forward PN: FF100-102.
h. Scavenge pump shaft: HPD PN: 15510-F21S-A20; Fast Forward PN: FF100-103.
i. Scavenge pump front cover: HPD PN: 15070-F21S-A21; Fast Forward PN: FF100-104."

In FE, GCR section 9.1.1.I.2.G.b.4.b, change as follows:
"(All SADEV ratios are under review and could be updated prior to sealing date)"

In FE, GCR section 9.1.1.I.2.N.f, change as follows:
"Any rain light is allowed. Effective 1/1/2024, a rain light that meets FIA Standard 8874-2019, Technical List No. 76, is required as
specified in GCR section 9.3.32.B.2."

In FE, GCR section 9.1.1.I.2.P.c, add the following:
"Racer's tape may be used to repair crash damage, or as a precautionary means of securing the body panels or
retaining latches fasteners only. Crash-damage is defined as having occurred during the current event, and the tape should be of
an appropriate color if possible. Taping of body seams is not allowed. Taping across heat exchanger openings as a way to control
temperature is allowed and may serve no other purpose."

In FF, GCR section 9.1.1.B.14.e.3.a, add the following:
"The standard ring pack, PN 13011-RB1-004 (Riken) or 13011-RB1-006 (Nippon), or the oversize ring pack, PN 13021-RB7-Z01
(Riken), or 13021-RB7-Z02 (Nippon), or FF800-100 (Fast Forward), may be used."

In FE, GCR section 9.1.8.I.2.M, add the following:
"b. Hoosier FE/FE2 Decal Placement:
Five (5) "Hoosier" decals are required in the following locations: One (1) small "Hoosier" decal on the nose or the front shock
cover of the car. One (1) 12" "Hoosier" decal on the outside vertical plane of each front wing plate. One (1) 12" "Hoosier" decal
on the vertical plane of each of the lower floor panels just in front of the rear wheels. Hoosier decals are available, free of charge,
from all Hoosier tire distributors and SCCA Enterprises."

In FE, GCR section 9.1.1.I.2.U.b.3, change as follows:
"Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure."
In SRF, GCR section 9.1.8.D.1.U.b.3, change as follows:
"Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure. Item 1 will be done by
the CSR or other shop that is equipped for this type of work and will be paid directly."

In FE, GCR section 9.1.1.I.2.M.b, change as follows:
"Five (5) "Hoosier" decals are required in the following locations: One (1) small "Hoosier" decal on the nose or the front shock
cover of the car. One (1) 12" "Hoosier" decal on the outside vertical plane of each front wing plate. One (1) 12" "Hoosier" decal
on the vertical plane of each of the lower floor panels just in front of the rear wheels. Hoosier decals are available, free of
charge, from all Hoosier tire distributors and SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to
qualify for contingency awards. One (1) decal must be located on each side of the car and one (1) decal must be visible on the
front."

In FF, GCR section 9.1.1.B.14.r.1, change as follows:
"All emission control devices must be removed and blocked off by the blanking plate provided by HPD or Fast Forward as noted
below, except for the VTEC activation valve. The VTEC activation valve must be retained; and it must be functioning. No
modifications are permitted.
a. EGR Plate: Fast Forward PN: FF200-301.
b. EGR Port Cover: Fast Forward PN: FF200-302."

In FF, GCR section 9.1.1.B.20.A.3, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."
In FC, GCR section 9.1.1.B.20.B.4, change as follows:
"Cars running with a sequentially shifted gear box shall must add 25 10 lbs. to minimum weight."

In FF, GCR section 9.1.1.B.14.e.1, change as follows:
"Honda Fit OEM standard size pistons, PN: 13010-RB1-000, or Honda Fit OEM 0.25mm oversize pistons, PN: 13020-RB7-Z00, or
Fast Forward 0.25mm oversize pistons, PN: FF800-110, may be used."
In GCR section 9.1.1.B.14.e.2, change as follows:
"a. Maximum standard piston diameter, measured at a point 16mm from the bottom of the skirt: 73.240mm
(2.8834 2.8835 inches).
b. Centerline of wrist pin to crown maximum: 26.21mm (1.032 inches).
c. Maximum overall height from skirt to crown edge: 47.80mm (1.882 inches).
d. Minimum weight: 198.0 grams (6.984 ounces).
e. Minimum weight of piston pin: 66 grams (2.25 ounces).
f. Combined minimum weight of piston, piston pin and connecting rod: 543.5 grams (18.85 ounces).
g. Combined minimum weight of piston, wrist pin, and circlips: 267 grams (9.418 ounces).
h. Centerline of wrist pin to crown edge: 26.289mm (1.035 inches).
i. Ring groove widths:
Top ring groove: 1.003mm (0.0395 inches).
Middle ring groove: 1.016mm (0.0400 inches).
Oil ring groove: 1.981mm (0.0780 inches).
j. Ring groove distance from wrist pin center to bottom of groove:
Top ring groove: 19.63mm (0.7730 inches).
Middle ring groove: 15.29mm (0.6020 inches).
Oil ring groove: 10.91mm (0.4295 inches)."

In FE, GCR section 9.1.1.G.2.K, add the following:
"g. If used, SCCA Enterprises Part # WM803010 Brake Line to Control Arm covers must be used as delivered and must be securely
fastened with zip ties/tie straps or tape. Part # WM803010 is the only approved part and may serve no other purpose."

