Lap times across years say as much about the weather as the class. % of STU is each class's best lap as a share of STU's on the same day, so the conditions drop out: 100% is level, less is quicker, and a move in it is the class getting faster or slower against the field.
Closest to the field:STU 100.0% of STU Eric Heinrich, Daytona International Speedway Runoffs 2015 race · GTL 92.7% of STU Michael Lewis, Virginia International Raceway Runoffs 2022 race
STUGTLsolid race · dashed qualifying · slower is lower
STUGTLsolid race · dashed qualifying · each class's best lap as a share of STU's at the same event (the reference class, changeable above); 100% is level, less is quicker, so up the chart is quicker
2:24.912Richard Astacio · fastest of 17 · top 5 within 2.6s+1.829s (+1.28%)
2:26.416Richard Astacio · fastest of 16 · top 5 within 1.5s+1.919s (+1.33%)
145.1Hugh Stewart+0.8 mph (+0.5%)
16 rule changes (STU: 15, GTL: 1)5 cars added · 3 weight · 2 induction · 2 tyres & wheels · 4 wording · GT3U wheel and tyre options clarified: 15x7 with 225 section at +275 lbs; 15x9 with 245 section at +275 lbs plus 1.5%; 16–18x9 with 245 section at +275 lbs plus 3.0%. · STU cars at or under 2,825 lbs minimum weight limited to 8-inch wheels; over 2,825 lbs limited to 9-inch wheels. · STU GT3U minimum weight increases from GT3 race weight plus 225 to plus 275 pounds; 2.0L unrestricted engines add 75 lbs. · STU adds BMW M50B20TU engine, 1991 cc, minimum weight per chart, must meet all STU engine regulations. · STL, STU weight calculation procedure clarified: positive percentages added first, negative subtracted second, then fixed weights applied. · STU Honda K20C1 Turbo I4 turbo restrictor increases from 35mm to 36mm TIR. · STU GT86 Cup car must meet 2022 Toyota GR Cup rules, tires maximum 245 section width. · STU Mazda Renesis Street Port added to Table B with 2450 lbs minimum weight and 70mm throttle body options. · STU eliminates 33 and 34 mm inlet restrictor options, removing minimum weights of 2380 and 2525 lbs. · GT3U class removed from GCR; GT3U cars now compete in STU. · STU Mazda MZR engines may now use Fab 9 Elite NC MX5 Performance Intake manifold as alternative option. · STU Mazda MZR (LF, L3, L5) Turbo added; Goodwin intake removed, Jack Spania Racing 70 mm intake and Fab9 Tuning bottom-mount turbo kit approved. · STU 36mm restrictor revised to 2830 cc, 37mm to 2980 cc. · STU removes 275 tire option and 2% weight adder for cars over 3150 lbs; maximum section width now 245. · STU Honda K20 and K24 engines lose 2% weight penalty; minimum weight now per chart only. · STU Honda K24 engine swap weight increases by 2 percent, effective November 1, 2025.showhide
STU Wheel and tire requirements for GT3U #40679wordingwordingGT3U wheel and tyre options clarified: 15x7 with 225 section at +275 lbs; 15x9 with 245 section at +275 lbs plus 1.5%; 16–18x9 with 245 section at +275 lbs plus 3.0%.
STU 9” Wheels #40433tyres & wheelsslowertyres & wheelsSTU cars at or under 2,825 lbs minimum weight limited to 8-inch wheels; over 2,825 lbs limited to 9-inch wheels.
STU Weight adjustment to former GT3U cars #40474weightslowerweightSTU GT3U minimum weight increases from GT3 race weight plus 225 to plus 275 pounds; 2.0L unrestricted engines add 75 lbs.
STU Request to allow BMW M50B20TU engine in STU #40202cars addedaddedSTU adds BMW M50B20TU engine, 1991 cc, minimum weight per chart, must meet all STU engine regulations.
STU Calculating Weight #40224wordingwordingSTL, STU weight calculation procedure clarified: positive percentages added first, negative subtracted second, then fixed weights applied.
STU Turbo Restrictor Size Increase Request #40008inductionfasterinductionSTU Honda K20C1 Turbo I4 turbo restrictor increases from 35mm to 36mm TIR.
STU GT86 Cups Car in STU #40028wordingwordingSTU GT86 Cup car must meet 2022 Toyota GR Cup rules, tires maximum 245 section width.
STU Mazda Rx-8 Renesis - Streetported Variant & Added Weight #39785cars addedaddedSTU Mazda Renesis Street Port added to Table B with 2450 lbs minimum weight and 70mm throttle body options.
STU Eliminate 33 and 34 mm TIRs #39872inductionremovedinductionSTU eliminates 33 and 34 mm inlet restrictor options, removing minimum weights of 2380 and 2525 lbs.
GTL Remove GT3U from GCR as it is now in STU #39862cars addedremovedcars addedGT3U class removed from GCR; GT3U cars now compete in STU.
STU Fab 9 Racing Intake Manifold in STU #39767cars addedaddedSTU Mazda MZR engines may now use Fab 9 Elite NC MX5 Performance Intake manifold as alternative option.
STU Request for Permission on Aftermarket Turbo Kit and Intake #39529cars addedaddedSTU Mazda MZR (LF, L3, L5) Turbo added; Goodwin intake removed, Jack Spania Racing 70 mm intake and Fab9 Tuning bottom-mount turbo kit approved.
STU Turbo Inlet Restrictor Table #38961wordingwordingSTU 36mm restrictor revised to 2830 cc, 37mm to 2980 cc.
STU 275 Tire Rule #38983tyres & wheelsslowertyres & wheelsSTU removes 275 tire option and 2% weight adder for cars over 3150 lbs; maximum section width now 245.
STU STU Honda Engine weight penalty #39375weightfasterweightSTU Honda K20 and K24 engines lose 2% weight penalty; minimum weight now per chart only.
STU Non-Homologated Engine Swaps - Specifically K24A2 w/ Honda CRZ #38746weightslowerweightSTU Honda K24 engine swap weight increases by 2 percent, effective November 1, 2025.
