AS + FM + SRF + STU at Michelin Raceway Road Atlanta

In STU Spec lines, classify Mazda BP5A as follows:
STU Maximum Displacement (cc's) Minimum Weight Notes
Mazda BP5A 1839 Chart May use engine in its entirety or specific
components from the engine.

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Front – Hoosier P/N 46100 1 P185/65R13 W2"

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5" with driver as raced when P185/60R13 (H20 or W2) tires are used."

In STU Spec Lines, Toyota GR Cup (2022-), classify as follows:

A specification table follows in the original; it is not shown here.

In AS, GCR Section 9.1.6.F.2., change as follows:
"GM Performance parts CT400 P/N-1937 → 0604 or 1937 → 0604 engine assembly for GM produced vehicles."

In AS Spec Lines, Ford Mustang GT 5.0l (15-17) Restricted Preparation, change Notes as follows:
"Max. Wheel Size: Dia.18.0 19.0 inches."

In AS SPEC Lines, Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2
valves/cylinder, change Notes as follows:
"SPC-66045 Alternate front upper control arms are permitted."

In AS SPEC Lines, Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2
valves/cylinder, change Notes as follows:
"Stock brakes or alternate Dodge brakes (Part numbers: front caliper (0517 → 5106 (R) and 0517 → 5107 (L); rear caliper (R1542564 (R)
and R1542565 (L))) may be used with the brake rotor sizes listed in this specification line. Alternate brackets may be used to
facilitate updated/backdated components."

In SRF, GCR section 9.1.8.D.1.V.j, change as follows:
"Radiator - Enterprises new style P/N 480465 (requires baffle P/N 480464) or P/N 480466 can be used. P/N 480466, may can be
replaced with Automotive P/N 1R698, CU698 or equivalent OEM manufacturer justified by one cross-reference chart equivalent,
as long as the size, shape, and material are the same as the original P/N. The capacity, core thickness, etc., cannot be changed
even if allowed under the above. The competitor is responsible for providing this documentation of the cross-reference P/N."

In SRF, GCR section 9.1.8.D.1.W.l, change as follows:
"A Super Bright LEDs Inc. rain / brake light comprised of a single standard trailer oval lamp, 2-1/4 inches x 6-1/2 inches, with
incandescent or LED illumination, P/N PT-STRB-R24, is required in the original roll hoop mounting location. This rule supersedes
GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No changes may be made to the original 3-pin connector on the
wiring harness. The secondary filament of the brake light assembly shall must be connected to a switch enabling its use as a rain
light."

In SRF, GCR section 9.1.8.D.1.W.l, change as follows:
"A Super Bright LEDs Inc. P/N PT-STRB-R24 (SCCA Enterprises P/N 180427A) rain / brake light, P/N PT-STRB-R24, is required in the
original roll hoop mounting location. This rule supersedes GCR section 9.3.32.B.2 effective 1/1/2024 through 12/31/2024. No
changes may be made to the original 3-pin connector on the wiring harness. An SCCA Enterprises P/N 1190503 Strobing Brake
Light Pigtail is required. The secondary filament of the brake light assembly must be connected to a switch enabling its use as
a strobing rain light. A Strobing Brake Light Kit P/N 1168003 is available, which includes the brake light and pigtail."

In SRF, GCR section 9.1.8.D.1.H, add the following:
"NO MODIFICATIONS ALLOWED. Front brake ducts are required, attached to the openings in the lower radiator baffles, any
flexible 4" duct material allowed, installed length minimum 12" maximum 36" in length. Must be securely fastened, Bracket Part
# P/N 800368 can be used. Shall Must serve no other purpose. An extension may be welded to the side of the throttle pedal to
improve heel-and-toe braking. Master cylinder casting / location must be used as delivered on P/N 180110 Pedal Mounting
support. Aeroquip style -3 braided stainless flex lines only, must attach to all brake components without modification. Brake pad
"anti-rattle" clips must be removed."
In SRF, GCR section 9.1.8.D.1.V, add the following:
"ii. Rear SADEV shift cable aluminum two-piece style clamp may be used. The P/N WM302007A clamp must serve no other
purpose."
In SRF, GCR section 9.1.8.D.1.X.k, add the following:
"Negative camber shall must not exceed 5.0 degrees absolute maximum front and rear."
In SRF, GCR section 9.1.8.D.1.AA.b, add the following:
"2. Height of the radiator opening vertical surface 3 1/2“ +/- 1/2"."
P2 Engine Table B.1
2008 and older Stock
Suzuki, Yamaha,
Honda, BMW
38.5mm
P2 Engine Table B.2 Not required
P2 Engine Table B.3 38.5mm
Modified
Engine
950 lbs.
1005cc max
P2 Engine Table B.1
2008 and older 37mm
P2 Engine Table B.2 Not required
P2 Engine Table B.3 39mm
Stock Engine
1050 lbs.