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Formula F shall be limited to the following tires (front tires may not be used as rears):
Dries:
Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13
Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13
Wets:
Front - Hoosier Wet or W3 Radial 44421 185/60R13
Rear - Hoosier Wet or W3 Radial 44426 205/60R13
Alternatively, Formula F cars with rocker arm suspension (e.g., Swift DB1, 1987-90 Reynard) and/or outboard suspension on at
least one chassis end may use the following tires:
Dries:
Front - Hoosier H43130 R60A 20.0 x 6.0-13 or H43164 R60A 20.5 x 7.0-13 bias ply slick
Rear – Hoosier H43307 R60A 22.5 x 7.2-13 bias ply slick
Wets:
Radial wets listed above
or
Front - Hoosier 44165 135/545-13 VFF
Rear - Hoosier 44170 165/580-13 VFF
Front tires may not be used as rears, and tires may not be mixed, i.e., radial tires may not be mixed with bias ply slick tires, bias
ply slick tires may not be mixed with VFF tires, and radial tires may not be mixed with VFF tires."

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Formula F shall be limited to the following tires (front tires may not be used as rears):
Dries:
Front - Hoosier R60A Radial 43322 or F1600 Radial 43321 185/60R13
Rear - Hoosier R60A Radial 43327 or F1600 Radial 43326 205/60R13
Wets:
Front - Hoosier Wet or W3 Radial 44421 185/60R13
Rear - Hoosier Wet or W3 Radial 44426 205/60R13
Alternatively, Formula F cars with rocker arm suspension (e.g., Swift DB1, 1987-90 Reynard) and/or outboard suspension on at
least one chassis end may use the following tires:
Dries:
Front - Hoosier H43130 R60A 20.0 x 6.0-13 or H43164 R60A 20.5 x 7.0-13 bias ply slick
or
Hoosier 44165 135/545-13 VFF
Rear – Hoosier H43307 R60A 22.5 x 7.2-13 bias ply slick
or
Hoosier 44170 165/580-13 VFF
Wets:
Radial wets or VFF tires listed above
or
Front - Hoosier 44165 135/545-13 VFF
Rear - Hoosier 44170 165/580-13 VFF
Front tires may not be used as rears, and tires may not be mixed, i.e., radial tires may not be mixed with bias ply slick tires, bias
ply slick tires may not be mixed with VFF tires, and radial tires may not be mixed with VFF tires."

Effective 9/1/25 in FE, GCR section 9.1.1.G.1.A, change as follows:
"Definition
FE’s with the Mazda 2.0L MZR engine will be classed as “FE2” and will use the class designation FE2. The Mazda 2.0L MZR motor
can be used in all SCCA events. It shall run under all FE Preparation rules except as noted below:
a. 2.0L MZR may be run with an Elite 5SPD or a Complete SADEV 6SPD transmission Kit
Must use the following:
b. 2.0L only Intake Manifold Part # WM30106
c. Throttle Body Part # WM591930-Jenvey
d. PE ECU Kit Part # 1192012
e. Nippon-Denso Alternator Part # WM902127
f. Oil Filter Adaptor Part # WM301050 & Oil Filter Part # G301022
g. PCV Valve Part # WM391502
h. The car shall weigh 1270 lbs. minimum, including the driver.
i. 16” MAZDA logo on each side of the engine cowling and the Mazda wing & name logo on the front center of the nose cone.
These are mandatory decals.
j. 2.0L MZR required Spark Plug Part# ND ITV 24
Formula Enterprises cars "FE" with Mazda 2.0L MZR engine are classed as "FE2." FE2 is the primary class in all SCCA events and
must run under all FE Preparation rules except as noted below:
Mandatory items
16” MAZDA logo, each side of the engine cowling, Mazda wing logo, front center of the nose cone.
Table 2 (Spec Line Cars)
Car Engine
Wheel
Width
(in)
± .060
Aero Transmission Weight Notes

A specification table follows in the original; it is not shown here.

In FE, GCR section 9.1.1.G.2.F.k, change as follows:
"Enterprises bubble tail P/N: WM138014 is allowed for FE and is the only configuration for FE2."

In FF, GCR section 9.1.1.B.10.e, change as follows:
"Alternatively, Formula F cars with rocker arm suspension (e.g., 1987-90 Reynard, Swift DB1,) and/or outboard suspension on at
least one chassis end homologated in 1989 or earlier with any combination of rocker arm or outboard suspension on all four
corners (e.g., 1987 – 1990 Reynard, Swift DB1) may use the following alternative tires. Note: This rule is intended to allow older
cars with the described suspension design to use the alternative tires. It is not to be exploited by modifying cars with push-rods or
pull-rods to meet the above requirements or by modifying either end of older cars to push- or pull-rod suspension to be eligible to
run the alternative tires. Cars that were homologated in 1989 or earlier with push- or pull-rod suspension on no more than two
corners may seek approval to run the alternative tire by utilizing the compliance process outlined in GCR section 8.1.4."

In FE, GCR section 9.1.1.G.2.G.a.1, add the following:
"NO MODIFICATIONS ARE ALLOWED EXCEPT WHERE SPECIFICALLY AUTHORIZED WITHIN THESE RULES. This includes all fuel
injection and engine management components, including exhaust, cooling, electrical and lubrication systems. All systems are
subject to test procedures and must conform to OEM / SCCA Enterprises specifications as stated and supplied by Enterprises. All
fluids, except fuel, are unrestricted."
In FE, GCR section 9.1.1.G.2.T, add the following:
"If a competitor refuses to give their engine and/or unlabeled parts for testing per a request of the Class Compliance Chief (CCC)
or Chief Steward, the following penalties will automatically be imposed:"
In FE, GCR section 9.1.1.G.2.T.d, add the following:
"The car and drivetrain are suspended from competition until the unit(s) specified by the CCC or Chief Steward are replaced."
In FE, GCR section 9.1.1.G.2.T, add a new section as follows:
"g. Any drivetrain part found to be out of spec, during voluntary or involuntary inspection, will constitute a Drivetrain Violation.
Penalties may be assessed post event."