2:23.083Peter Cunningham · fastest of 16 · top 5 within 2.6s-3.144s (-2.15%)
2:24.497Chip Herr · fastest of 15 · top 5 within 3.8s-1.327s (-0.91%)
144.3Chip Herr-1.0 mph (-0.7%)
21 rule changes (STU: 18, GTL: 3)6 weight · 4 cars added · 4 engine · 3 tyres & wheels · 1 induction · 3 wording · STU Lotus Elise SC and Exige SC weight reduced from 2450 to 2250 lbs. · STU-TCR gains GT3 TCR spec lines; 275 tyre option now costs 150 lb adder, up from 100 lb. · Lotus Evora GT4 minimum weight drops to 2700 lbs; Elise Cup R to 2250 lbs; Elise SC and Exige SC to 2450–2550 lbs. · STU 2.8–3.2L N/A engines now permit 245 max tyre width; over 3150 lbs cars may run 275 with 2% weight penalty. · STU Mazda MZR intake manifold now allows Goodwin 61-2510 or Gato Performance 31972. · STU Honda JDM H23a added, 2259 cc, minimum weight per chart, must meet ST engine regulations. · STU wheels capped at 18 inches diameter; under 2,850 lbs max 8 inches wide, over 2,850 lbs max 9 inches wide. · STU-GT3U minimum weight reduced from plus 250 to plus 225 pounds; wheel and tyre options clarified with weight adjustments. · STU BMW N54/N55 3.0 classified at chart plus 3% minimum weight; N54 twin turbo not allowed. · STU Mini Cooper S SC pulley diameter reduced to 2.185 inches. · STU Honda K20C1 Turbo I4 exempted from 3% direct injection weight adder. · STU GT3U minimum weight increases 150 pounds to 250 pounds. · TA2 rear wing height rule clarified: OEM aerodynamic devices exempt from peak-of-roof height limit. · STU Audi 1.8T Wagon removed; Porsche 944 1800cc weight to Chart, turbo inlet restrictor deleted. · STU-GT3 reclassified as STU-GT3U, effective 1 January 2026. · STU GT3 TCR may run 275-wide DOT tires with 100 lb weight penalty; A compound prohibited at 275. · STL STU Mazda Miata alternate front hubs Mazda Motorsports Development Part #0000-04-5HUB-S1 approved. · STU BMW N54/N55 turbo inlet restrictors now required per GCR definition; twin turbo conversion to single turbo clarified. · GTL Toyota G16E-GTS removes direct injection prohibition, allowing direct injection engines. · GTL L16 limited prep gains 32mm choke option at 1910 lbs, compression capped 12.0:1, valve lift .450 max. · STU Mini Cooper S SC: 1900 stock pulley spec to 2.565 diameter; 2100 now permits 2.285 diameter pulley.showhide
STU Lotus Weight Reduction E&O #38919weightfasterweightSTU Lotus Elise SC and Exige SC weight reduced from 2450 to 2250 lbs.
STU STU-TCR Adjustments #38723weightslowerweightSTU-TCR gains GT3 TCR spec lines; 275 tyre option now costs 150 lb adder, up from 100 lb.
STU Lotus Weight Reduction #38772weight -50 lbsfasterweightLotus Evora GT4 minimum weight drops to 2700 lbs; Elise Cup R to 2250 lbs; Elise SC and Exige SC to 2450–2550 lbs.
STU 2.8-3.2L N/A Engine Allowances #38007tyres & wheelsfastertyres & wheelsSTU 2.8–3.2L N/A engines now permit 245 max tyre width; over 3150 lbs cars may run 275 with 2% weight penalty.
STU 2006-2015 Mazda Miata Intake Manifold #38422engineaddedengineSTU Mazda MZR intake manifold now allows Goodwin 61-2510 or Gato Performance 31972.
STU Requesting Approval of the JDM Honda h23a #38489cars addedaddedSTU Honda JDM H23a added, 2259 cc, minimum weight per chart, must meet ST engine regulations.
STU Wheel Size Inconsistency #38018tyres & wheelstyres & wheelsSTU wheels capped at 18 inches diameter; under 2,850 lbs max 8 inches wide, over 2,850 lbs max 9 inches wide.
STU Table C: STU-GT3U Clarification #38268weightfasterweightSTU-GT3U minimum weight reduced from plus 250 to plus 225 pounds; wheel and tyre options clarified with weight adjustments.
STU BMW N54/N55 Engine Allowance Follow Up #37447cars addedaddedSTU BMW N54/N55 3.0 classified at chart plus 3% minimum weight; N54 twin turbo not allowed.
STU STU Mini Cooper pulley size clarification re: letter #36980 #37717inductionfasterinductionSTU Mini Cooper S SC pulley diameter reduced to 2.185 inches.
STU Question About a Weight Modifier #37782weightfasterweightSTU Honda K20C1 Turbo I4 exempted from 3% direct injection weight adder.
STU Increase Minimum Weight #37919weight +100 lbsslowerweightSTU GT3U minimum weight increases 150 pounds to 250 pounds.
GTL Correct language regarding OEM Areo Devices #37137wordingwordingTA2 rear wing height rule clarified: OEM aerodynamic devices exempt from peak-of-roof height limit.
STU Audi 1.8t Wagon STU Table B #36685cars addedremovedcars addedSTU Audi 1.8T Wagon removed; Porsche 944 1800cc weight to Chart, turbo inlet restrictor deleted.
STU Merger GT3 to STU #37486wordingunclearSTU-GT3 reclassified as STU-GT3U, effective 1 January 2026.
STU GT3 TCR Tire allowance #37494tyres & wheelsaddedtyres & wheelsSTU GT3 TCR may run 275-wide DOT tires with 100 lb weight penalty; A compound prohibited at 275.
STU Request to Remove Miata Hubs from General category #37138cars addedaddedSTL STU Mazda Miata alternate front hubs Mazda Motorsports Development Part #0000-04-5HUB-S1 approved.
STU BMW N54/N55 Engine Allowance #37146wordingwordingSTU BMW N54/N55 turbo inlet restrictors now required per GCR definition; twin turbo conversion to single turbo clarified.
GTL G16E-GTS Fuel Injection Spec Line Change #36588engineaddedengineGTL Toyota G16E-GTS removes direct injection prohibition, allowing direct injection engines.
GTL GTL Alternate Weight and Choke Option for L16 engine #36653engineaddedengineGTL L16 limited prep gains 32mm choke option at 1910 lbs, compression capped 12.0:1, valve lift .450 max.