In GCR, Section 9.1.4.M.16., change as follows:
"Power steering may be modified in any of the following ways:
a. disconnected , pump, belt, pulley, and hoses may be removed. Hoses may also be looped. Steering rack or box may be
modified internally to work without pump.
b. an OEM manual steering rack for that model may be fitted
c. an electric power steering pump may be fitted
d. an OEM electric-assisted steering system may be used or any column mounted electric steering assist may be used
e. an OEM hydraulic-assisted steering system may be used"

In AS Spec Lines, classify Chevrolet Camaro, Pontiac Firebird (70-81) Full Prep as follows:
AS Wheelbase Gear Ratios
Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs) Notes:

A specification table follows in the original; it is not shown here.

In AS Spec Lines, add to Notes as follows:
Cadillac CTS-V (04-07): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken
from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.”
Chevrolet/Pontiac Camaro & Firebird (93-02): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell.”
Chevrolet/Pontiac Camaro & Firebird (93-02): “Fuel cells must be located within 24 inches of the standard tank. The 24
inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell.”
Chevrolet Camaro SS (V8) (10-15): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell.”
Chevrolet Camaro (10-15): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is
taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”
Dodge Challenger (08-20): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is
taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”
Ford Mustang GT (05-14): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is
taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”
Ford Mustang Coupe GT (05-14): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell.”
Ford Mustang GT 5.0l (15-17): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement
is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”
Ford Mustang GT (05-14): “Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is
taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a
safety fuel cell.”

In AS Spec Lines, classify Chevrolet Camaro (16-) Full Prep as follows:
AS
Wheelbase Gear Ratios
Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs) Notes:
Chevrolet
Camaro (16-)
Full Prep
110.6 3.42, 2.28,

A specification table follows in the original; it is not shown here.

In STU Spec Lines, Mini Cooper S SC with Minimum Weight 1900 and 2100, add to Notes:
"Alternate LEAP OMICRON hood scoop part # LEP-OMICRON3 is permitted."

In STU Spec Lines, BMW S54 B32 OEM, add to Notes as follows:
"Dry Sump oiling system permitted."

In AS Spec Lines, classify Ford Mustang GT (05-14) with Restricted prep Engine as follows:
AS
Wheelbase Gear Ratios Std.

A specification table follows in the original; it is not shown here.

In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (93-02), add to Notes the following:
"For the LS1connecting rods Callies p/n CSC6100DS6A2AH, Scat rods p/n 2-1CR6100-944, GM performance rods p/n 12649190."
In AS Spec Lines, Pontiac GTO (04-06), add to Notes the following:
"For the LS1connecting rods Callies p/n CSC6100DS6A2AH, Scat rods p/n 2-1CR6100-944, GM performance rods p/n 12649190."

In AS Spec Lines, Cadillac CTS-V (04-07), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Chevrolet Camaro SS (V8) (10-15), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Dodge Challenger (08-20), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Ford Mustang GT 5.0l (15-17), add to Notes the following:
"11" wide wheels can be used until 3/1/25."
In AS Spec Lines, Pontiac GTO (04-06), add to Notes the following:
"11" wide wheels can be used until 3/1/25."

In AS Spec Lines, classify Chevrolet Camaro 1LE (2016-) as follows:
AS Wheelbase Gear Ratios Std. (or Alt.)
Brakes
(Max)
(in/mm)
Weight (lbs.) Notes:
Chevrolet
Camaro, 1LE
(2016-)
110.6 2.66,1.78,1.30,0.74,.5 (F)

A specification table follows in the original; it is not shown here.

In AS Spec Lines, classify Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V-8 LS1 (Aluminum Block, Aluminum Heads) 2 valves
per cylinder, as follows:
AS Wheelbase Gear Ratios Std.

A specification table follows in the original; it is not shown here.

In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (82-92), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Chevrolet/Pontiac Camaro & Firebird (93-02), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Chevrolet Camaro (10-15), add to Notes the following:
"Flo Tek Head part #102-500 are permitted."
In AS Spec Lines, Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86), add to Notes the following:
"Flo Tek Part # 203-500 are permitted."
In AS Spec Lines, Ford Mustang Including Cobra 94-04, add to Notes the following:
"Flo Tek Part # 203-500 are permitted."
In AS Spec Lines, Ford Mustang GT (05-14), add to Notes the following:
"Flo Tek Part # 203-500 are permitted."

AS Spec Lines, classify Ford Mustang GT 5.0L (2018-) as follows:
AS Wheelbase Gear Ratios

A specification table follows in the original; it is not shown here.

In GCR, Section 9.1.4.1.H.3 - Inlet Restrictor (mm) Minimum Weight (lbs) table, change as follows:
"RWD cars must reduce restrictor 1 mm from this table"

In SRF, GCR section 9.1.8.D.1.X.f, change as follows:
"Wet:
Front – Hoosier P/N 46100 P185/60R13 H20 or W2
Rear – Hoosier P/N 46105 P205/60R13 H20 or W2
Ground clearance is 2.5” with driver as raced when P185/60R13 (H20 or W2) tires are used.
OR
Front – Hoosier P/N 46101 P185/65R13 W2
Rear – Hoosier P/N 46105 P205/60R13 W2
1. It is forbidden to regroove tires.
2. The use of tire warmers or cooling methods other than natural air convection or conduction is prohibited. The penalty for
violation will be the loss of qualifying times and/or the disqualification of race results.
3. Hoosier SRF/SRF3 Decal Placement:
Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose to
the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the
rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including
SCCA Enterprises."

