BoP Labbeta

BoP Lab / Buttonwillow Raceway Park

F5 + SRF + F500 + T2 at Buttonwillow Raceway Park

No mapCal Club 2024, Cal Club 2023

Track map: sectors and speed trap

Track map with timing sectors and speed trap
Shown for: Cal Club 2026 (practice, qualifying, race) · Cal Club 2025 (practice, qualifying, race)
Class · click a class to switch, + to compare alongside
Track configuration
Events

This track has been raced on 4 configurations (The Circuit, 2.57 mi; 19, 2.92 mi; 1.83 mi; 3.02 mi). Laps on different configurations are not comparable, so only events on the 2.57 mile layout are shown; switch above to see the others.

F5 has no laps in the events chosen. It ran at Super Tour Apr 2017: add that event.

SRF has no laps in the events chosen. It ran at Super Tour Apr 2017, Majors Apr 2016: add those events.

F500 has no laps in the events chosen. It ran at Cal Club 2022: add that event.

5 laps are left out as timing errors (far too short to be a lap of this track). The rest of those sessions, sectors included, is used.

PosCarDriverClass#LapTheoreticalQualRace5-lap stintConsistencyTrapS1S2S3
1Honda Civic TCRRylan HazeltonT2491:51.198 A-Q11:50.7631:51.198 A-Q11:51.454 A-R11:51.718 A-R1+1.803 A-R1140.1 A-R130.640 A-Q131.962 A-Q148.161 A-R1
2ChevroletOli Thordarson 2+ carsT2121, 1221:52.045 B-P1:51.9141:54.065 B-Q11:52.758 B-R11:53.593 B-R1+0.980 B-R1114.9 B-P30.654 B-P32.604 B-R148.656 B-P
3Chevrolet CorvetteJosh CarrollT2351:52.276 A-Q21:51.8961:52.276 A-Q21:52.993 A-R21:53.334 A-R2+1.248 A-R2144.5 A-Q230.813 A-Q232.300 A-Q148.783 A-P
4Chevrolet CorvetteDavid HolmesT21711:52.705 A-Q21:52.4891:52.705 A-Q21:53.499 A-R11:54.684 A-R2+1.099 A-R2143.9 A-Q230.883 A-Q132.407 A-Q249.199 A-Q2
5Chevrolet ChevroletOli Thordarson 2+ carsT21221:53.309 A-Q21:53.0511:53.309 A-Q21:54.433 A-R11:55.036 A-R2+0.674 A-R2142.9 A-R131.173 A-P32.798 A-Q149.080 A-P
6Chevrolet Corvette Z06Greg NesterT2321:53.653 A-Q21:53.5671:53.653 A-Q21:54.838 A-R11:55.189 A-R2+0.472 A-R2135.9 A-R131.106 A-Q232.902 A-Q249.559 A-Q2
7Chevrolet CorvettePatrick HoweT2031:53.679 A-P1:53.3731:54.829 A-Q11:55.392 A-R21:56.107 A-R2+1.043 A-R2146.6 A-Q231.124 A-Q133.112 A-Q149.137 A-P
8Chevrolet CorvetteEvan GoldT2371:53.749 A-R11:53.1551:53.792 A-Q21:53.749 A-R11:55.163 A-R2+0.789 A-R2138.7 A-Q131.295 A-R132.797 A-Q249.063 A-R1
9Chevrolet Corvette Z06Michael CheneyT2171:54.983 A-R21:54.4891:55.079 A-Q11:54.983 A-R21:55.791 A-R2+1.987 A-R2138.0 A-Q131.504 A-Q133.215 A-Q149.770 A-Q1
10Ford Mustang GTScotty B WhiteT201:55.309 A-Q11:55.2331:55.309 A-Q11:56.025 A-R11:56.446 A-R1+0.956 A-R1133.2 A-R131.540 A-Q133.554 A-R150.139 A-Q1
11Chevrolet C5 Z06Luis MartinezT2771:55.450 A-R11:54.5481:55.662 A-Q11:55.450 A-R11:56.522 A-R1+3.951 A-R1129.8 A-R1, A-Q231.045 A-R133.509 A-R149.994 A-R1

One row per driver and car (a driver who changed cars has a row for each). Each cell is that driver's best in that car across the selected events, with the session it was set in. Best 5-lap stint is the mean of the driver's quickest five consecutive race laps, and consistency is how far their median race lap sat behind their best in that race (small is a driver who does it every lap); both come from the race with the best stint. The fastest in each column is purple, and a car whose best lap is more than 115% of the fastest in its class is greyed (marked ">115%" beside the driver) and left out of the colour scale. Click a column to sort, a row to highlight it. Theoretical lap is the sum of the best sectors, whichever laps they came from, and never slower than the best lap (where a car's fastest laps were recorded without sector times, its best lap is used). The 115% mark is about the car's best lap only: a car whose best lap is within 115% of the fastest in its class is never marked. Greyed sectors with no theoretical lap mean the sector times on file do not add up to a believable lap. Letters refer to the events above; Q is qualifying, R a race.

Sectors

Sectors are numbered in lap order from start/finish, whatever each event's timing called them; the loop names are SCCA timing's.

By car

CarClassDriversLapQualRaceTrapS1S2S3
Honda Civic TCRT211:51.198Rylan Hazelton1:51.198Rylan Hazelton1:51.454Rylan Hazelton140.1Rylan Hazelton30.640Rylan Hazelton31.962Rylan Hazelton48.161Rylan Hazelton
ChevroletT211:52.045Oli Thordarson1:54.065Oli Thordarson1:52.758Oli Thordarson114.9Oli Thordarson30.654Oli Thordarson32.604Oli Thordarson48.656Oli Thordarson
Chevrolet CorvetteT271:52.276Josh Carroll1:52.276Josh Carroll1:52.993Josh Carroll146.6Patrick Howe30.813Josh Carroll32.300Josh Carroll48.783Josh Carroll
Chevrolet ChevroletT211:53.309Oli Thordarson1:53.309Oli Thordarson1:54.433Oli Thordarson142.9Oli Thordarson31.173Oli Thordarson32.798Oli Thordarson49.080Oli Thordarson
Ford MustangT211:55.309Scotty B White1:55.309Scotty B White1:56.025Scotty B White133.2Scotty B White31.540Scotty B White33.554Scotty B White50.139Scotty B White

The best any driver of each car managed across the selected events, with who set it. Spellings and model years of the same car are grouped; click a row marked ▸ to see each version. Grouping is worked out from the names, so tell us if two cars are wrongly merged or split.

Rule changes between these events

Cal Club 2023 → Cal Club 2024 2023-02-24 to 2024-02-23

SRF Update SRF Brake Rule

#33469 from Robey Clark · Rule change · TB 23-01 (2023-01 Fastrack)

In SRF, GCR section 9.1.8.D.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall be used as delivered with no
machining of any kind. Minimum thickness 12.20mm (0.481"). The 1985 Renault Alliance solid front rotor (Reference: Bendix
PRT1318 or Centrix 121.11004) may be used on front, rear, or both axles, but each axle must be paired to the same type
rotor. The Renault Alliance solid front rotors may not be used. Rubber caliper bushings may be replaced with bronze bushings P/N
1196185 or P/N 1196185. Original caliper pistons may be replaced with vented caliper piston P/N 1196184; no other
modification allowed. Wilwood caliper with bracket universal fit P/N 800038 may be used as delivered with no modification of
any kind. Wilwood knock back spring (2.63 lbs.) P/N 800045 may be used as delivered with no modification of any kind;

Show 4 more lines

maximum of one spring per caliper."
P2 Engine Table
Spec
Line Engine Series

A specification table follows in the original; it is not shown here.

T2 Honda Civic Type R Tire Size Increase

#33672 from Marty Grand · Rule change · TB 23-03 (2023-03 Fastrack)

In T2 Spec Lines, Honda Civic Type-R (2017-), change Tire Size as follows:
"275 295"

T2 Allowance of any nonmetallic bushing material in T2

#33833 from Tyler Quance · Rule change · TB 23-04 (2023-04 Fastrack)

In Touring (T2-T5) Category Specifications, GCR Section 9.1.9.2.D.5.c.1., change as follows:
"All T2-T3 cars are allowed to replace OEM upper and lower control arm bushings with polyurethane, or delrin, or alternate
synthetic materialbushings."

T2 Allow Adjustable stabilizer bar links

#33861 from John Heinricy · Rule change · TB 23-04 (2023-04 Fastrack)

In T2 Spec Lines, Cadillac CT4-V Blackwing (2022-), add to Notes as follows:
"Adjustable sway bar end links permitted."