STU R53 15% Pulley Request #36980enginefasterengineSTU Mini Cooper S SC: 1900 stock pulley spec to 2.565 diameter; 2100 now permits 2.285 diameter pulley.
2:26.227Thomas Noble · fastest of 18 · top 5 within 2.3s-1.656s (-1.12%)
2:25.824Thomas Noble · fastest of 17 · top 5 within 2.4s-2.586s (-1.74%)
145.3Thomas Noble+1.1 mph (+0.8%)
2:30.858Peter Shadowen · fastest of 14 · top 5 within 4.4s-1.085s (-0.71%)
2:30.844Chris Bovis · fastest of 13 · top 5 within 3.7s-0.757s (-0.50%)
133.3Peter Shadowen+1.8 mph (+1.4%)
+5.020squal +4.631s
103.4%qual 103.2%
20 rule changes (STU: 4, GTL: 16)5 cars added · 3 aero · 3 engine · 3 weight · 2 induction · 2 wording · 2 other · GTL adds Toyota GR86 2021–2023, 2dr RWD, 101.3 in wheelbase. · GTL adds Spec Miata 1990–2005 with legal Spec Miata engine and intake system. · GTL adds Mazda MX5 RF 2017- model with 91.0 in wheelbase. · STU RWD turbo cars no longer required to reduce inlet restrictor by 1 mm from table minimum. · GTL added to GT3 choke option line in GCR 9.1.2.E.13.n. · GT2-ST Acura NSX minimum weight rises to 3000 lbs, restrictor increases to 45mm TIR. · GTL Datsun 510 Limited Prep fuel induction increased to 34 mm chokes, minimum weight rises to 2000 lbs. · STU Mini Cooper S SC gains alternate LEAP OMICRON hood scoop part LEP-OMICRON3 as permitted option. · STU BMW S54 B32 OEM dry sump oiling system now permitted. · GT1-GTX rear blade spoiler: angle 50–75°, max 59.0 wide by 5.0 high inches; total area limit removed. · GT1, GT2, GT3, GTL, GTX Direct Injection now permitted if original equipment. · GT2 Nissan and GT3 Mazda, Mitsubishi 4G93, Nissan QR25DE/DD, QE25DE/DD now permit Direct Injection per 9.1.2.F.7.5.E. · STL and STU now permit electric power steering pumps, OEM electric-assisted steering, or column-mounted electric steering assist systems. · GTL 12A rotary engines may machine and use 13B housing to O.E. 12A spec across all port types. · GTL Toyota DR86 2021–2024 added to class. · GTL BMW Mini model years changed to 2002-2013. · GTL small unrestricted engines under 1399cc lose 38–79 lbs across Alfa, AMC, Triumph, Mini, Sprite, Fiat, Ford, Honda, Mazda, Nissan, Subaru, Toyota, Volkswagen. · GTL Honda Fit 2009-13 2-door FWD added with 99.0 in wheelbase, alternate 94.0 and 97.0 in. · GTL spec lines moved contiguous with GT2 and GT3; GTA category and specs renumbered behind GTL; P2 engine tables reorganised with restrictor and weight specifications clarified. · GTL Nissan Sentra/200SX A 1400 minimum weight reduced to 1800 lbs.showhide
GTL Request to Include Toyota GR86 in GTL #36324cars addedaddedGTL adds Toyota GR86 2021–2023, 2dr RWD, 101.3 in wheelbase.
GTL Inclusion of Modified Spec Miata for GTL competition #36325cars addedaddedGTL adds Spec Miata 1990–2005 with legal Spec Miata engine and intake system.
GTL Include Mazda MX5 RF 2017- in GTL #36428cars addedaddedGTL adds Mazda MX5 RF 2017- model with 91.0 in wheelbase.
STU RWD Turbo Disadvantage #36255inductionfasterinductionSTU RWD turbo cars no longer required to reduce inlet restrictor by 1 mm from table minimum.
GTL Add GTL to GT3 choke option line. #36236otheraddedGTL added to GT3 choke option line in GCR 9.1.2.E.13.n.
GTL Request for Spec Line 1010 Reconsideration #35009weight +300 lbsslowerweightGT2-ST Acura NSX minimum weight rises to 3000 lbs, restrictor increases to 45mm TIR.
GTL Allow 34 mm chokes for the Datsun 510 #35661induction +50 lbsfasterinductionGTL Datsun 510 Limited Prep fuel induction increased to 34 mm chokes, minimum weight rises to 2000 lbs.
STU Letter #35397 addendum #35453aeroaddedaeroSTU Mini Cooper S SC gains alternate LEAP OMICRON hood scoop part LEP-OMICRON3 as permitted option.
STU S54 Drysump #35464otheraddedSTU BMW S54 B32 OEM dry sump oiling system now permitted.
GTL Rear Blade Spoiler Clarification #35261aeroaeroGT1-GTX rear blade spoiler: angle 50–75°, max 59.0 wide by 5.0 high inches; total area limit removed.
GTL GT Direct Injection allowance and rules #35437engineaddedengineGT1, GT2, GT3, GTL, GTX Direct Injection now permitted if original equipment.
GTL GT2/3 remove Direction Injection not allowed in Spec line notes #35439engineaddedengineGT2 Nissan and GT3 Mazda, Mitsubishi 4G93, Nissan QR25DE/DD, QE25DE/DD now permit Direct Injection per 9.1.2.F.7.5.E.
STU ST Electric-Assisted Steering Systems #35066aeroaddedaeroSTL and STU now permit electric power steering pumps, OEM electric-assisted steering, or column-mounted electric steering assist systems.
GTL Rotary Engine 12A Rotor Housings #35131engineaddedengineGTL 12A rotary engines may machine and use 13B housing to O.E. 12A spec across all port types.
GTL Request to Include Toyota GR86 in GTL #35198cars addedaddedGTL Toyota DR86 2021–2024 added to class.
GTL Errors and Omissions, GTL engines & Cars #35226wordingwordingGTL BMW Mini model years changed to 2002-2013.
GTL Small Engines in GT Lite #34842weightfasterweightGTL small unrestricted engines under 1399cc lose 38–79 lbs across Alfa, AMC, Triumph, Mini, Sprite, Fiat, Ford, Honda, Mazda, Nissan, Subaru, Toyota, Volkswagen.