In FE, GCR section 9.1.1.I.2.U.b.3, change as follows:
"Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure."
In SRF, GCR section 9.1.8.D.1.U.b.3, change as follows:
"Protest Fee: Regional -$25.00, National -$50.00. See GCR section 8.3.1.D for fees and payment procedure. Item 1 will be done by
the CSR or other shop that is equipped for this type of work and will be paid directly."

In SRF, GCR section 9.1.8.D.1.X.f.3, change as follows:
"Four (4) "Hoosier" decals are required in the following locations: Two (2) 11" X 3" decals on the vertical plane of the front nose
to the outside of the cooling opening on each side and two (2) 18" X 5" decals, one on each side of the engine cover or above the
rear wheel openings on the vertical plane. Hoosier decals are available, free of charge, from all Hoosier tire distributors including
SCCA Enterprises Per Hoosier's contingency program, three (3) decals are required to qualify for contingency awards. One (1)
decal must be located on each side of the car and one (1) decal must be visible on the front."

In AS Spec Lines, Ford Mustang GT (05-14) with Restricted Prep Engine, add to Notes as follows:
"Alternate transmission Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68.”
In AS Spec Lines, Ford Mustang GT 5.0L (2018-), add to Notes as follows:
"Alternate transmission Ratios 3.24, 2.10, 1.42, 1.00, 0.81, .062."

In SRF, GCR section 9.1.8.D.2.H.23, change as follows:
"Air Filter: P/N WM301020 or K&N RC-9160"

In SRF, GCR section 9.1.8.D.1.X.g, change as follows:
"Brakes: Hawk Blue 9012 pads P/N 801993 must be used. Wilwood vented rotor P/N 800065 shall must be used as delivered with
no machining of any kind. Minimum thickness 12.20mm (0.481”) 13.25mm (0.522”)."

In SRF, GCR section 9.1.8.D.2.B, change as follows:
"Mandatory identification: "SRF3" near the side car numbers. "Hoosier" logo (4) on both sides front lower outer corners of the
nose and each side of the tail. Three (3) "Hoosier" logos, one (1) on each side of the car and one (1) on the center front of the car."

In STU Spec Lines, Mini Cooper S SC, add to notes:
1900: "Stock supercharger pulley. 2.565 diameter."
2100: "JCW Pulley permitted. May run a 2.285 diameter pulley."

In GCR, Section 9.1.4.M.18., change as follows:
"18. Allow alternate front wheel front hubs, Mazda Motorsports Development Part #0000-04-5HUB-S1, for the 90-05 Mazda
Miata: Mazda Motorsports Development Part #0000-04-5HUB-S1."

"Turbo inlet restrictors designed per GCR Appendix F Technical Glossary definition of “Turbo Inlet Restrictor” may be required;
see table 9.1.4.1.H.h.2 3. Swapping of turbochargers between engine makes and models is prohibited. Supercharged cars may be
approved on a case-by-case basis; twin turbo engines are allowed on a case-by-case basis only. Contact the Road Racing
Technical Office for details. Twin turbo engines may be converted to single turbo using one of the allowed alternate turbos (see
9.1.4.1.H.3 2). Aftermarket turbocharger and supercharger kits will be allowed on a case-by-case basis.

In AS Spec Lines, add to Notes as follows:
Ford mustang (GT 05-14): "Gen 1- 67mm Gen 2-64mm"
Ford mustang (GT 05-14): "Gen 1- 67mm"
Ford mustang (GT 15-17): "Gen 1- 67mm"
Ford mustang (GT 94-04): "Gen 1- 67mm Gen 2-64mm"
Ford mustang cobra & Cobra R Mercury Capri (79-93) (79-86): "Gen 1- 67mm Gen 2-64mm"

In STU Spec Lines, Table B: Alternate Vehicle and Engine Requirements, delete Audi/VW 1.8 Turbo in its entirety.
In STU Spec Lines, Table B: Alternate Vehicle and Engine Requirements, Porsche 944 w/Max Displacement 1800, change as
follows:
Weight: "3050 Chart"
Notes: "VW/Audi 1.8L 35mm turbo engine permittedinlet restrictor required."