T2 C5 Z06 Straight Line Speed

#33575 from Charlie Abell · Rule change · TB 23-05 (2023-05 Fastrack)

In T2 Spec Lines, Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04), change Weight (lbs) as follows:
"3425 w/53mm 56mm flat plate restrictor)
3350 (w/58mm flat plate restrictor, only permitted when using OEM Wheels and Stock Brakes)"

Applies to Chevrolet Corvette on this page: Josh Carroll, David Holmes, Patrick Howe, Evan Gold, Greg Nester, Michael Cheney, Luis Martinez

SRF Update SRF Front W2 Rain Tire Part Number

#34118 from Robey Clark · Rule change · TB 23-05 (2023-05 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Front – Hoosier P/N 46100 1 P185/65R13 W2"

T2 2009 Porsche Cayman Classing Request

#34147 from Lisa Hunsicker · Rule change · TB 23-06 (2023-06 Fastrack)

In T2 Spec Lines, Porsche Cayman S (06-08), change year as follows:
"Porsche Cayman S (06-08) (06-09)"

SRF Hoosier SRF Wet Front Tire Rule Update

#34189 from Robey Clark · Rule change · TB 23-06 (2023-06 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5" with driver as raced when P185/60R13 (H20 or W2) tires are used."

T2 370Z Obsolete Parts & NISMO Alternatives to SPL Parts

#34297 from Zach Hayward · Rule change · TB 23-06 (2023-05 Fastrack)

In T2 Spec Lines, Nissan 370Z (09-17) / 370Z NISMO Edition (09-17), change Notes as follows:
5300S-SS370 T-2 spring kit allowed; 54600-SS370 T-2 front and rear sway bar kit allowed. Sway Bars allowed 35mm (f). 29mm
(r). Sports Package is allowed. Springs up to 1000 lbs/in front and rear allowed. 54010- SZ350 (F) and 55020-SZ350 (R) allowed.
Cold Air Intake allowed. Performance Alternative Header permitted - Part #14002-SS370. Rear spring relocation permitted to
allow coil over shocks. SPL suspension kit permitted that includes: rear camber arms #SPL RLL Z34 or Nismo 551A0-RLLRZ, SPL
rear toe arms #SPL RTA Z34, SPL rear traction arms #SPL RTR Z34 or Nismo 55110-RTRRZ, SPL front camber arms #SPL FUA Z34 or
54525-FUAZ4, SPL rear mid link #SPL RML Z34 or Nismo 551B0-RMLZ4. Zspeed and Z1 alternative clutch slave permitted. The
following STOPTECH parts are allowed with a 50 Lb penalty: #83.488.6800.51 front, 83.657.0057.51 rear.

T2 Rules Clarification for Mazda RX8 Spec Line

#34395 from Colin Koehler · Rule change · TB 23-08 (2023-08 Fastrack)

In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change notes as follows:
"Use of 2009 R3 transmission is permitted with alternate gear ratios as listed. R3 transmission must be paired with the listed
alternate final drive. Front sway bar permitted 32mm MAX rear sway bar 19 MAX, Front springs max 750, 500 rear. Cold air
intake permitted. Header permitted. Aftermarket flywheel and single disc clutch permitted with no weight penalty."
In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), change notes as follows:
"Mazdaspeed radiator #0000-01-8501 allowed. Use of 2009 R3 transmission is permitted with alternate gear ratios as listed. R3
transmission must be paired with the listed alternate final drive. Mazdaspeed coil spring kit #QSEA-34-01Z allowed. 60mm flat
plate restrictor required. OE Rear spoiler allowed #F151-V4-920F. OE front air dam allowed #F151-V4-900f-BB. Springs Allowed:

Show 2 more lines

(F) Mazda Motorsports- 0000- 04-9700-08 or Eibach- 0800.250.0700 (R) Mazda Motorsports- 0000-04-9400-07 or Eibach
0700.250.0400, and helper 0000-04-9926 allowed. Alternate sway bars allowed max 32mm (f) 19mm (r)."

T2 rule book corrections

#34437 from Chi Ho · Rule change · TB 23-08 (2023-08 Fastrack)

In T3 Spec Lines, BMW 320i (14-15), add to Notes the following:
"Aftermarket intercooler permitted."
In T4 Spec Lines, BMW 320i (14-15), remove from Notes the following:
"Aftermarket intercooler permitted."

T2 Corvette LS2 Restrictor Plate Adjustment

#34456 from Brian LaCroix · Rule change · TB 23-08 (2023-05 Fastrack)

In T2 Spec Lines, Chevrolet Corvette C6 Coupe / Grand Sport (05-13), change Notes as follows:
"LS2: 58mm 60mm flat plate restrictor is required."

T2 Ride Height Correction for the T3 Solstice.

#34615 from Joe Aquilante · Rule change · TB 23-08 (2023-08 Fastrack)

In T2 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), add to Notes the following:
"Minimum ride height is 3 inches."
In T3 Spec Lines, Pontiac Solstice GXP Coupe / Convertible (07-09), add to Notes the following:
"Minimum ride height is 3 inches."

T2 Blacking Cadillac Fuel Capacity

#34624 from John Heinricy · Rule change · TB 23-08 (2023-05 Fastrack)

In T2 Spec Lines, Cadillac CT4-V Blackwing (2022-), add to Notes the following:
"Radium fuel surge tank permitted. Radium tank and all associated hoses must be located behind a fireproof bulkhead or in the
engine compartment."

SRF SRF Radiator Rule Update

#34805 from Robey Clark · Rule change · TB 23-10 (2023-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.V.j, change as follows:
"Radiator - Enterprises new style P/N 480465 (requires baffle P/N 480464) or P/N 480466 can be used. P/N 480466, may can be
replaced with Automotive P/N 1R698, CU698 or equivalent OEM manufacturer justified by one cross-reference chart equivalent,
as long as the size, shape, and material are the same as the original P/N. The capacity, core thickness, etc., cannot be changed
even if allowed under the above. The competitor is responsible for providing this documentation of the cross-reference P/N."

T2 M2 CS RACING

#35122 from Clark Giguiere · Rule change · TB 23-12 (2023-12 Fastrack)

In T2 Spec Lines, BMW M2 CS Cup 2020-, add to Notes the following:
"Hood vents conforming to 9.1.9.2.D.8.a.7 are permitted."

SRF Update SRF Rain / Brake Rule

#34706 from Robey Clark · Rule change · TB 23-09 (2023-09 Fastrack)

In SRF, GCR section 9.1.8.D.1.W.l, change as follows:
"A Super Bright LEDs Inc. rain / brake light comprised of a single standard trailer oval lamp, 2-1/4 inches x 6-1/2 inches, with
incandescent or LED illumination, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes
GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the
wiring harness. The secondary filament of the brake light assembly shall must be connected to a switch enabling its use as a rain
light."

SRF Update SRF Brake Light Rule v1

#34853 from Robey Clark · Rule change · TB 23-10 (2023-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.W.l, change as follows:
"A Super Bright LEDs Inc. P/N PT-STRB-R24 (SCCA Enterprises P/N 180427A) rain / brake light, P/N PT-STRB-R24, is required in the
original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No
changes may be made to the original 3-pin connector on the wiring harness. An SCCA Enterprises P/N 1190503 Strobing Brake
Light Pigtail is required. The secondary filament of the brake light assembly must be connected to a switch enabling its use as
a strobing rain light. A Strobing Brake Light Kit P/N 1168003 is available, which includes the brake light and pigtail."

T2 Rebalance Blackwing Cadillac T2

#35079 from John Heinricy · Rule change · TB 24-01 (2024-01 Fastrack)

In T2 Spec Lines, Cadillac CT4-V Blackwing (2022-), change as follows:
Wheel size: "(F) 18 x 10 (R) 18 x 11"
Notes: "Sway bars permitted 35mm (f), 30mm (r)"

T2 M2 CS RACING

#35130 from Clark Giguiere · Rule change · TB 24-01 (2024-01 Fastrack)

In T2 Spec Lines, BMW M2 CS Cup (2020-), change weight as follows:
"3600 3550"
In T2 Spec Lines, BMW M235iR (-2016), change weight as follows:
"3350 3300"

T2 Spec Corvette in T2

#35139 from David Sanders · Rule change · TB 24-01 (2024-01 Fastrack)

In T2 Spec Lines, Spec Corvette, change as follows:
Weight: "3375 3200"
Notes: "Cars must comply with all Spec Corvette rules dated 3-1-2 1 11-28-22 including fuel and tires. No tire treatment or
rubber softeners are permitted. T2 requirements of 3.75” min ride height and 53mm flat plate restrictor required. Any 295 DOT
tire approved with +200lb. Limited to 380 HP. Nankang NS-2R Tires conforming to Spec Corvette rules are required."

T2 T2 Viper BoP

#35155 from Scotty B White · Rule change · TB 24-01 (2024-01 Fastrack)

In T2 Spec Lines, Dodge Viper SRT-10 incl. coupe (03-06), change Tire Size as follows:
"(F) 315/35 (R) 345/30 335/30"

T2 BOP Adjustment for 5.0L Mustangs

#35156 from Kurt Rezzetano · Rule change · TB 24-01 (2024-01 Fastrack)

In T2 Spec Lines, Ford Mustang GT 5.0L (11-14), change as follows:
Min weight: "3500 3575"
Notes: "58mm 60mm flat plate restrictor required."
In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), change as follows:
Min Weight: "3600 3650"
Notes: "58mm 59mm flat plate restrictor required."
In T2 Spec Lines, Ford Mustang GT5.0L(2018-), change as follows:
Min Weight: "3600 3650"

Show 1 more lines

Notes: "55mm 58mm flat plate restrictor required."