GTL Request to Classify Honda Fit body in GTL #35020cars addedaddedGTL Honda Fit 2009-13 2-door FWD added with 99.0 in wheelbase, alternate 94.0 and 97.0 in.
GTL Errors in GTCS Headings and Use of the Terms Category and ClassChange existing GTL and GTA Rules #34453wordingwordingGTL spec lines moved contiguous with GT2 and GT3; GTA category and specs renumbered behind GTL; P2 engine tables reorganised with restrictor and weight specifications clarified.
GTL Weight for Nissan Sentra/200SX A 1400's #34918weight -50 lbsfasterweightGTL Nissan Sentra/200SX A 1400 minimum weight reduced to 1800 lbs.
2:00.389Johan Schwartz · fastest of 13 · top 5 within 2.3s-0.226s (-0.19%)
2:02.302Mark Liller · fastest of 14 · top 5 within 1.6s-30.055s (-19.73%)
144.0Mark Liller+0.1 mph (+0.1%)
2:09.564Peter Shadowen · fastest of 11 · top 5 within 4.9s+1.775s (+1.39%)
2:11.277Graham Fuller · fastest of 10 · top 5 within 2.4s-9.903s (-7.01%)
142.7Peter Shadowen+6.7 mph (+4.9%)
+8.975squal +9.175s
107.3%qual 107.6%
10 rule changes (STU: 3, GTL: 7)5 cars added · 2 engine · 2 weight · 1 wording · STU adds 2022 Toyota GR Cup and GR86 Cup, both 2387cc, 2700 lbs, 18-inch wheels, 245/620R18 slicks. · Fields Cardinal V8 added to GT1 with Ford V8 engine, 4.9L, 2100 lbs, fuel injection. · STU Mazda BP5A now classified at 1839 cc displacement, 2510 lbs minimum weight, alternate intake manifold permitted. · STU minimum weights adjusted: 2450 cc to 2595 lbs, 2600 cc to 2710 lbs. · GTL 3K, 4K, 5K Toyota engines may now use 4Y block only. · GT2 and GTL add Toyota 4A-F and 4A-FE 1.6L DOHC 16V engines as permitted options. · GTL Fiat X1/9 1500 Limited Prep minimum weight increases to 2000 lbs from 1835 lbs. · GT2 TA2 and GTA throttle body part numbers updated to GM 12570790 or Edelbrock 33869/3870. · GTL adds Ford Festiva 1988-1993 FWD hatchback with Mazda B3 1324cc engine. · GTL adds Toyota G16E-GTS 1618cc DOHC 3-cyl engine, 1945 lbs, SIR, no turbo or direct injection.showhide
STU 2022 Toyota GR Cup for STU #34449cars addedaddedSTU adds 2022 Toyota GR Cup and GR86 Cup, both 2387cc, 2700 lbs, 18-inch wheels, 245/620R18 slicks.
GTL Please classify Fields Cardinal V8 #33784cars addedaddedFields Cardinal V8 added to GT1 with Ford V8 engine, 4.9L, 2100 lbs, fuel injection.
STU Alternate OEM Miata Intake Manifold #33827engineaddedengineSTU Mazda BP5A now classified at 1839 cc displacement, 2510 lbs minimum weight, alternate intake manifold permitted.
STU E&O STU NA Weight Chart. #33737weightfasterweightSTU minimum weights adjusted: 2450 cc to 2595 lbs, 2600 cc to 2710 lbs.
GTL Toyota 4Y Engine Classification Request #33562engineaddedengineGTL 3K, 4K, 5K Toyota engines may now use 4Y block only.
GTL Toyota 4A-F and 4A-FE 1.6L DOHC 16V Engine Request #33415cars addedaddedGT2 and GTL add Toyota 4A-F and 4A-FE 1.6L DOHC 16V engines as permitted options.
GTL Fiat HP Limited Prep X1/9 Weight in GTL #33297weightslowerweightGTL Fiat X1/9 1500 Limited Prep minimum weight increases to 2000 lbs from 1835 lbs.
GTL GT2 (TA2)/GTA Part Number Update #33315wordingwordingGT2 TA2 and GTA throttle body part numbers updated to GM 12570790 or Edelbrock 33869/3870.
GTL Request to add Ford Festiva to GTL #33335cars addedaddedGTL adds Ford Festiva 1988-1993 FWD hatchback with Mazda B3 1324cc engine.
GTL Engine Request #33064cars addedaddedGTL adds Toyota G16E-GTS 1618cc DOHC 3-cyl engine, 1945 lbs, SIR, no turbo or direct injection.