In AS Spec Lines, Ford Mustang Coupe GT (05-14) Restricted Prep., change Notes as follows:
"The 4.6L engine assembly has a weight reduction of 300 lbs. 5.0L/6spd engine/trans: track pack front and rear spoiler allowed."
In AS Spec Lines, Ford Mustang Coupe GT (05-14) with Restricted Prep. engine, change Notes as follows:
"Max. Wheel Size: Dia.18.0 inches. Stock brakes or alternate Ford 14” Brembo Brake (Ford Racing Kit #M-2300-S) and full prep
brake package may be used. Either engine may be used. 1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l
Coyote 15-17 61mm FPR Cold Air Intake allowed Charge Motion Control Valves can be blocked off and removed for firewall
clearance Allow Cold Air Intake Tremec Magnum transmission may be used P/N- TUKT16901. Full Prep Transmissions rule
package may also be used. Max compression ratio, 11.2:1 track pack front and rear spoiler allowed. Alternate transmission
Ratios 3.66, 2.43, 1.69, 1.32, 1.00, .68."
In AS Spec Lines, Ford Mustang GT 5.0l (15-17) Restricted Preparation, change Notes as follows:
"Max. Wheel Size: Dia. 18.0 inches. Stock brakes or alternate Ford Brembo Brake caliper (Ford Racing Kit #M-2300-S) may be
used. 61mm flat plate restrictor required. Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation
of a safety fuel cell. 11” wide wheels can be used until 3/1/25. Performance pack front and rear spoiler, body kit allowed."
In AS Spec Lines, Ford Mustang GT 5.0L (2018-), change Notes as follows:
"Package Brembo front BBK and 380mm rotors permitted (Ford PN M-2300-V) at no weight penalty. 60mm flat plate restrictor
required. 2014 Mustang GT exhaust manifolds permitted. Ford Racing oil pan #M-6675-M50BR permitted. Alternate
transmission Ratios 3.24, 2.10, 1.42, 1.00, 0.81, .062. Performance pack front and rear spoiler, body kit allowed."

In AS Spec Lines, change Gear Ratios as follows:
Cadillac CTS-V (04-07):
"2.97, 2.07, 1.43,1.00, 0.84,0.56 or 3.01, 2.07, 1.43, 1.0, .84, .57 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33, 1.00"
Chevrolet Camaro, Pontiac Firebird (70-81), Full Prep:
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61, or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00"
Chevrolet Camaro, Pontiac Firebird (70-81), Restricted Prep.:
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61, or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00"
Chevrolet/Pontiac Camaro & Firebird (82-92) Full Prep:
"3.42, 2.28, 1.45, 1.00 or 2.95, 1.94, 1.34, 1.00, 0.73 or 3.35, 1.93, 1.29, 1.00, 0.61 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33,
1.00"
Chevrolet/Pontiac Camaro & Firebird (93-02) Full Prep:
"3.42, 2.28, 1.45,1.00 or 2.95, 1.94,1.34, 1.00,0.73or 3.35, 1.93,1.29, 1.00,0. 61 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00,
0.68 or 2.20,1.64,1.28,1.00 or 2.87,1.89,1.28,1.00,.81"
Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted prep:
"2.97, 2.07, 1.43, 1.00, 0.80, 0.62 or 3.36, 2.07, 1.35, 1.00, .80, .62 or 2.66, 1.78, 1.30, 1.00, 0.74, 0.50 or 2.88, 1.91, 1.33, 1.00 or
2.20, 1.64,1.28,1.00"
Chevrolet Camaro SS (V8) (10-15) Restricted Prep:
"3.01, 2.07, 1.43, 1.0, .84, .57 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Chevrolet Camaro (10-15) Full Prep:
"3.42, 2.28, 1.45,1.00 or 2.95, 1.94,1.34, 1.00, 0.73or 3.35, 1.93,1.29, 1.00,0. 61 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00,
0.68 or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00,.81"
Chevrolet Camaro (16-) Full Prep:
"3.42, 2.28, 1.45,1.00 or 2.95, 1.94,1.34, 1.00, 0.73or 3.35, 1.93,1.29, 1.00,0. 61 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00,
0.68 or 2.20, 1.64,1.28,1.00 or 2.87,1.89,1.28,1.00,.81"
Chevrolet Camaro, 1LE (16-):
"2.66,1.78,1.30, 0.74,.50 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Dodge Challenger (08-20) Restricted Preparation 5.7L, 6.1L, or 6.4L V8 (Iron block, Aluminum heads), 2 valves/cylinder:
"2.97, 2.1, 1.46, 1.00, 0.74, 0.50 or 2.26, 1.58, 1.19, 1.00, 0.77, 0.63 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86) Full Prep:
"3.07, 1.72, 1.00, 0.70 or 2.95, 1.94, 1.34, 1.00, 0.63 or 3.35, 1.99, 1.33, 1.00, 0.68 or 2.87 1.89 1.28 1.00 0.81"
Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86) with Restricted Prep Engine:
"2.95, 1.94, 1.34,1.00, 0.63 or 3.35,1.99,1.33, 1.00, 0.69 or 2.88, 1.91, 1.33, 1.00 or 3.27,1.98, 1.34, 1.00, 0.68, 3.66, 2.43, 1.69,
1.32, 1.00, .68. or 2.87,1.89,1.28,1.00,.81"
Ford Mustang Including Cobra 94-04 Full Prep:
"3.07, 1.72, 1.00, 0.70 or 2.95, 1.94, 1.34, 1.00, 0.63 or 3.35, 1.99, 1.33, 1.00, 0.68 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34,
1.00, 0.68 or 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 or 2.20, 1.64,1.28,1.00 or 2.87 1.89 1.28 1.00 0.81"
Ford Mustang Cobra and GT 94-95 (Restricted Prep):
"3.35, 1.99, 1.33, 1.00, 0.68 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang including Cobra 96-04 (Restricted Prep) 4.6L two and four valve motor:
"3.35, 1.99, 1.33, 1.00, 0.68 or 3.27, 1.98, 1.34, 1.00, 0.67 or 3.37, 1.99, 1.33, 1.00, 0.68 or 3.38, 2.00, 1.32, 1.00, 0.68 or 2.88,
1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang GT (05-14) Full Prep:
"3.38, 2.00, 1.32, 1.00, 0.68 or 3.66, 2.43, 1.69,1.32, 1.00, 0.65 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang GT 5.0l (15-17) Restricted Preparation:
"3.66, 2.43, 1.69,1.32, 1.00, .65 or 4.69, 2.98,2.14, 1.76,1.52, 1.27,1.00, 0.85, 0.68, 0.63, or 3.24, 2.10, 1.42, 1.00, 0.81, .062. or
2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Ford Mustang GT 5.0L (2018-) Restricted Preparation:
"2.97, 2.07, 1.43, 1.00, 0.84, 0.57 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"
Pontiac GTO (04-06) Restricted Prep.
"2.97, 2.07, 1.43, 1.00, 0.84, 0.57 or 2.88, 1.91, 1.33, 1.00 or 2.20, 1.64,1.28,1.00"