Applies to Ford Mustang on this page: Scotty B White

T2 Take at Look at T-2 BOP

#35161 from Joe Aquilante · Rule change · TB 24-01 (2024-01 Fastrack)

In T2 Spec Lines, Chevrolet Camaro, 1LE (2016-), change as follows:
Min Weight: "3550 3500"
Notes: "56mm 58mm flat plate restrictor required."

T2 C5 Corvette Spec Line Oversight

#35169 from Carl Fung · Rule change · TB 24-01 (2024-01 Fastrack)

In T2 Spec Lines, Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04), change as follows:
Min Weight: :3425 w/56mm flat plate restrictor)"
Notes: "59mm flat plate restrictor required."
In T2 Spec Lines, Chevrolet Corvette C6 Coupe / Grand Sport (05-13) change Notes as follows:
"LS2: 60mm 63mm flat plate restrictor is required. LS3: 50mm 53mm flat plate restrictor is required."

Applies to Chevrolet Corvette on this page: Josh Carroll, David Holmes, Patrick Howe, Evan Gold, Greg Nester, Michael Cheney, Luis Martinez

T2 Requested Update of Model Years of 370Z

#35231 from Richard Kulach · Rule change · TB 24-01 (2024-01 Fastrack)

In T3 Spec Lines, Nissan 370Z (09-16) / 370Z NISMO Edition (09-13), change model as follows:
"Nissan 370Z (09-16) / 370Z NISMO Edition (09-13) ,incl. Nismo (2009-2022)"

SRF SRF / SRF3 Rule Updates

#35268 from Robey Clark · Rule change · TB 24-01 (2024-01 Fastrack)

In SRF, GCR section 9.1.8.D.1.H, add the following:
"NO MODIFICATIONS ALLOWED. Front brake ducts are required, attached to the openings in the lower radiator baffles, any
flexible 4" duct material allowed, installed length minimum 12" maximum 36" in length. Must be securely fastened, Bracket Part
# P/N 800368 can be used. Shall Must serve no other purpose. An extension may be welded to the side of the throttle pedal to
improve heel-and-toe braking. Master cylinder casting / location must be used as delivered on P/N 180110 Pedal Mounting
support. Aeroquip style -3 braided stainless flex lines only, must attach to all brake components without modification. Brake pad
"anti-rattle" clips must be removed."
In SRF, GCR section 9.1.8.D.1.V, add the following:

Show 23 more lines

"ii. Rear SADEV shift cable aluminum two-piece style clamp may be used. The P/N WM302007A clamp must serve no other
purpose."
In SRF, GCR section 9.1.8.D.1.X.k, add the following:
"Negative camber shall must not exceed 5.0 degrees absolute maximum front and rear."
In SRF, GCR section 9.1.8.D.1.AA.b, add the following:
"2. Height of the radiator opening vertical surface 3 1/2“ +/- 1/2"."
P2 Engine Table B.1
2008 and older Stock
Suzuki, Yamaha,
Honda, BMW
38.5mm
P2 Engine Table B.2 Not required
P2 Engine Table B.3 38.5mm
Modified
Engine
950 lbs.
1005cc max
P2 Engine Table B.1
2008 and older 37mm
P2 Engine Table B.2 Not required
P2 Engine Table B.3 39mm
Stock Engine
1050 lbs.

T2 2015+ Mustang Sway Bar and A-Arm Request

#35154 from Scotty B White · Rule change · TB 24-02 (2024-01 Fastrack)

In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), add to Notes the following:
"BMR rear upper control arm camber links part #UTCA064 permitted."

Applies to Ford Mustang on this page: Scotty B White

T2 Brake Kits

#35245 from David Woodle · Rule change · TB 24-02 (2024-01 Fastrack)

In T2 Spec Lines, add to Notes the following:
Chevrolet Camaro SS (98-02): “Four or six piston front calipers allowed.”
Chevrolet Camaro, 1LE (2016-): “Four or six piston front calipers allowed.”
Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04): “Four or six piston front calipers allowed.”
Chevrolet Corvette C6 Coupe / Grand Sport (05-13): “Four or six piston front calipers allowed.”
Chevrolet Corvette Z06 (06-12): “Four or six piston front calipers allowed.”
Pontiac Firebird (98-02): “Four or six piston front calipers allowed.”
Pontiac Solstice GXP Coupe/Convertible (07-09): “Four or six piston front calipers allowed.”

T2 More Car Lightening Stuff

#35319 from Scotty B White · Rule change · TB 24-02 (2024-02 Fastrack)

In GCR, Section 9.1.9.2.D.1.g.3., change as follows:
"Batteries may be replaced provided the replacement is capable of starting the car. Batteries may not be relocated
unless noted on the spec line. Batteries must be adequately secured. Battery labeling must conform to 9.3.35.D. with
those of an alternate manufacturer, provided they are of similar amp-hour capacity, size and within 10% of OEM
weight."

T2 Inclusion of B-C spec cars in T4

#35374 from Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)

In GCR, Section 9.1.9.2., change as follows:
"Touring car eligibility: Cars are eligible for the class they are listed with a specification line and with the specific
allowances permitted. In addition, T2-T4 cars may race one class up in touring classes above their specification line class
as long as they are a legal T2-T4 car and conform to their specification line allowances as classified. Cars conforming to
C-Spec rules are permitted to compete in Touring 4."

T2 Runoffs wording on Caddy in T2

#35377 from Touring Committee · Rule change · TB 24-02 (2024-01 Fastrack)

In T2 Spec Lines, Cadillac CT4-V Blackwing(2022-), change Notes as follows:
"THIS CAR DOES NOT QUALIFY FOR SCCA RUNOFFS COMPETITION UNTIL IT HAS BEENREPRESENTED IN 3 SCCA SUPER
TOUR EVENTS."

T2 T2-T4 Set expiration dates on spec lines

#35378 from Touring Committee · Rule change · TB 24-02 (2024-02 Fastrack)

In T2-T4 Spec Lines, add **This Spec line will expire 12/31/24, Please submit to appeal**
to Notes to the following Spec Lines:
T2:
Acura TL SHAWD (10-13)
Audi S4 (12-14)
Audi S5 (13-14)
Audi TT RS (2018-)
Cadillac ATS-V (16-17)

Show 46 more lines

Cadillac CTS-V (06-07)
Chevrolet Camaro SS (98-02)
Honda Civic (2017-)
Saturn Sky / Convertible (07-09)
Subaru Impreza WRX STi (03-07)
Subaru Impreza WRX STi (08-11)
T3:
Audi S4 (10-11)
Audi S4 (12-14)
Audi TTS Coupe (10-11)
Cadillac ATS (2015)
Chevrolet Cobalt (05-07)
Dodge SRT-4 (03-05)
Ford Fiesta ST (2014-)
Hyundai Genesis Coupe (2010-)
Hyundai Veloster Turbo (18-21)
Mazda RX-8 Base/R3/Sport/ GT (04-12)
Mini Cooper S (2016-)
Subaru WRX (02-05)
Toyota Camry (11-15)
T4:
Acura Integra GS-R VTEC (3 or 4 door) (94-01)
Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05)
BMW 320i (14-15)
Chevrolet Cobalt SS, Sport Coupe (06-10)
Chevrolet Sonic RS (2011-)
Chrysler/Dodge Neon ACR SOHC (4 door) (01-02)
Dodge Dart (14-15)
Dodge/Plymouth Neon ACR SOHC/DOHC (2/4 door) (95-99)
Fiat 500 Abarth (12-14)
Ford Focus SVT (02-04)
Ford Focus ZX4 ST (05-06)
Ford Focus (08-11)
Ford Mustang V-6 (01-04)
Honda Accord LX & EX (03-07)
Honda Accord LX-S/EX/EX-L (08-12)
Honda Civic Coupe Si (99-00)
Honda Civic SI (02-03)
Hyundai Elantra GLS (11-12)
Hyundai Tiburon V-6 (03-08)
Hyundai Veloster Turbo/ R-Spec (14-15)
Kia Forte Koup and Sedan LX/EX (10-13)
Kia Forte Koup and Sedan SX (10-13)
Kia Forte Koup (14-15)
Mazda Protégé ES (2000)
Mazda Protégé 5 (02-03)

T2 Reply to letter #35161 and #31661

#35384 from Andrew Aquilante · Rule change · TB 24-02 (2024-02 Fastrack)

In T2 Spec Lines, Chevrolet Camaro, 1LE (2016-), change as follows:
Min Weight: "3500 3575"
Notes: "58mm 60mm flat plate restrictor required"

Cal Club 2024 → Cal Club 2025 2024-02-23 to 2025-02-22

T2 Reorganize Spec Lines

#35375 from Touring Committee · Rule change · TB 24-03 (2024-03 Fastrack)

In T2-T4 Spec Lines, change Spec Line as follows:
"Wheel- base (mm) Required Restrictor"

T2 370Z Brake Rotor Size Correction

#35487 from Derek Chan · Rule change · TB 24-03 (2024-03 Fastrack)

In T2 Spec Lines, Nissan 370Z (09-17) / 370Z NISMO Edition (09-17), change Brakes (mm) as follows:
"(F)320 x 28 Vented R)320 x 16 Vented : (F) 355x32mm Vented(R) 350x20mm Vented”
In T3 Spec Lines, Nissan 370Z, incl. Nismo (2009-2022), change Brakes (mm) as follows:
"(F)320 x 28 Vented (R)320 x 16 Vented : (F) 355x32mm Vented(R) 350x20mm Vented”

T2 Letter #35154 2018+ Mustang GT Expansion

#35488 from Michael Kamalian · Rule change · TB 24-03 (2024-03 Fastrack)

In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows:
"BMR rear upper control arm camber links part #UTCA064 permitted."