2:00.615Johan Schwartz · fastest of 21 · top 5 within 2.6s+0.667s (+0.56%)
2:32.357Mark Liller · fastest of 19 · top 5 within 4.3s+31.874s (+26.46%)
143.9Johan Schwartz+0.1 mph (+0.1%)
2:07.789Peter Shadowen · fastest of 14 · top 5 within 2.2s+0.792s (+0.62%)
2:21.180Michael Lewis · fastest of 13 · top 5 within 2.1s+13.343s (+10.44%)
136.0Peter Shadowen+4.9 mph (+3.7%)
-11.177squal +7.174s
92.7%qual 105.9%
24 rule changes (STU: 21, GTL: 3)6 weight · 4 cars added · 4 engine · 2 aero · 2 tyres & wheels · 6 wording · GT1, GT2, GT3, GTL, GTX tail lights may now be original style or custom panel graphic with functioning red LED brake lamps. · STU Mazda 13B Turbo added as Chart Limited displacement, streetport only, alternative turbos only. · STU OEM louver vents no longer count against vent allowance or 200 square inch limit. · STU non-4-valve engines gain 9% base engine weight reduction allowance; 2400cc minimum weight drops 1 lb to 2595. · STU normally-aspirated engines 2976cc–3200cc with single throttle body lose 10% base engine weight reduction allowance. · ST removes redundant language about engine balance shaft removal and alternate pulley installation. · STU cars that qualified for 9 inch wheels in 2021 may continue running them through 2022 only. · STU splitter definition clarified: must attach to lowest point of front, have no vertical deviations. · STU BMW E36 M3 (95-99) S52B32 minimum weight cut to 3110 lbs from 3200, displacement to 3152 cc. · STU BMW S50B32 Euro maximum displacement 3201 cc, minimum weight 3300 lbs, permits 0.040 overbore and 0.5 compression increase. · ST engine swap origin rule narrowed: North America changed to United States only for case-by-case approval. · STU Honda CRX 84-91 and Civic Del Sol 93-97 both ineligible for front-wheel-drive weight reductions. · STU wheel width rule clarified: under 2950 lbs uses max 8.0 inches, 2950 lbs and over uses max 9.0 inches. · STU single-throttle body cars get lower minimum weights: 2450cc to 2596 lbs, 2500cc to 2635 lbs, 2550cc to 2675 lbs. · Ginetta G40 added to GTL with Ford Zetec 1796cc engine, 2050 lbs minimum weight, 22.5mm SIR. · STU single throttle body weight reduction removed; minimum weights revised down to 2990 lbs at 3000cc from 3300 lbs. · STU Audi A4 1.8T minimum weight fixed to 3050 lbs, K04 turbo removed, VF30 with 35mm restrictor required; Porsche 944 1800 weight fixed to 3050 lbs, VW/Audi 1.8L engine removed, 35mm inlet restrictor required. · STL and STU Improved Touring vehicles must now conform to section 9.1.4 Tires & Wheels. · STU engines may delete balance shafts and plug openings; alternate pulleys or gears allowed only for timing belt or chain operation. · STU hood vents now allow louvers within 200 square inches. · STU adds Honda K23 with 2354 cc displacement and chart minimum weight, K24 block allowed with K23 internals and head. · STU Honda K23 relaxes internal engine requirement, now needs only K23 crankshaft. · STL/STU intake manifold and cylinder head porting clarified as free; intake and exhaust porting wording removed. · GT3 Volkswagen Fun Cup Beetle EVO3 classified, sealed SOHC 1984cc engine, 2060 lbs minimum weight.showhide
GTL Tail lights on all GT category race cars. #32799wordingwordingGT1, GT2, GT3, GTL, GTX tail lights may now be original style or custom panel graphic with functioning red LED brake lamps.
STU Request Mazda 13 B turbo #32668cars addedaddedSTU Mazda 13B Turbo added as Chart Limited displacement, streetport only, alternative turbos only.
STU Hood Vents and Intercooler Scoops #32733aeroaddedaeroSTU OEM louver vents no longer count against vent allowance or 200 square inch limit.
STU Non 4 valve weight reduction removed #32808weightfasterweightSTU non-4-valve engines gain 9% base engine weight reduction allowance; 2400cc minimum weight drops 1 lb to 2595.
STU Error in new minimum weight table when combined with other text #32711engineslowerengineSTU normally-aspirated engines 2976cc–3200cc with single throttle body lose 10% base engine weight reduction allowance.
STU Redundant Language in May GCR #32713wordingwordingST removes redundant language about engine balance shaft removal and alternate pulley installation.
STU Opposed to the Proposed STU Weight Chart #32381tyres & wheelsaddedtyres & wheelsSTU cars that qualified for 9 inch wheels in 2021 may continue running them through 2022 only.
STU Clarification request for GCR 9.1.4.D.3.a Splitter Definition #32414wordingwordingSTU splitter definition clarified: must attach to lowest point of front, have no vertical deviations.
STU Request Adjustment to Min Weight for STU BMW E36 M3 (95-99) #31535weight -90 lbsfasterweightSTU BMW E36 M3 (95-99) S52B32 minimum weight cut to 3110 lbs from 3200, displacement to 3152 cc.
STU BMW E36 M3 Canadian (North American) S50B32 engine #31866engineaddedengineSTU BMW S50B32 Euro maximum displacement 3201 cc, minimum weight 3300 lbs, permits 0.040 overbore and 0.5 compression increase.
STU Engine Swap Origin Country #32209wordingwordingST engine swap origin rule narrowed: North America changed to United States only for case-by-case approval.
STU CRX/Civic Del Sol #32214weightslowerweightSTU Honda CRX 84-91 and Civic Del Sol 93-97 both ineligible for front-wheel-drive weight reductions.
STU Error correction #32383wordingwordingSTU wheel width rule clarified: under 2950 lbs uses max 8.0 inches, 2950 lbs and over uses max 9.0 inches.
STU Single TB Weight Modifiers Add to Chart #32393weightfasterweightSTU single-throttle body cars get lower minimum weights: 2450cc to 2596 lbs, 2500cc to 2635 lbs, 2550cc to 2675 lbs.
GTL Request to Classify Ginetta G40 in GTL #31599cars addedaddedGinetta G40 added to GTL with Ford Zetec 1796cc engine, 2050 lbs minimum weight, 22.5mm SIR.
STU Single TB Weight Modifiers #31449weightfasterweightSTU single throttle body weight reduction removed; minimum weights revised down to 2990 lbs at 3000cc from 3300 lbs.
STU Request to Remove A4 1.8t from STU Spec Line Tables #31465weightslowerweightSTU Audi A4 1.8T minimum weight fixed to 3050 lbs, K04 turbo removed, VF30 with 35mm restrictor required; Porsche 944 1800 weight fixed to 3050 lbs, VW/Audi 1.8L engine removed, 35mm inlet restrictor required.
STU Improved Touring Tires #32063tyres & wheelstyres & wheelsSTL and STU Improved Touring vehicles must now conform to section 9.1.4 Tires & Wheels.
STU Request Allowance for Balance Shaft Delete in STU #31434enginefasterengineSTU engines may delete balance shafts and plug openings; alternate pulleys or gears allowed only for timing belt or chain operation.
STU Request Louvers in hood vents #31916aeroaddedaeroSTU hood vents now allow louvers within 200 square inches.
STU Request to Add Honda K23 Spec Line #30682cars addedaddedSTU adds Honda K23 with 2354 cc displacement and chart minimum weight, K24 block allowed with K23 internals and head.
STU RE: Aug FT letter 30682 #31060enginefasterengineSTU Honda K23 relaxes internal engine requirement, now needs only K23 crankshaft.
STU Throttling Device Clarification #31323wordingwordingSTL/STU intake manifold and cylinder head porting clarified as free; intake and exhaust porting wording removed.
GTL Request car classification #31032cars addedaddedGT3 Volkswagen Fun Cup Beetle EVO3 classified, sealed SOHC 1984cc engine, 2060 lbs minimum weight.