In AS SPEC LINES, Cadillac CTS-V (04-07) Restricted Prep., change Notes as follows:
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Tremec TR6060
Transmission with 3.0 1, 2.07, 1.43, 1.0, .84, .57 ratios permitted. 11” wide wheels can be used until 3/1/25. Any ECM may be
used."
In AS SPEC LINES, Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep ., add to Notes as follows:
"Any ECM may be used."
In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (82-92) 5.7L V-8 LS1, add to Notes as follows:
"Any ECM may be used."
In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted Prep.5.7L V-8 LT1, add to Notes as follows:
"Any ECM may be used."
In AS SPEC LINES, Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted Prep. 5.7L V-8 LT1; 98-02 , change Notes as follows:
"5.7L LS1:
GM Performance Parts camshaft Kit P/N-19355738 is permitted. Cylinder Bore, 99 mm; Stroke, 92 mm; Intake Valve Diameter,
50.8; Exhaust Valve Diameter, 39.4 mm; Throttle Body Bore, 75 mm; SLP Intake Lid (SLP part number 21044 (98-99) and 21045
(00-02)) is permitted.
Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell.
1-3/4 headers allowed. For the LS1connecting rods Callies P/NCSC6100DS6A2AH, Scat rods P/N2-1CR6100-944, GM performance
rods P/N12649190. Any ECM may be used."
In AS SPEC LINES, Chevrolet Camaro SS (V8) (10-15) Restricted Prep., add to Notes as follows:
"Any ECM may be used."

In STU, Table C, change STU-GT3 charge as follows:
"(Effective January 1, 2026) TABLE C: STU-GT3U"

In STU, Table C, GT3 TCR, add to Notes the following:
"May run DOT approved tire with maximum section width of 275 with 100 pound weight adder. May not run A compound with
275."

In STU Spec Lines, Table A, classify BMW N54/N55 as follows:
STU Maximum Displacement
(cc's) Minimum Weight Notes
BMW N54/N55 3.0 Chart +3% (DI) Short blocks, heads, and intakes may be
freely swapped within these engine
designations. N54 twin turbo not allowed

In STU Spec Lines, Mini Cooper S SC, add to notes:
2100: "May run a 2.285 2.185 diameter pulley."

In STU Spec Lines, Table A, Honda K20C1 Turbo I4, add to Notes the following:
"The 3% DI weight adder does not need to be applied."

In AS Spec Lines, change Notes as follows:
Cadillac CTS-V (04-07) Restricted Prep. 6.0L V8 (Aluminum block, Aluminum heads), LS2, 2 valves/cylinder:
"Any ECM maybe used."
Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep. 6.2L V8 (Aluminum Block, Aluminum Heads), 2 valves per cylinder:
"Any ECM maybe used."
Chevrolet/Pontiac Camaro & Firebird (82-92)s 5.7L V-8 LS1 (Aluminum Block, Aluminum Heads) 2 valves per cylinder:
"Any ECM maybe used."
Chevrolet/Pontiac Camaro & Firebird (93-02):
"Any ECM maybe used."
Chevrolet Camaro SS (V8) (10-15) Restricted Prep. 6.2L V8 (Aluminum Block, Aluminum Heads), 2 valves per cylinder:
"Any ECM maybe used."