Applies to Ford Mustang on this page: Scotty B White

T2 Brake Request for 2009 Porsche Cayman

#35723 from Jason Ott · Rule change · TB 24-04 (2024-04 Fastrack)

In T2 Spec Lines, Porsche Cayman S (06-09), add to Notes the following:
"The following brake kit is allowed in its entirety with a 50 lb penalty- (f) StopTech ST60 (83.788.6700), rotor size 355X32
(r) StopTech ST40 (83.799.0046), rotor size 332X32."

T2 Allow T4 and T3 RX8 to Disable/Remove Factory Oil Inj.

#35761 from David Mead · Rule change · TB 24-05 (2024-05 Fastrack)

In T3 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows:
"OEM oil injection system may be removed or disabled."
In T4 Spec Lines, Mazda RX-8 Base/R3/Sport/ GT (04-12), add to Notes as follows:
"OEM oil injection system may be removed or disabled."

T2 Competition Adjustment Request/Wheel Size of E46

#35895 from David Newman · Rule change · TB 24-05 (2024-05 Fastrack)

In T2 Spec Lines, BMW M3 (01-06), change Max Wheel Size (inch) as follows:
"18 x 9 18 x 10"

T2 Driveshafts

#35916 from Scotty B White · Rule change · TB 24-05 (2024-05 Fastrack)

In GCR Section 9.1.9.2.D.4.b., add the following:
"6. T2-T3- Driveshafts may be replaced with alternative materials ie. carbon fiber, aluminum, steel. Two-piece driveshafts may
be replaced with one-piece units. If non-OEM driveshaft is used, add 25 lbs."

T2 Mustang T2/T3

#35877 from Scotty B White · Rule change · TB 24-07 (2024-07 Fastrack)

In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), add to Notes as follows:
"Track/Performance Package parts permitted."
In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows:
"Track/Performance Package parts permitted."
In T3 Spec Lines, Ford Mustang V6 (15-17), change Notes as follows:
"Track/Performance package allowed."

Applies to Ford Mustang on this page: Scotty B White

T2 S550 Brakes

#35926 from Scotty B White · Rule change · TB 24-07 (2024-07 Fastrack)

In T2 Spec Lines, Ford Mustang Ecoboost 2.3 (2015-), add to Notes the following:
"100LB for Mustang S550 2015-17 5.0 Gen2 and 2018-23 5.0. Gen3 reduce weight by 100Lb when using 4 piston stock
or Brembo brakes with 355mm rotors."

T2 T2-T4 Driveshaft Mistake...?

#36050 from Scotty B White · Rule change · TB 24-07 (2024-07 Fastrack)

In GCR Section 9.1.9.2.D.4.b.6., remove as follows:
"If non-OEM driveshaft is used, add 25 lbs."
In T2 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows:
"Driveshaft from Alternate metallic driveshaft is allowed."
In T2 Spec Lines, Ford Mustang Boss 302 (12-13), change Notes as follows:
"Alternate metallic driveshaft is allowed."
In T2 Spec Lines, Ford Mustang GT 5.0L (11-14)ki, change Notes as follows:
"Alternate metallic driveshaft is allowed."

Show 12 more lines

In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), change Notes as follows:
"Alternate metallic driveshaft is allowed."
In T2 Spec Lines, Ford Mustang GT 5.0L (2018-), change Notes as follows:
"Alternate metallic driveshaft is allowed."
In T2 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L (05-10), change Notes as follows:
'An Aluminum driveshaft is allowed."
"Alternate metallic driveshaft is allowed."
In T3 Spec Lines, Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10), change Notes as follows:
"An Aluminum driveshaft is allowed."
"Alternate metallic driveshaft is allowed."
In T3 Spec Lines, Ford Mustang V6 (11-14), change Notes as follows:
"Driveshaft from Alternate metallic driveshaft is allowed."

Applies to Ford Mustang on this page: Scotty B White

T2 request for allowance of 6 piston calipers for T2 C5 corvettes

#36126 from Joe Aquilante · Rule change · TB 24-07 (2024-07 Fastrack)

In T2 Spec Lines, add to Notes the following:
Chevrolet Camaro SS (98-02): Four or six piston front calipers allowed.
Chevrolet Camaro, 1LE (2016-): Four or six piston front calipers allowed.
Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04): Four or six piston front calipers allowed.
Chevrolet Corvette C6 Coupe / Grand Sport (05-13): Four or six piston front calipers allowed.
Chevrolet Corvette Z06 (06-12): Four or six piston front calipers allowed.
Pontiac Firebird (98-02): Four or six piston front calipers allowed.
Pontiac Solstice GXP Coupe/Convertible (07-09): Four or six piston front calipers allowed.

T2 B8/8.5 Audi S4 T3 and T2

#36195 from Brian Leib · Rule change · TB 24-07 (2024-07 Fastrack)

In T3 Spec Lines, Classify Audi S4 (2000-2002) as follows and allow the T2 spec line to expire.

A specification table follows in the original; it is not shown here.

T2 Errors

#36214 from Touring Committee · Rule change · TB 24-08 (2024-08 Fastrack)

In T2 Spec Lines, Chevrolet Corvette C6 Coupe / Grand Sport (05-13), change Required Restrictor as follows:
"LS2: "53 63mm flat plate restrictor"
In T2 Spec Lines, Chevrolet Camaro, 1LE (2016-), change as follows:
Min Weight: "3575 3500"
Required Restrictor: "60mm FRP 58mm flat plate restrictor"

T2 Subaru Appeal

#36258 from Anthony Piselli III · Rule change · TB 24-08 (2024-08 Fastrack)

In T2 Spec Lines, Subaru Impreza WRX STi (03-07), change Notes as follows:
"**This Spec line will expire 12/31/24, Please submit to appeal**"
In T2 Spec Lines, Subaru Impreza WRX STi (08-11), change Notes as follows:
"**This Spec line will expire 12/31/24, Please submit to appeal**"

SRF Update Rain Tire Rule and Hoosier Decal Placement

#36436 from Robey Clark · Rule change · TB 24-08 (2024-08 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used.
OR
Front – Hoosier P/N 46101 P185/65R13 W2
Rear – Hoosier P/N 46105 P205/60R13 W2

Show 8 more lines

1. It is forbidden to regroove tires.
2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for
violation will be the loss of qualifying times and/or the disqualification of race results.
3. Hoosier SRF/SRF3 Decal Placement:
Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to
the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the
rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including
SCCA Enterprises."

T2 S550 Brakes

#36571 from Club Racing Board · Rule change · TB 24-08 (2024-08 Fastrack)

In T2 Spec Lines, Ford Mustang GT 5.0L (15-17), add to Notes as follows:
"Mustang S550 2015-17 5.0 Gen2 and 2018-23 5.0. Gen3 reduce weight by 100Lb when using 4 piston stock or Brembo brakes
with 355mm rotors."
In T2 Spec Lines, Ford Mustang GT 5.0L (18 -), add to Notes as follows:
"Mustang S550 2015-17 5.0 Gen2 and 2018-23 5.0. Gen3 reduce weight by 100Lb when using 4 piston stock or Brembo brakes
with 355mm rotors."
In T2 Spec Lines, Ford Mustang Ecoboost 2.3 (2015-), change Notes as follows:
"Reduce weight by 100Lb when using either stock 355mm 4 piston brakes or m2300s 355mm 4 piston Ford brake kit."

Applies to Ford Mustang on this page: Scotty B White

SRF Protest Fee Clarification

#36540 from SCCA Staff · Rule change · TB 24-09 (2024-09 Fastrack)

In FE, GCR section 9.1.1.I.2.U.b.3, change as follows:
"Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure."
In SRF, GCR section 9.1.8.D.1.U.b.3, change as follows:
"Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure. Item 1 will be done by
the CSR or other shop that is equipped for this type of work and will be paid directly."

SRF Update to Letter 36619 with new Hoosier Contingency Decal Info

#36624 from Robey Clark · Rule change · TB 24-09 (2024-09 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows:
"Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose
to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the
rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including
SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1)
decal must be located on each side of the car and one (1) decal must be visible on the front."