1:47.078Joe Moser · fastest of 30 · top 5 within 2.0s-1.843s (-1.69%)
1:47.441Joe Moser · fastest of 28 · top 5 within 1.8s-1.946s (-1.78%)
146.9Kip VanSteenburg
1:51.819Christopher Bovis · fastest of 22 · top 5 within 1.8s+1.488s (+1.35%)
1:51.952Scott Twomey · fastest of 19 · top 5 within 1.7s-0.116s (-0.10%)
129.5Brian Linn
+4.511squal +4.741s
104.2%qual 104.4%
20 rule changes (STU: 12, GTL: 8)5 cars added · 2 aero · 2 induction · 1 engine · 1 suspension & brakes · 1 weight · 6 wording · 2 other · GTA part numbers updated: 0-80541-1 to 0-80541-2 in two locations and 6010 to 6014X in TA2 Appendix. · GTL Honda B18 split into B18A/B at 1797 cc 2050 lbs and B18C at 1834 cc 2065 lbs. · GTL Nissan B13 Sentra may have hood bulge maximum 1.5 inches high by 10.0 long by 6.0 wide. · unclear · STU fender flare wording clarified: flare of exterior contour may not change wheel opening size, location or shape from side view. · STU Mazda 12A Bridgeport weight reduced from 2550 lbs to 2350 lbs. · STU fender flare rules clarified: maximum 2 inches total, must cover tire contact patch from above, cannot alter body configuration or wheel opening geometry. · STU Honda S2000 now allows F20/F22 K24 crankshaft with chart weight for achieved displacement. · ST oil coolers and filters now explicitly listed as addable or substitutable parts in vents and breathers section. · GTL Mazda 12A SIR increases to 29mm, minimum weight rises to 2000 lbs, 28mm SIR option with 175 lb penalty removed. · ST 90-05 Mazda Miata allowed alternate front wheel hub Mazda Motorsports Development Part #0000-04-5HUB-S1. · GTL adds FIAT X-1/9 Bertone 1500 SOHC, 1498 cc, 2000 lbs, fuel injection or carburetors permitted. · ST cars may now relocate ABS actuation hardware and wiring anywhere in the engine compartment. · STU Porsche PDK automatic transmission limited to 8 forward speeds; sequential DCT systems require 3.5% minimum weight increase. · STU Mazda 13B Street Port 2400 removes choke location rule, allows auto-type 2bbl with any dual-Y manifold. · STU driveshaft and half-shafts now explicitly permitted in steel or aluminum, removing OEM material requirement. · GTL Nissan MRA8DE 1.8L engine added, 1797 cc, DOHC, 2050 lbs minimum weight. · GTL Mazda 13B SIR increases from 26 mm to 28 mm; 27 mm option with 175 lbs removed. · STU Mazda 13B Spec and Bridge Port removed; Street Port added at 2400 lbs minimum weight. · ST aero devices and reference areas must include end plates, exclude fasteners under 1/2" protrusion.showhide
GTL Request to Update GTA Obsolete Part Numbers #30615wordingwordingGTA part numbers updated: 0-80541-1 to 0-80541-2 in two locations and 6010 to 6014X in TA2 Appendix.
GTL Request clarification for the Honda B18a,bVS B18c #30482cars addedaddedGTL Honda B18 split into B18A/B at 1797 cc 2050 lbs and B18C at 1834 cc 2065 lbs.
GTL Request to Allow Hood Bulge on Nissan B13 Sentra #30504aeroaddedaeroGTL Nissan B13 Sentra may have hood bulge maximum 1.5 inches high by 10.0 long by 6.0 wide.
GTL Request BMW E21 Classing #30582otherunclearunclear
STU STU Fender flares #30696wordingwordingSTU fender flare wording clarified: flare of exterior contour may not change wheel opening size, location or shape from side view.
STU Request weight reduction for 12A bridgeport motor in Miata #30751weight -200 lbsfasterweightSTU Mazda 12A Bridgeport weight reduced from 2550 lbs to 2350 lbs.
STU Request for Fender Flare Clarification #30375wordingwordingSTU fender flare rules clarified: maximum 2 inches total, must cover tire contact patch from above, cannot alter body configuration or wheel opening geometry.
STU Provision for Interchangeable Engine Components Already Allowed #30342engineaddedengineSTU Honda S2000 now allows F20/F22 K24 crankshaft with chart weight for achieved displacement.
STU ST Oil Coolers E&O Correction to 9.1.4.2.H #30388wordingwordingST oil coolers and filters now explicitly listed as addable or substitutable parts in vents and breathers section.
GTL Request for Help for Mazda 12A #29754induction +50 lbsslowerinductionGTL Mazda 12A SIR increases to 29mm, minimum weight rises to 2000 lbs, 28mm SIR option with 175 lb penalty removed.
STU Super Touring Alternate Miata Hubs #30345cars addedaddedST 90-05 Mazda Miata allowed alternate front wheel hub Mazda Motorsports Development Part #0000-04-5HUB-S1.
GTL Request LP HP Fiat X1/9 & Bertone 1500 to GTL #30058cars addedaddedGTL adds FIAT X-1/9 Bertone 1500 SOHC, 1498 cc, 2000 lbs, fuel injection or carburetors permitted.
STU Brake Component Relocation #29990suspension & brakessuspension & brakesST cars may now relocate ABS actuation hardware and wiring anywhere in the engine compartment.
STU Porsche PDK #30081wordingwordingSTU Porsche PDK automatic transmission limited to 8 forward speeds; sequential DCT systems require 3.5% minimum weight increase.
STU Reference Letter #29333 Proposed STU 13B Spec Line Changes #30086wordingwordingSTU Mazda 13B Street Port 2400 removes choke location rule, allows auto-type 2bbl with any dual-Y manifold.
STU Drive Shaft Request #30087otherotherSTU driveshaft and half-shafts now explicitly permitted in steel or aluminum, removing OEM material requirement.
GTL Increase 13b SIR size #29867inductionfasterinductionGTL Mazda 13B SIR increases from 26 mm to 28 mm; 27 mm option with 175 lbs removed.
STU 13B Rules Adjustment #29333cars addedremovedcars addedSTU Mazda 13B Spec and Bridge Port removed; Street Port added at 2400 lbs minimum weight.
STU Request clarification on wing measurement #29640aeroaeroST aero devices and reference areas must include end plates, exclude fasteners under 1/2" protrusion.