In STU Spec Lines, Table C: STU-GT3U, change Minimum Weight as follows:
"150 250 pounds"

In GCR, Section 9.1.6., replace Figure 1 Value Seat Cutting Dimensions with the following:

In AS Spec Lines, change/add to Notes as follows:
Cadillac CTS-V (04-07):
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used. The
Drive Shaft Shop, Axle shaft part #'s 510220/510221 permitted."
Chevrolet Camaro, Pontiac Firebird (70-81) Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #s: 14101081, 14014416 Port Volume (Max.): 081
casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb. weight reduction. Edelbrock Cylinder Head Part
#s 608979, 608879."
Chevrolet Camaro, Pontiac Firebird (70-81) Restricted Prep.:
"Any ECM maybe used."
Chevrolet/Pontiac Camaro & Firebird (82-92) Full Prep.:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #s: 14101081, 14014416 Port Volume (Max.): 081
cast¬ing: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb weight reduction. Edelbrock Cylinder Head Part
#s 608979, 608879 are permitted. For regional competition only, unmodified GM Performance cylinder head part #s 19300955,
19300956 may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186 installed between intake
manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on each side of the restrictor.
All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98,
1.34, 1.00, 0.68 are permitted. Flo Tek Head part #102-500 are permitted."
Chevrolet/Pontiac Camaro & Firebird (82-92) Restricted prep engine:
"Any ECM maybe used."
Chevrolet/Pontiac Camaro & Firebird (93-02) Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #’s: 14101081, 14014416; Port Volume (Max.):
081 casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 250 lb weight reduction. Edelbrock Cylinder Head
Part #’s 608979, 608879 are permitted. For regional competition only, unmodified GM Performance cylinder head part #s
19300955, 19300956 may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186 installed
between intake manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on each side
of the restrictor. All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91, 1.33, 1.00
or 3.27, 1.98, 1.34, 1.00, 0.68 are permitted. Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell. Flo Tek Head part #102-500 are permitted."
Chevrolet/Pontiac Camaro & Firebird (93-02) Restricted Prep:
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used."
Chevrolet Camaro SS (V8) (10-15) Restricted Prep:
"Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is taken from the perimeter of the
stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Any ECM maybe used."
Chevrolet Camaro (10-15) Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #’s: 14101081, 14014416; Port Volume (Max.):
081 casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 200 lb weight reduction. Edelbrock Cylinder Head
Part #’s 608979, 608879 are permitted. Alternate gear ratio sets 2.88, 1.91, 1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 are
permitted. Fuel cells must be located within 24 inches of the standard tank. The 24-inch measurement is taken from the
perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel cell. Flo Tek
Head part #102-500 are permitted. Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement is
taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety fuel
cell."
Chevrolet Camaro (16-) Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #’s: 14101081, 14014416; Port Volume (Max.):
081 casting: 170.00 cc IN/65.00 EX; 416 Casting 168.00cc IN/60.00 EX with a 200 lb weight reduction. Edelbrock Cylinder Head
Part #’s 608979, 608879 are permitted, Flo Tek Head part #102-500 are permitted."
Chevrolet Camaro, 1LE (16-):
"60mm flat plate restrictor required. Any ECM maybe used."
Dodge Challenger (08-20) Restricted Preparation:
"80mm flat plate restrictor is required on the 6.4L engine. Fuel cells must be located within 24 inches of the standard tank. The
24 inch measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell."
Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri (79-86) Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #s: F3ZE AA (GT40), F1ZE-AA (GT-40), F77E-AA
(GT- 40P), Port Volume (Max.): 143.00cc IN/54.00cc EX (GT-40 & GT-40P) with a 250 lb weight reduction. Edelbrock Cylinder
Head Part #s 602579, 602479 are permitted. For regional competition only, unmodified Ford Performance cylinder head part #s
M-6049-Z304DA7, M-6049-Z304D may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186
installed between intake manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on
each side of the restrictor. All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91,
1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 are permitted. Flo Tek Part # 203-500 are permitted."
Ford Mustang Incl. Cobra & Cobra R (79-93) and Mercury Capri(79-86) with Restricted Prep Engine:
"62mm flat plate restrictor is required. Fuel cells must be located within 24 inches of the standard tank. The 24 inch
measurement is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with
installation of a safety fuel cell. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang Including Cobra 94-04 Full Prep:
"Engine built to A/S Build Sheet specifications with the following: Head Casting #s: F3ZE AA (GT40), F1ZE-AA (GT-40), F77E-AA
(GT- 40P), Port Volume (Max.): 143.00cc IN/54.00cc EX (GT-40 & GT-40P) with a 250 lb weight reduction. Edelbrock Cylinder
Head Part #s 602579, 602479 are permitted. For regional competition only, unmodified Ford Performance cylinder head part #s
M-6049-Z304DA7, M-6049-Z304D may be used with Allstar restrictor plate part# ALL26180 and 1.250 inserts part# ALL26186
installed between intake manifold and insulator. Gaskets may be used (each gasket can be no thicker than .125 inches), one on
each side of the restrictor. All intake air must pass through the inserts of the restrictor plate. Alternate gear ratio sets 2.88, 1.91,
1.33, 1.00 or 3.27, 1.98, 1.34, 1.00, 0.68 are permitted. Flo Tek Part # 203-500 are permitted."
Ford Mustang GT (94-04) with Restricted Prep Engine:
"MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang Cobra and GT 94-95(Restricted Prep):
"1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66,
2.43, 1.69, 1.32, 1.00, .68. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang including Cobra 96-04 (Restricted Prep):
"1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66,
2.43, 1.69, 1.32, 1.00, .68. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang Coupe GT (05-14) Restricted Prep.:
"1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66,
2.43, 1.69, 1.32, 1.00, .68. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted. MT82 6 speed is permitted."
Ford Mustang GT (05-14) with Restricted Prep Engine:
"1st Generation 5.0l Coyote 11-14 62mm FPR 2nd Generation 5.0l Coyote 15-17 61mm FPR Alternate transmission Ratios 3.66,
2.43, 1.69, 1.32, 1.00, .68. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted. MT82 6 speed is permitted."
Ford Mustang GT 5.0l (15-17) Restricted Preparation:
"61mm flat plate restrictor required. Fuel cells must be located within 24 inches of the standard tank. The 24 inch measurement
is taken from the perimeter of the stock and alternative fuel cell. Fuel filler location is unrestricted with installation of a safety
fuel cell. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."
Ford Mustang GT 5.0L (2018-):
"60mm flat plate restrictor required. MMR Secondary Timing Chain Tensioner Bracket #467893 is permitted."