SRF Update SRF3 Air Filter Rule

#36681 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.2.H.23, change as follows:
"Air Filter: P/N WM301020 or K&N RC-9160"

SRF Update SRF Brake Rotor Thickness

#36687 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with
no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."

SRF Hoosier Tire Decal Placement

#36739 from Robey Clark · Rule change · TB 24-10 (2024-10 Fastrack)

In SRF, GCR section 9.1.8.D.2.B, change as follows:
"Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the
nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."

T2 Spec Corvette Change for T2

#37127 from Joe Aquilante · Rule change · TB 24-11 (2024-11 Fastrack)

In T2 Spec Lines, Spec Corvette, change Notes as follows:
"Cars must comply with all Spec Corvette rules dated 11-28-22 including fuel and tires. No tire treatment or rubber softeners are
permitted. Limited to 380 HP. Nankang NS-2R Tires conforming to Spec Corvette rules are required or a 295 R compound DOT
tire."

T2 Redundant Verbiage Regarding Mustang Spec Lines for Driveshaft

#36484 from David Mead · Rule change · TB 24-12 (2024-12 Fastrack)

In T2 Spec Lines, change Notes as follows:
Ford Mustang V6 (11-14): "Alternate driveshaft is allowed."
Ford Mustang Boss 302 (12-13): "Alternate driveshaft is allowed."
Ford Mustang GT 5.0L (11-14): "Alternate driveshaft is allowed."
Ford Mustang GT 5.0L (15-17): "Alternate driveshaft is allowed."
Ford Mustang GT 5.0L (2018-): "Alternate driveshaft is allowed. Springs up to 800#/in front and rear permitted. Alternate
metallic driveshaft permitted."
Ford Mustang Coupe GT & Shelby GT 4.6L (05-10): "Alternate driveshaft is allowed."

Show 4 more lines

In T3 Spec Lines, change Notes as follows:
Ford Mustang Coupe GT & Shelby GT 4.6L & Cal. Special (05-10): "Alternate driveshaft is allowed."
Ford Mustang V6 (11-14): "Alternate driveshaft is allowed."
Ford Mustang V6 (05-10): "An Aluminum driveshaft is allowed."

T2 Request Less Restriction for Ls-3 Engined C6 Corvette

#36810 from Joe Aquilante · Rule change · TB 24-12 (2024-12 Fastrack)

In T2 Spec Lines, Chevrolet Corvette C6 Coupe / Grand Sport (05-13), change Restrictor Required as follows:
"LS3: 53mm 56mm flat plate restrictor"

T2 Fuel Emissions Components

#37076 from Derrick Ambrose · Rule change · TB 24-12 (2024-12 Fastrack)

In GCR, Section 9.1.9.2.D.1.c. add the following:
"5. Removal of ancillary fuel tank equipment charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket
fuel cell installations."

T2 fix brake wording

#37129 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

In GCR, Section, 9.1.9.2.D.6. Brakes, change as follows:
"a. Components
1. The make and material of brake pads and linings may be changed.
2. Brake fluid may be substituted with any brake fluid.
3. Brake rotor dust shields may be removed or replaced to accommodate brake ducts.
4. Flexible rubber brake lines may be replaced with Teflon lined, metal braided hoses.
5. Any brake ducts are permitted, but they must serve no other purpose. Fender liners may be modified solely for routing and
attachment of brake ducts. Duct intake openings may be created by the opening of 2 sections up to 14.5 square inches each in

Show 10 more lines

the front fascia. The stock headlamp location is not permitted for brake ducting. Two alternative duct openings may be created
by the removal of the fog lights or 2 sections up to 14.5 square inches each of stock false grills originally located in the front
fascia.
6. Stock replacement brake rotors may be obtained from sources other than the manufacturer provided they are the exact
equivalent of the stock rotors. In T2 only - 2-piece rotors with ferrous metal rotor disks and aluminum hats are allowed, must be
within 5% of OE diameter. In T3 only - 2-piece front rotors with ferrous metal rotor disks and aluminum hats are allowed, must
be within 2% of OEM diameter. Drilled and slotted rotors are permitted.
7. Parking brakes, mechanisms, and actuating components may be removed.
8. Brake vacuum reservoirs sized 0.50 gallons or smaller are permitted. The port or fitting at the vacuum source may not be
modified, enlarged or relocated. The vacuum reservoir and brake booster must be a closed system."

T2 Evaporative emissions systems

#37130 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

In GCR, Section, 9.1.9.2.D.1.c., add the following:
"5. Removal of ancillary fuel tank equipment; charcoal canisters, emissions valves, and sensors allowed for OEM or aftermarket
fuel cell installations."

T2 Move Spec Boxster to T4

#37158 from Rob Piekarczyk · Rule change · TB 24-12 (2024-12 Fastrack)

In T4 Spec Lines, classify Porsche Spec Boxster, as follows:

A specification table follows in the original; it is not shown here.

T2 Corvette Wheels

#37169 from Brian LaCroix · Rule change · TB 24-12 (2024-12 Fastrack)

In T2 Spec Lines, Chevrolet Corvette C6 Coupe / Grand Sport (05-13), change Max Wheel Size as follows:
"18 x 10 11 (F) 19 x 11 (R) or 18 x 11 (F) 19 x 13 (R)"

T2 BMW 320i Spec Line

#37204 from chi ho · Rule change · TB 24-12 (2024-12 Fastrack)

In T4 Spec Lines, BMW 320i (14-15), change Notes as follows:
"**This Spec line will expire 12/31/24, Please submit to appeal** Turner Motorsports intercooler #024703TMS02 allowed."

T2 Classification for a 2005 Cadillac CTS 3.6 liter 6 speed manual

#37224 from Timothy Nash · Rule change · TB 24-12 (2024-12 Fastrack)

In T3 Spec Lines, classify Cadillac CTS (02-07) as follows:

T2 Please Consider Allowing Update to the C5 Corvette

#37298 from DAVID WOODLE · Rule change · TB 24-12 (2024-12 Fastrack)

In T2 Spec Lines, Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04), change Restrictor Required as follows:
"59mm FRP LS1: 59mm FPR, LS2: 63mm FPR, LS3: 56mm FPR"

Applies to Chevrolet Corvette on this page: Josh Carroll, David Holmes, Patrick Howe, Evan Gold, Greg Nester, Michael Cheney, Luis Martinez

T2 Major error in lane, but nobody ran it.

#37302 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

In T2 Spec Lines, delete Chevrolet Corvette Z06 (06-12) Spec Line in its entirety.

T2 BoP for the Various Mustangs

#37185 from Scotty B White · Rule change · TB 25-01 (2025-01 Fastrack)

In T2 Spec Lines, Ford Mustang GT 5.0L (11-14), change as follows:
Weight: "3575 3525"

Applies to Ford Mustang on this page: Scotty B White

T2 Remove spec lines that have expired

#37269 from Touring Committee · Rule change · TB 24-12 (2024-12 Fastrack)

In T2, Effective 1/1/2025, delete for following Spec Lines in their entirety:
"Acura TL SHAWD (10-13)
Audi S4 (12-14)
Audi S5 (13-14)
Audi TT RS (2018-)
Cadillac ATS-V (16-17)
Cadillac CTS-V (06-07)
Chevrolet Camaro SS (98-02)

Show 49 more lines

Honda Civic Type-R (2017-)
Saturn Sky / Convertible (07-09)"
In T3, Effective 1/1/2025, delete for following Spec Lines in their entirety:
"Audi TTS Coupe (10-11)
Cadillac ATS (2015)
Chevrolet Cobalt (05-07)
Dodge SRT-4 (03-05)
Ford Fiesta ST (2014-)
Hyundai Genesis Coupe (2010-)
Hyundai Veloster Turbo (18-21)
Mini Cooper S (2016-)
Toyota Camry (11-15)"
In T4, Effective 1/1/2025, delete for following Spec Lines in their entirety:
"Acura Integra GS-R VTEC (3 or 4 door) (94-01)
Audi A4 V-6 (96-01) / Volkswagen Passat 2.8 V6 (96-05)
Chevrolet Cobalt SS, Sport Coupe (06-10)
Chevrolet Sonic RS (2011-)
Chrysler/Dodge Neon ACR SOHC (4 door) (01-02)
Dodge Dart (14-15)
Dodge/Plymouth Neon ACR SOHC/DOHC (2/4 door) (95-99)
Fiat 500 Abarth (12-14)
Ford Focus SVT (02.5-04)
Ford Focus ZX4 ST (05-06)
Ford Focus (08-11)
Ford Mustang V-6 (01-04)
Honda Accord LX & EX (03-07)
Honda Accord LX-S/EX/EX-L (08-12)
Honda Civic Coupe Si (99-00)
Honda Civic SI (02-03)
Hyundai Elantra GLS (11-12)
Hyundai Tiburon V-6 (03-08)
Hyundai Veloster Turbo/ R-Spec (14-15)
Kia Forte Koup and Sedan LX/EX (10-13)
Kia Forte Koup and Sedan SX (10-13
Kia Forte Koup (14-15)
Mazda Protégé ES (2000)
Mazda Protégé 5 (02-03)
Mazda6 s (03-07)
Mitsubishi Eclipse GT (00-05)
Nissan Sentra SER (02-03)
Pontiac Firebird V-6 (96-02)
Scion tC (03-07)
Subaru Impreza (non-turbo) (04-06)
Toyota Celica GT (00-05)
Toyota Celica GTS/GT (00-05)
Volkswagen Golf TDI (2010)
Volkswagen Passat (12-14)
Volkswgen Passat TDI (12-14)
Volkswgen Passat 1.8T (2014-)"

T2 Spec Corvette Line Clarification.