2:27.883David Fiorelli · fastest of 14 · top 5 within 4.1s
2:28.410Anthony Geraci · fastest of 14 · top 5 within 3.1s
144.2David Fiorelli
2:31.943Chris Bovis · fastest of 14 · top 5 within 6.3s
2:31.601Peter Shadowen · fastest of 14 · top 5 within 7.2s
131.4Peter Shadowen
+3.191squal +4.060s
102.2%qual 102.7%
34 rule changes (STU: 17, GTL: 17)5 cars added · 4 aero · 4 engine · 3 weight · 1 induction · 1 suspension & brakes · 13 wording · 3 other · GT1/GT2/GT3/GTL/GTX turbocharging and supercharging now permitted if listed on spec line. · STU fender flare rule reworded: now per-corner up to 2" total, 1% weight penalty applies to entire modification. · GTL Mazda 13B restrictor increases from 24mm to 26mm SIR, minimum weight rises to 2125 lbs, alternative 27mm SIR option adds 175 lbs. · STL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis percentage additions, subtractions, and fixed pounds. · STL STU rear wing Gurney flap terminology clarified from wicker to Gurney flap in mounting and chord rules. · GTL: Toyota MR2 Spyder 1999–2007 newly classified for GTL competition. · TA2 Gurney flap wording clarified: replace 'wicker bill' and 'wicker' with 'Gurney flap' throughout wing specifications. · STO rear wing rules clarify that wicker is called Gurney flap in two places; no performance change. · GT Gurney flap wording clarified: wickerbill and tab terminology replaced with Gurney flap throughout sections 9.1.2.F.7.b. · GTL Mazda 13B restrictor size addressed in response to letter 28518; see that letter for details. · STU request for alternate intake manifold denied; no change to rules. · GT3 and STU add Borg-Warner EFR6258 turbocharger to approved turbo lists. · STU large displacement turbo engines limited by GCR turbo list; no BoP change granted. · STU sequential shifters referred to Board of Directors for approval; no rule change effective. · GTL SIR stall test procedure clarified: system tested as raced, competitor must prevent air bypass behind restrictor. · STU Mazda 13B Bridge Port and Street Port added with 2550 lbs and 2250 lbs minimum weight respectively. · GTL wing mount openings excluded from square inch area limit. · STU Honda S2000 gains HKS Supercharger kits 12001-AH006 and 12001-AH010 as allowed options. · STU Lotus Elise Cup R and SC Exige SC gain 100 lbs minimum weight to 2300, 2500. · STU Volkswagen GTI/GLI MK5 and Jetta Mk4 may now install turbo inlet restrictor in OEM housing, per TIR spec. · STU Honda K20C1 Turbo I4 restrictor reduces from 36mm to 35mm. · STU GM Ecotech LNF now permitted without turbo, with LE5 head and intake manifold, meeting STL specs. · STU Porsche 944 now permits VW/Audi 1.8L and 2.0L turbo engines as alternates to original. · GTL wing mounting posts limited to 85 square inches exposed area each, measured flat from side view. · GTL wing mounting posts limited to 85 square inches each, measured flat from side view. · GTL wing endplates maximum area increased to 64 square inches from 8.5 by 3.0 inches rectangle. · GTL Mazda 12A street port minimum weight drops to 1950 lbs. · STU vehicles over 2951 lbs base weight may use 9 inch wide wheels, changed from 2950 lbs. · STU turbocharged engines now use base weight instead of minimum weight; DFI cars add 3% to base weight. · GT1, GT2, GT3, GTL, GTX may use bonded-glass factory windshields without clips or straps if attached per original specifications. · GTX Misc. adds Factory Five Type 65 Coupe R Ford 302/351 and 5.0/5.2L NA at 2600 lbs, plus Ferrari 458/488 Challenge, Ford FP350S, Chevrolet C6, Lamborghini Super Trofeo. · GTL adds Jetta Mk1 two-door classification effective 2020-01-01. · GTL Honda CRX 84-87 and 88-91 lose permission to use IRS with 2.5% weight penalty. · STU allows OEM electronic throttle bodies, manual conversion, cam changes, and manual-to-electronic conversion with same inner diameter.showhide
GTL GT Category Wording #29193wordingaddedGT1/GT2/GT3/GTL/GTX turbocharging and supercharging now permitted if listed on spec line.
STU Request for Advanced Aero Rule Wording Clarification. #29124wordingwordingSTU fender flare rule reworded: now per-corner up to 2" total, 1% weight penalty applies to entire modification.
GTL Request to change the Mazda 13b restrictor size #28518induction +175 lbsfasterinductionGTL Mazda 13B restrictor increases from 24mm to 26mm SIR, minimum weight rises to 2125 lbs, alternative 27mm SIR option adds 175 lbs.
STU Minimum Weight Determination #27695wordingwordingSTL and STU clarify weight adjustment calculation order: engine adjustments first, then chassis percentage additions, subtractions, and fixed pounds.
STU ST Gurney flap Wicker clarification #29012wordingwordingSTL STU rear wing Gurney flap terminology clarified from wicker to Gurney flap in mounting and chord rules.
GTL Request to classify 1999-2007 Toyota MR2 Spyder body #28870cars addedaddedGTL: Toyota MR2 Spyder 1999–2007 newly classified for GTL competition.
GTL TA2 Gurney flap wicker clarification #28874wordingwordingTA2 Gurney flap wording clarified: replace 'wicker bill' and 'wicker' with 'Gurney flap' throughout wing specifications.
GTL STO Gurney flap wicker clarification #28883wordingwordingSTO rear wing rules clarify that wicker is called Gurney flap in two places; no performance change.
GTL GT Gurney flap wicker clarification #28909wordingwordingGT Gurney flap wording clarified: wickerbill and tab terminology replaced with Gurney flap throughout sections 9.1.2.F.7.b.
GTL Mazda 13b Restrictor Size Follow up to Letter 28518 #29015wordingunclearGTL Mazda 13B restrictor size addressed in response to letter 28518; see that letter for details.
STU Request for Alternate Intake Manifold #26514wordingunclearSTU request for alternate intake manifold denied; no change to rules.
STU Request for Addition to GT3 Approved Turbo List #27576cars addedaddedGT3 and STU add Borg-Warner EFR6258 turbocharger to approved turbo lists.