In SRF, GCR section 9.1.8.D.1.D, add the following:
"f. Driver Safety and Comfort modifications to seat and controls for drivers with disabilities may be made only by approval. These
modifications must be reported to SCCA Enterprises and noted in the car logbook. The modifications are approved only for the
noted driver with disabilities. If the car is used by or sold to another driver, it must be returned to the previous standard
configuration."

In SRF, GCR section 9.1.8.D.2.K, change as follows:
"OR
SADEV-SRF3 6-Speed Sequential (beginning from Oct. 4, 2021 onward):
1st 12-36 3.0000 : 1
2nd 15-31 2.0667 : 1
3rd 18-28 1.5556 : 1
4th 22-28 1.2727 : 1
5th 24-26 1.0833 : 1
6th 25-23 0.9200 : 1
Final Drive Ratio: 15-48 3.20"

In GCR, Section 9.1.4.1.F.1., change as follows:
"Wheels may not exceed 18 inches in diameter. or 8.0 inches in width for vehicles 2950 lbs. and under minimum allowed race
weight. Vehicles over 2850 minimum allowed race weight may use a 9 inch wide wheel. Cars equal to or less than 2,850 lbs.
minimum allowed race weight may not use wheels wider than 8 inches. Cars greater than 2,850 lbs. minimum allowed race
weight may not use wheels wider than 9 inches."

In AS Spec Lines, Ford Mustang GT 5.0l (15-17), Flat Plate Restrictor Size, change as follows:
"67mm 64mm"

In GCR, Section 9.1.6.F., add the following to Intake Part #’s:
"17113697, 19418185, 89017230, 89017363, 89017364, and 89017365, 12561269 and 88894095"

In STU Spec Line, Table C: STU-GT3U, change as follows:
Minimum Weight: “Current GT3 race weight plus 250 225 pounds”
Notes: "DOT approved tire with maximum section width of 245. GT3 cars base wheel is a maximum of 15”x9”. 18”x9” wheels
allowd with a 3% weight addition. GT3 cars utilizing 15”x7” wheels are limited to a maximum section width of 225 with a 25
pound weight reduction"
"All GT3U (Majors and Runoffs) cars using up to 15"x7" wheels limited to 225 section width tires shall run at current GT3 race
weight plus 225lbs. All Gt3U cars shall run a DOT approved tire with a maximum section width of 245. GT3U cars are allowed
optional 15"x9" wheels with a 1.5% weight addition or up to 18"x9" wheels with a 3.0% weight addition to the total weight
including the 225 lbs."

In AS Spec Lines, Ford Mustang GT (05-14) with Restricted Prep Engine, add to Gear Ratios the following:
"or 3.66, 2.43, 1.69, 1.32, 1.00, .65"

In GCR, Section 9.1.4.G.1, add the following:
"A maximum section width of 245 is permitted. Cars over 3150 lbs. may run a 275 tire with a 2% weight adder."

In AS Spec Lines, Ford Mustang GT 5.0 (2018-), change Weight as follows:
"3600 3525"

In STU, Table A, Mazda MZR (LF, L3, L5), change Notes as follows:
"May use Goodwin Part # 61-2510 or Gato Performance Part #31972 Intake manifold . "

In STU, Table B, classify Honda JDM H23a as follows:
STU Maximum Displacement (cc's) Minimum Weight Notes
Honda JDM H23a 2259 Chart Must meet all ST engine regulations.

In STU Spec Lines, Table C: STU-GT3U, GT3-TCR, change as follows: Remove the current TCR spec line and add the TCR spec lines
from GT3 that are being removed, adding the below to the notes.
"DOT approved tire with maximum section width of 245. May run DOT approved tire with maximum section width of 275 with
100 150 pound weight adder. May not run A-compound with 275. STU-TCR spitters and side valance must comply with
9.1.4.D.3.f. STU-TCR chassis ride height must comply with 9.1.4.1.A.1."