#37441 from Joe Aquilante · Rule change · TB 25-01 (2025-01 Fastrack)

In T2 Spec Lines, Spec Corvette, change as follows:
Weight: "SC-3200, SC+-3300* See Notes Section"
Notes: "Cars must comply with all Spec Corvette rules dated 11-28-22 including fuel and tires. No tire treatment or rubber
softeners are permitted. Limited to 380 HP. Nankang NS-2R Tires conforming to Spec Corvette rules or a 295 R compound DOT
tire. Cars must conform to Spec Corvette rules dated 11/2022. Master cylinder part number GM 19418187 and Booster part
number 19418516 permitted. Limited to 380 HP. Any 200tw 315 tire permitted if used on all 4 corners or a 295 R compound DOT
tire.
Modifications to Radiator Air Shroud to increase radiator cooling efficiency is allowed. Replacement of factory air shroud with

Show 8 more lines

other material is allowed. New air shroud cannot be wider than inside of frame rails. The front bumper must remain in factory
shape – unmolested and air shroud must mount to it in factory location. Upper Radiator Support must retain factory location.
Factory air dam must remain in its factory location.
All factory suspension pick up points must be maintained. Trackspec’s rear upper coilover offset shock mount may be used, part
number C56UPRMNT.
The following "Spec Corvette +" allowances are permitted with a base weight of 3300 lbs: 1) Penske double adjustable shocks, 2)
dry sump, 3) battery relocation, 4) Quaife limited slip differential, 5) T2 4 piston 13"
front brake system, 6) coil springs other than Eibach part number 0800.225.0550."

T2 Mustang Update backdate

#37275 from Scotty B White · Rule change · TB 25-02 (2025-02 Fastrack)

In T2 Spec Lines, combine Ford Mustang GT 5.0L (15-17) and Ford Mustang GT 5.0L (2018-) and change as follows:
Delete in its entirety: "Ford Mustang GT 5.0L (15-17)"
"Ford Mustang GT 5.0L (2018-)(15-23)"
Required Restrictor: 58mm flat plate restrictor 2015-17 5.0 Gen 2 63mm FPR, 2018-23 5.0. Gen 3 60mm FPR"
Gear Ratios: "3.66, 2.43, 1.69, 1.32, 1.00, 0.65 or 4.69, 2.98, 2.14, 1.76, 1.52, 1.27, 1.00, 0.85, 0.68, 0.63 or 4.17, 2.34, 1.52, 1.14,
0.87, 0.69"
Notes: "Ford Performance Handling Kit part #M-FR3A-M8, Sway Bars in M-FR3A-M8 kit part #M5490-E or M5490-G, Rear Toe
Bearing part #M-5A460-M, Ford Performance Radiator part #M-8005-M8,Strut Tower Brace part# M-20201-M, Camber Bolts M-

Show 7 more lines

3B236-A, Solid Differential Bushings part#M-4425-M, Short Shift Kit part#M- 7210-M8, Solid Subframe Bushings part#M- 5872-
M, Dampers in Handling Pack part #M-18000-F, Ford OEM Performance Package Brembo front BBK and 380mm rotors permitted
(Ford PN M-2300-V) at no weight penalty. Alternate driveshaft is allowed. Springs up to 800#/in front and rear permitted.
Alternate metallic driveshaft permitted. Rear spring relocation to shock permitted with kit TBD. Ford Racing oil pan #M-6675-
M50BR permitted. BMR rear upper control arm camber links part #UTCA064 permitted. Track/Performance Package parts
permitted. Mustang S550 2015-17 5.0 Gen2 and 2018-23 5.0. Gen3 reduce weight by 100Lb when using 4 piston stock or
Brembo brakes with 355mm rotors."

Applies to Ford Mustang on this page: Scotty B White

T2 BOP Adjustment for 2016 - Camaro SS/1LE

#37434 from Kurt Rezzetano · Rule change · TB 25-02 (2025-02 Fastrack)

In T2 Spec Lines, Chevrolet Camaro, 1LE (2016-), change as follows:
"Chevrolet Camaro, 1LE (20 16-25)"
Required Restrictor: "58mm 62mm FPR"
Min Weight: "3500 3600"

T2 BMW M235iR TCS CHANGE REQUEST

#37470 from Werner Kordas · Rule change · TB 25-02 (2025-02 Fastrack)

In T2 Spec Lines, BMW M235iR (-2016), add to Notes the following:
"Oil cooler and radiator permitted according to touring rules. Silicone charge pipe permitted."

T2 Request to Classify Club Spec in Appropriate Touring Classes

#37523 from Andrew Benagh · Rule change · TB 25-02 (2025-02 Fastrack)

In T3 Spec Lines, classify Ford SCCA Club Spec Mustang (CSM) as follows:

A specification table follows in the original; it is not shown here.

Cal Club 2025 → Cal Club 2026 2025-02-22 to 2026-02-21

T2 T2 BOP

#37312 from Touring Committee · Rule change · TB 25-01 (2025-01 Fastrack)

In T2 Spec Lines, BMW M2 CS Cup 2020-, change Notes as follows:
"Effective 3/1/2025 It is mandatory to run the “Purple” power stick part #8324089"Red" power stick part #8324085."
In T2 Spec Lines, Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04), change Required Restrictor as follows:
"Effective 3/1/2025 59mm 58mm"

Applies to Chevrolet Corvette on this page: Josh Carroll, David Holmes, Patrick Howe, Evan Gold, Greg Nester, Michael Cheney, Luis Martinez

T2 Please class the Darkhorse R in T2

#37295 from Touring Committee · Rule change · TB 25-04 (2025-04 Fastrack)

In T2 Spec Lines, classify the Ford Mustang Challenge Darkehorse R.

A specification table follows in the original; it is not shown here.

T2 T2 350Z Spec Line Cleanup

#37603 from Ben Slechta · Rule change · TB 25-04 (2025-04 Fastrack)

In T2 Spec Lines, Nissan 350Z Track/ Touring/ Standard/ Nismo Spec Z (03-08), change Notes as follows:
"Nissan Motorsports: Shock Front left P/N E6110-SZ350 & Front right E6111-SZ350 & rear E6210-SZ350, Springs front P/N
54010-SZ350 & rear 55020-SZ350, F&R 5600S-SZ350, Front roll bar #54611-SZ350, Rear roll bar #562300-SZ350, Bushings P/N
(54541, 54560, 55045, 55148, 55149, 55152, 55153, 55158, 56218) - RRZ30 allowed. Nismo flywheel permitted. SPC Control
Arms 72125 and 72123 are allowed. Aftermarket flywheel permitted at minimum 14lbs. Aftermarket headers permitted, cold air
intake permitted. Aftermarket big brake kit 4 piston front permitted up to 355x32 SPL pro V3 front upper camber caster control
arms for the 350z part# SPLFUAZ33 permitted. SPL rear toe links part# SPL RTA Z33 permitted. Stillen part #400338 permitted.
44011-RC350 rear caliper kit permitted, 43206-SZ350 Right rotor permitted, 43207-SZ350 Left rotor permitted. Must conform to

Show 7 more lines

all SpecZ 2018 Edition rules. No other touring allowances beyond 2018 SpecZ edition rules or allowances listed
here. Track/NISMO/S/R-Tune OEM aero options permitted, KW Motorsports: F&R 5600S-SZ350 permitted, Front sway bar max
37mm, Rear sway bar max 25mm, RRZ30 Oil Pump allowed, Performance alternative front upper control arms permitted,
Spherical bearings allowed, Springs up to 700 lbs./in. front/rear permitted, Aftermarket flywheel permitted at minimum 14lbs, Z1
350Z Intake Power Mod Kit permitted, Aftermarket headers permitted, Cold air intake permitted, Stillen part #400338 permitted,
Zspeed and Z1 alternative clutch slave permitted, Nissan rear diff cover #99996-35TDK or #383510C021 permitted, Nissan caliper
kit: 41001-FR350 and/or 44011-RC350 permitted."

SRF Driver Safety & Comfort

#37966 from Robey Clark · Rule change · TB 25-04 (2025-04 Fastrack)

In SRF, GCR section 9.1.8.D.1.D, add the following:
"f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

SRF Update SADEV transmission specs

#37992 from Club Racing Board · Rule change · TB 25-04 (2025-04 Fastrack)

In SRF, GCR section 9.1.8.D.2.K, change as follows:
"OR
SADEV-SRF3 6-Speed Sequential (beginning from Oct. 4, 2021 onward):
1st 12-36 3.0000 : 1
2nd 15-31 2.0667 : 1
3rd 18-28 1.5556 : 1
4th 22-28 1.2727 : 1
5th 24-26 1.0833 : 1

Show 2 more lines

6th 25-23 0.9200 : 1
Final Drive Ratio: 15-48 3.20"

T2 C6 T-2 Corvette 6 Liter Engine Restrictor

#37490 from Joe Aquilante · Rule change · TB 25-05 (2025-05 Fastrack)

In T2 Spec Lines, Chevrolet Corvette C6 Coupe / Grand Sport (05-13), Required Restrictor, change as follows:
LS2: "63mm 67mm FPR"

T2 370Z Mid link Replacement for True Coil Overs and OEM Wheel Size

#38014 from Zachary Hayward · Rule change · TB 25-05 (2025-05 Fastrack)

In T2 Spec Lines, Nissan 370Z (09-17) / 370Z NISMO Edition (09-17), change as follows:
Max Wheel Size: "19 x 10 10.5"
Notes: "5300S-SS370 T-2 spring kit allowed; 54600-SS370 Sway Bars allowed 35mm (f). 29mm (r) Sports Package is allowed.
Springs up to 1000 lbs/in front and rear allowed. 54010- SZ350 (F) and 55020-SZ350 (R) allowed. Cold Air Intake allowed.
Performance Alternative Header permitted. Rear spring relocation permitted to allow coil over shocks. SPL suspension kit
permitted that includes: rear camber arms #SPL RLL Z34 or Nismo 551A0-RLLRZ, , SPL rear traction arms #SPL RTR Z34, or Nismo
55110-RTRRZ SPL front camber arms #SPL FUA Z34,or 54525-FUAZ4 SPL rear mid link #SPL RML Z34 or Nismo 551B0-RMLZ4. SPL
Part# SPL RTA Z34D or NISMO Part# 551B0-RTARZ permitted. Zspeed and Z1 alternative clutch slave permitted. The following

Show 1 more lines

STOPTECH parts are allowed with a 50 Lb penalty: #83.488.6800.51 front, 83.657.0057.51 rear."

T2 T2 Cadillac tire

#38210 from Touring Committee · Rule change · TB 25-05 (2025-05 Fastrack)

In T2 Spec Lines, CT4-V Blackwing (2022-), change Tire Size Max as follows:
“295 315”

T2 Incorrect Touring Heading

#38451 from Terry Hanushek · Rule change · TB 25-08 (2025-08 Fastrack)

In T2-T4 Spec Lines, change Table Header as follows:
"T2 ET"

T2 Clarifications needed to BMW M2 CS cup line

#38536 from Joe Aquilante · Rule change · TB 25-08 (2025-08 Fastrack)

The BMW M2 CS Clubsport is classed in T1, not T2. Please visit the following web address for vehicle details about the car's base
allowances-
https://www.bmwusa.com/motorsport/bmw-m2-
cs.html#:~:text=The%20BMW%20M2%20CS%20Racing%20models%20are%20powered%20by%20a,M2%20CS%20Racing%20Rec
ommended%20Mileage.
In T2 Spec Lines, BMW M2 CS Cup 2020, change as follows:
Model: "BMW M2 CS Cup 2020-2021"
Notes: "DOT approved tires required. All other components must be as homologated from BMW Motorsports. No other changes

Show 5 more lines

or Touring rule allowances permitted unless noted below. It is permitted to remove door glass and mechanism. It is mandatory
to run the “Purple” power stick part #8324089. Effective 3/1/2025 5 It is mandatory to run the “Red” power stick part #8324085.
BMW exhaust part # 18302459928 allowed. Hot country package allowed including part numbers: (aKMK LH 17 10 8342846 1,
aKMK RH 17 10 8328139 1, 17 10 8328135 1, 17 10 8328136 1, 17 10 8328137 1, 17 10 8328138 1, ISO7380-2 M5X14 10.9 ZNSW
17 10 8436008 2, 17 10 8417424 1.) Hood vents conforming to 9.1.9.2.D.8.a.7 are permitted."

T2 Fix brake allowance supersessions.

#38554 from Touring Committee · Rule change · TB 25-08 (2025-08 Fastrack)

In T2 Spec Lines, change Brakes as follows:
Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04): "(F) 325 Vented Disc (R) 305 Vented Disc May use two piece
steel rotors with aluminum hats up to 5% larger than 340/330; Any four piston calipers and brackets are permitted. Any brake
caliper pistons are allowed; may use the Wilwood SL6R brake caliper. Stock calipers and rotors only (F) 325 (R) 305"
Chevrolet Corvette C6 Coupe / Grand Sport (05-13): "(F) 325 / 340 Vented Disc (R) 305 / 330 Vented Disc or (F) 355 x 32 Vented
Disc (R) 340 x 26 Vented Disc or May use 2-pc steel rotors with alum. hats up to 5% larger than Z51 rotor. LS2 may use Grand
Sport brake package. Any brake caliper pistons allowed. May use any four piston brake caliper and brackets. Z06 brake calipers
allowed."

T2 C5 Corvette correction

#38782 from Touring Committee · Rule change · TB 25-08 (2025-08 Fastrack)

In T2 Spec Lines, Chevrolet Corvette C-5 Incl. Fxd Cpe (98-04) Z06 (hardtop) (01-04), change Restrictor Required as follows:
"LS1: 59 58mm FPR,
LS2: 63mm FPR,
LS3: 56mm FPR,
LS6: 58mm FPR"

Applies to Chevrolet Corvette on this page: Josh Carroll, David Holmes, Patrick Howe, Evan Gold, Greg Nester, Michael Cheney, Luis Martinez

SRF Add HD Oil Cooler

#38979 from Robey Clark · Rule change · TB 25-10 (2025-10 Fastrack)

In SRF, GCR section 9.1.8.D.1.V.ff, change as follows:
"SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan
permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."

T2 ND Gearset Request for T4

#39166 from Josh Smith · Rule change · TB 25-11 (2025-11 Fastrack)

In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), add to Notes the following:
"Gear kit Kit PT#- 0000-02-6100."
In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), add to Notes the following:
"Gear kit Kit PT#- 0000-02-6100."
In T3 Spec Lines, Mazda MX-5 Miata (16-18), add to Notes the following:
"Gear kit Kit PT#- 0000-02-6100."
In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, add to Notes the following:
"Gear kit Kit PT#- 0000-02-6100."

T2 ND Spec Lines Wrong PT#'s

#39170 from Josh Smith · Rule change · TB 25-11 (2025-11 Fastrack)

In T4 Spec Lines, Mazda MX5 Miata/Club/ RF (19-24), change Notes as follows:
"Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. The following item(s) must remain
stock: transmission differential unless specified below. Retractable hardtop option permitted but must be disabled from moving
action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the OEM roof silhouette, including
Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports). 29mm (f) 16mm (r) sway bars
allowed. 3rd and 4th gear may be replaced with the following parts- (0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02,
0000-02-5804-01). Suspension package permitted with a 100 lbs. weight increase that includes the following parts: front springs
#0000-04-9700-08, springs up to 500lb front and 300lb rear allowed. Mazda tower brace 0000-04-5626 allowed. Mazda header

Show 20 more lines

0000-06-5410 allowed."
In T4 Spec Lines, Mazda MX-5 Miata/Club (16-18), change Notes as follows:
"Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. Retractable hardtop option permitted
but must be disabled from moving action and positively fastened. Any OEM or aftermarket hardtop is permitted that retains the
OEM roof silhouette, including Mazda hardtop part #0000-07-5902-ND and part #0000-07-5901 (discontinued DG Motorsports).
29mm (f) 16mm (r) sway bars allowed. Up to 500lb front and 300lb rear springs allowed. Mazda Motorsports Header part
#0000-06-5410 allowed. Mazda tower brace 0000-04-5626 allowed. 3rd and 4th gear may be replaced with the following parts-
(0000-02-5803-02, 0000-02-5803-01, 0000-02-5804-02, 0000-02-5."
In T3 Spec Lines, Mazda MX-5 Miata (16-18), change Notes as follows:
"Factory bolt-in roll bar/ cross member may be removed to facilitate roll cage installation. Header permitted. Cold air intake
permitted. Front strut brace permitted. Front and rear sway bars permitted up to 35mm, Springs 800 front and 800 Rear max
permitted. Any OEM or aftermarket hardtop permitted that retains the OEM roof silhouette including Mazda hardtop part
#0000-07-5902- ND and part #0000-07-5901 (discontinued DG Motorsports top). If a hardtop is used, latches shall be replaced
with positive fasteners. Retractable hardtop option permitted but must be disabled from moving action and positively fastened.
In T3 Spec Lines, Mazda MX-5 Global Cup Miata (2016-2021) ND1, ND, change Notes as follows:
"Shoulder harness installation must conform to FIA mounting specifications that are approved for this vehicle per section 6.2 FIA
article 253, safety equipment. Must meet all ND2 MX-5 Global Cup rules. Any OEM or aftermarket hardtop is permitted that
retains the OEM roof silhouette, including Mazda hardtop Mazda hardtop part #0000-07-5902-ND and #0000-07-5902-ND part
#0000- 07-5901 (discontinued DG Motorsports). If a hardtop is used, latches shall be replaced with positive fasteners. OBD2
requirement does not apply. Ballast box may be removed. ND2s with sequential gearbox allowed +100 lbs.