In 9.1.2. GT2/ST Spec Lines, Lotus Evora GT4, change Weight as follows:
"2750 2700"
In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows:
Lotus Elise Cup R: "2300 2250"
Lotus Elise SC/ Lotus Exige SC: "2300 2550
2500 2450"

In STU Table B: Alternate Vehicle and Engine Allowances, change Weight as follows:
Lotus Elise SC/ Lotus Exige SC: "2450 2250"

In SRF, GCR section 9.1.8.D.1.V.ff, change as follows:
"SRF3 Oil Cooler, P/N G480503 or HD Oil Cooler P/N G1148500 may be used as mounted per the GEN3 Assembly Manual. No fan
permitted for SRF. HD Oil Cooler kit P/N G1148500 may be used as mounted per the GEN3 Conversion Manual."

In AS Spec Lines, Cadillac CTS-V (04-07) Restricted Prep., change Weight as follows:
"(Effective 11/1/2025) 3450 3400"

In STU Spec Lines, Table B: Alternate Vehicle and Engine Allowances, Honda K24, change Weight as follows:
"(Effective 11/1/2025) Chart + 2%"

In GCR, Section 9.1.4.H.3, change chart as follows:

A specification table follows in the original; it is not shown here.

In GCR, Section 9.1.4.G.1., change as follows:
"A maximum section width of 245 is permitted. Cars over 3150 lbs. may run a 275 tire with a 2% weight adder."

In AS Spec Lines, Ford Mustang GT(94-04) with Restricted Prep Engine, add to notes the following:
"Ford Motorsport #M-6250-F303 camshaft is permitted."

In STU Spec Lines, Table B: Alternate Vehicle and Engine Allowances, change Minimum Weight as follows:
Honda K20: "Chart + 2%"
Honda K24: "Chart + 2%"

In AS Spec Lines, change Restrictor as follows:
Ford Mustang Incl. Cobra and Cobra R (79-93) and Mercury Capri (79-86) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang GT (94-04) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang Coupe GT (05-14) Restricted Prep 5.0L/6 speed 4 valves per cylinder: "64 mm 61 mm"
Ford Mustang GT (05-14) with Restricted Prep Engine: "64 mm 61 mm"
Ford Mustang GT 5.0L (15-17) Restricted Preparation: "64 mm 61 mm"

In STU Spec Lines, Table A: Alternate Vehicle and Engine Allowances, Mazda MZR (LF, L3, L5), change Notes as follows:
"Short blocks, heads, and intakes may be freely swapped within these engine designations. May use Goodwin Part # 61-
2510 or, Gato Performance Part #31972 or Jack Spania Racing 70 mm sheet-metal aluminum Intake manifold. Must use stock
throttle body or Acura part number 16400-PND-A17."
In STU Spec Lines, Table A: Alternate Vehicle and Engine Allowances, classify Mazda MZR (LF, L3, L5) Turbo as follows:
STU Maximum Displacement (cc's) Minimum Weight Notes
Mazda MZR (LF, L3,
L5) Turbo
Varies Chart Short blocks, heads, and intakes may be freely
swapped within these engine designations. May
use Jack Spania Racing 70 mm sheet-metal
aluminum Intake manifold. Must use stock
throttle body or Acura part number 16400-PND-
A17. Fab9 Tuning bottom-mount turbo kit
approved with one of the STU approved Turbos.

In GCR, Section 9.1.6.D.2.h.2., add the following:
"(Effective 2/1/2026) i. Weight based on full preparation chassis choice spec line for GM LM7 5.3L
Carburetor Option:
Must use the full prep 4776 holly carburetor and spacer gasket
Edelbrock Performer RPM 71187 intake manifold
MSD 6014 ignition box
(Edelbrock part # kit 7118)"

In STU Spec Lines, Table A: Alternate Vehicle and Engine Requirements, Mazda MZR (LF, L3, L5), add to Notes as follows:
"Short blocks, heads, and intakes may be freely swapped within these engine designations. May use Goodwin Part # 61-2510,
Gato Performance Part #31972, or Jack Spania Racing 70 mm sheet-metal aluminum or Fab 9 Elite NC MX5 Performance Intake
manifold. Must use stock throttle body or Acura part number 16400-PND-A17."

This AS Spec Lines re-organization simplifies the Spec Lines for all drivers. This version gives the chassis information on what
engines can be put in their cars. It removes information that is now repeated in the ruleset and adds engine/weight combos as
well as wheelbase/tire size information. The Notes in the Spec Lines have been reviewed to remove information now listed in
the engine build sheets and retain information pertinent to the chassis selected. Where there is nothing in the notes, it is not an
error. It just means everything a driver needs is now in the main rules or the build sheets.
In AS Spec Lines, delete current Spec Line in its entirety as follows:

A specification table follows in the original; it is not shown here.

In SRF, GCR section 9.1.8.D.2.H.18, add the following:
"Spark Plugs: P/N G301041 ONLY NGK LTR7IX-11 / Washers or sealing rings are not allowed for any purpose."