T2 Touring 2 Post-Runoffs BOP Adjustments and Changes

#39274 from Touring Committee · Rule change · TB 25-11 (2025-11 Fastrack)

In T2 Spec Lines, Spec Corvette, change as follows:
Weight: "SC3200 SC+- 3300 See notes section"
Notes: "The following “Spec Corvette +” allowances are permitted with a base weight of 3300 lbs:"
In T2 Spec Lines, Ford Mustang GT 5.0L (11-14), change Restrictor as follows:
"60mm 62mm flat plate restrictor"
In T2 Spec Lines, Ford Mustang GT 5.0L (2015-23), change Tire Size as follows:
"295 315"
In T2 Spec Lines, Porsche 911 / 996 (98-05), change Weight as follows:

Show 11 more lines

"3600: 3150 3050
3400: 3000"
In T2 Spec Lines, Porsche Carrera S 997.2 (06-08), change as follows:
Restrictor: "60mm 65mm FPR"
Weight: "3225 3175"
In T2 Spec Lines, Porsche 911 / Carrera S 997.2 (09-12), change as follows:
Restrictor: "60mm 65mm FPR"
Weight: "3300 3250
In T2 Spec Lines, Porsche 911 / 997.2 GTS (09-12), change as follows:
Restrictor: "60mm 65mm FPR"
Weight: "3400 3350"

Applies to Ford Mustang on this page: Scotty B White

T2 Adjust rev limit on Spec Corvette in T2

#39282 from Touring Committee · Rule change · TB 25-11 (2025-11 Fastrack)

In T2 Spec Lines, Spec Corvette, add to Notes the following:
"7) up to 7100 rpm Rev limit."

T2 Help the 2011-2014 s197Mustang GT and Boss302 Less Restriction

#38523 from Joe Aquilante · Rule change · TB 25-12 (2025-12 Fastrack)

In T2 Spec Lines, Ford Mustang Boss 302 (12-13), change Restrictor as follows:
"56mm 63mm flat plate restrictor"
In T2 Spec Lines, Ford Mustang GT 5.0L (11-14), change Restrictor as follows:
"60mm 65mm flat plate restrictor"

Applies to Ford Mustang on this page: Scotty B White

T2 Improving Competitiveness of Gen 5 Camaro SS

#39021 from Van Hunter · Rule change · TB 25-12 (2025-12 Fastrack)

In T2 Spec Lines, Chevrolet Camaro SS/1LE (10-15), change Weight as follows:
"3625 3575"

T2 Adjust T2 Darkhorse R

#39346 from Andrew Aquilante · Rule change · TB 25-12 (2025-12 Fastrack)

In T2 Spec Lines, Ford Mustang Challenge, change as follows:
Car: "Ford Mustang Challenge Darkehorse/Cup Dark Horse R (2024-)
Displacement: "92.220 x 92.7 / 4957 93.0mm x 92.7mm 5038cc"
Weight: "3650 3775 3825"
Restrictor: "2 x 55 mm"
Tires: "295 315"
Notes: "Safety and camera equipment is unrestricted."
"**This car spec line is not eligible for the Runoffs until it has competed in 3 Super Tour events.**

Applies to Ford Mustang on this page: Scotty B White

T2 Alternate Placement of Fuse Panel and Electronics Request

#39370 from Aaron Stehly · Rule change · TB 26-01 (2026-01 Fastrack)

In GCR, Section 9.1.9.2.D.9.d, add the following:
"8. Under-dash electronics including computers, modules and fuse boxes may be relocated so they can be easily accessed after
roll cage installation."

T2 Rebalance Blackwing Cadillac T2 for 2026

#39426 from John Heinricy · Rule change · TB 26-01 (2026-01 Fastrack)

In T2 Spec Lines, Cadillac CT4-V Blackwing (2022-), change Weight as follows:
"3800 3750"

T2 C6 LS2 Corvette Parity Request

#39472 from Brian LaCroix · Rule change · TB 26-01 (2026-01 Fastrack)

In T2 Spec Lines, Chevrolet Corvette C6 Coupe / Grand Sport (05-13), change Restrictor as follows:
"LS2: 67mm 80mm FPR LS3: 56mm FPR"

T2 T2 Tire Sizing

#39490 from Scotty B White · Rule change · TB 26-01 (2026-01 Fastrack)

In T2 Spec Lines, Dodge Viper SRT10 incl. coupe (03-06), change Weight as follows:
"3675 3650"

T2 Rear Spoiler for Mustang GT S550 (15-23)

#39499 from Andrew Aquilante · Rule change · TB 26-01 (2026-01 Fastrack)

In T2 Spec Lines, Ford Mustang GT 5.0L (2015-2023), add to Notes the following:
"Ford Track/Performance Package parts permitted. Performance pack aero parts #M-16600-FP and #M-16601-MPP permitted."

Applies to Ford Mustang on this page: Scotty B White

T2 Clarify T4 Brake Rotor Allowance

#39503 from David Mead · Rule change · TB 26-01 (2026-01 Fastrack)

In GCR, Section 9.1.9.2.D.6.a.6., change as follows:
"In T2-Performance alternative rotors, including 2 piece rotors are permitted. Rotors must be within 5% of OE diameter or a
maximum diameter of 360mm.
In T3- Performance alternative rotors, including 2 piece rotors are permitted with a maximum diameter of 360mm.
T4- Performance alternative 1-piece rotors are permitted but rotors must meet the sizes listed in the spec line. Spec lines
showing alternate brake kits are also permitted to use 1-piece performance alternative rotors of the same size."

T2 Request to Add 2014-2017 435i to T2

#38991 from Jimmy Cabrera · Rule change · TB 26-02 (2026-02 Fastrack)

In T2 Spec Lines, classify as follows BMW 435I (2014-2017):

A specification table follows in the original; it is not shown here.

T2 Consideration for Nissan Z & NISMO Z to Touring 2 Class

#39296 from Greg Nelson · Rule change · TB 26-02 (2026-02 Fastrack)

In T2 Spec Lines, classify Nissan Z incl. Nismo as follows:

A specification table follows in the original; it is not shown here.

T2 Allow Alt Bushing Material in Toe Links

#39607 from David Mead · Rule change · TB 26-02 (2026-02 Fastrack)

In GCR, Section 9.1.9.D.5.a.1., change as follows:
"T2-T4: A maximum of 3.5 degrees of negative camber is allowed on front and rear suspensions. Spec line part(s) may not be
modified to increase caster and camber. Strut suspensions may adjust camber and caster by the use of eccentric bushings,
eccentric bolts (crash bolts) at the strut-to-spindle, and/or by use of slotted adjustment plates at the top of the strut mounting
plate. If upper strut slotted adjustment plates are used, they shall be located on existing chassis structure, utilizing the
unmodified manufacturer’s original bolt holes and may not serve as reinforcement for that structure. Slotted adjustment plates
(strut camber plates) may incorporate a single spherical bearing (spherical bushing) and a ball thrust bearing per strut tower. On
other forms of suspension, camber and caster adjustment may be achieved by the use of shims and/or eccentric

Show 4 more lines

bushings. Adjustable toe links with spherical bearings are permitted and may serve no purpose other than adjusting toe
angle. Adjustable toe links are permitted. They are allowed to have performance alternative bushings and spherical bearings.
They may serve no purpose other than adjusting toe angle. Spherical bearings/bushings are not permitted in T2-T4 except for the
specific examples listed in the class rules or vehicle spec line."

T2 Request for Classification of MG6 TCR in T2-TCR Class

#39702 from Vito Jin · Rule change · TB 26-02 (2026-02 Fastrack)

In T2-TCR Spec Lines, classify Link & Co 03 TCR (2019-2025) and MG6 TCR (2019-2022) as follows:
T2-TCR Transmission Power Level Weight(lbs) Notes
Link & Co 03
TCR (2019-
2025)
SEQ 90% 3000 DOT approved tires with maximum section width
of 275. T2-TCR splitter and valance must comply
with 9.1.4.D.3.f. T2-TCR chassis ride height must

Show 7 more lines

comply with 9.1.4.1.A.1
MG6 TCR
(2019-2022)
SEQ 90% 3000 DOT approved tires with maximum section width
of 275. T2-TCR splitter and valance must comply
with 9.1.4.D.3.f. T2-TCR chassis ride height must
comply with 9.1.4.1.A.1

What the rules allowed changed as listed; this does not say what any particular car ran.