STU Request BoP for my Car #29004wordingunclearSTU large displacement turbo engines limited by GCR turbo list; no BoP change granted.
STU Sequential Shifters in STU #29031wordingunclearSTU sequential shifters referred to Board of Directors for approval; no rule change effective.
GTL Stall Test #28709wordingwordingGTL SIR stall test procedure clarified: system tested as raced, competitor must prevent air bypass behind restrictor.
STU Rotary Help #27833cars addedaddedSTU Mazda 13B Bridge Port and Street Port added with 2550 lbs and 2250 lbs minimum weight respectively.
GTL GTL Wing Rule #28754aeroaddedaeroGTL wing mount openings excluded from square inch area limit.
STU Request to approve Honda S2000 HKS supercharger #27281otheraddedSTU Honda S2000 gains HKS Supercharger kits 12001-AH006 and 12001-AH010 as allowed options.
STU Request BoP on the Lotus #27637weight +100 lbsslowerweightSTU Lotus Elise Cup R and SC Exige SC gain 100 lbs minimum weight to 2300, 2500.
STU Turbo Inlet Restrictor On MK5 Volkswagen #27704otherslowerSTU Volkswagen GTI/GLI MK5 and Jetta Mk4 may now install turbo inlet restrictor in OEM housing, per TIR spec.
STU Honda K20C1 removal #27732engineslowerengineSTU Honda K20C1 Turbo I4 restrictor reduces from 36mm to 35mm.
STU Change GM LNF 2.0 Allowance to LSJ Engine for Viable STL 2.0 #27884engineaddedengineSTU GM Ecotech LNF now permitted without turbo, with LE5 head and intake manifold, meeting STL specs.
STU Alternate Engine for Porsche 944 #28259engineaddedengineSTU Porsche 944 now permits VW/Audi 1.8L and 2.0L turbo engines as alternates to original.
GTL Wing Mounting Upright Size #27641aeroaeroGTL wing mounting posts limited to 85 square inches exposed area each, measured flat from side view.
GTL Wing Mounting Upright Size #27641aeroaeroGTL wing mounting posts limited to 85 square inches each, measured flat from side view.
GTL GTL wing end plates addition #28243aerofasteraeroGTL wing endplates maximum area increased to 64 square inches from 8.5 by 3.0 inches rectangle.
GTL Clarification to letter #27406 #28309weight -50 lbsfasterweightGTL Mazda 12A street port minimum weight drops to 1950 lbs.
STU Please Modify the STU Wheel Size Rule for Clarity #27694weightfasterweightSTU vehicles over 2951 lbs base weight may use 9 inch wide wheels, changed from 2950 lbs.
STU Turbo Engine Cars Base Weight #28032wordingwordingSTU turbocharged engines now use base weight instead of minimum weight; DFI cars add 3% to base weight.
GTL Windshield Clips #27323otheraddedGT1, GT2, GT3, GTL, GTX may use bonded-glass factory windshields without clips or straps if attached per original specifications.
GTL Request Factory Five Daytona coupe classification #26308cars addedaddedGTX Misc. adds Factory Five Type 65 Coupe R Ford 302/351 and 5.0/5.2L NA at 2600 lbs, plus Ferrari 458/488 Challenge, Ford FP350S, Chevrolet C6, Lamborghini Super Trofeo.
GTL Request to Classify the MK1 two door Jetta #27648cars addedaddedGTL adds Jetta Mk1 two-door classification effective 2020-01-01.
GTL 88-91 Honda CRX Spec Line Correction #27233suspension & brakesremovedsuspension & brakesGTL Honda CRX 84-87 and 88-91 lose permission to use IRS with 2.5% weight penalty.
STU Request for an electronic throttle body #27342engineaddedengineSTU allows OEM electronic throttle bodies, manual conversion, cam changes, and manual-to-electronic conversion with same inner diameter.
1:59.948Kevin Boehm · fastest of 25 · top 5 within 3.5s
2:00.483Kevin Boehm · fastest of 25 · top 5 within 2.5s
143.8Kevin Boehm
2:06.997Peter Shadowen · fastest of 19 · top 5 within 4.0s
2:07.837Bill Ball · fastest of 18 · top 5 within 4.2s
131.1Peter Shadowen
+7.354squal +7.049s
106.1%qual 105.9%
35 rule changes (STU: 22, GTL: 13)9 cars added · 6 engine · 4 induction · 3 aero · 1 removed · 1 weight · 9 wording · 2 other · GTL Fun Cup Beetle engine weight set to 1850 lbs with Weber DMTL 32/34 induction. · STU wing assembly wording corrected: no part may be higher than roof height. · GTL Fun Cup Beetle removes reference to VW engine table; Fun Cup engines only permitted. · GTL Honda CRZ 10-14, CRZ 15-16, and Insight 00-06 gain alternate wheelbase option of 90.6 inches. · STU Nissan SR20DET removes -2mm penalty from Table B. · STU allows alternate intake manifolds on case-by-case basis; stock throttle device and manifold otherwise required. · STU aftermarket side skirts now allowed if they meet 3-inch ride height, lack ducts except jacks or exhaust, don't exceed fascia width, stay below door bottom, and don't reinforce chassis. · STU wheel flare wording clarified: each fender may be flared to 2" with 1% weight penalty, maintaining OEM profile. · GTL Fun Cup Beetle added, all model years, 2-door RWD, 94.5 in wheelbase, VW Fun Cup spec chassis. · GTX tube frame cars now allowed fuel injection with maximum 90mm throttle body. · GTX adds Ligier JS2 R classification with restrictor and minimum weight. · GTL Mazda 13B may use 25mm SIR with 175 lbs weight penalty added. · STL and STU ride height measurement clarified: lowest rocker panel point without driver, excluding pinch weld. · GT1 and GT2/3/Lite remove ride height ground clearance rules; cars may now touch ground when tires deflate. · STU Mazda 13B Bridge Port now permits ELITE ROTARY SHOP FD V2.0 intake manifold; stock throttle body requirement removed. · STU Mazda MZR gains alternate Goodwin intake manifold option with stock or Acura throttle body. · STU alternate suspension components rule moved from section E to section D. · STU Honda/Acura B20 now permits B16 or B18 VTEC cylinder head and matching intake manifold. · STU flared fenders up to 2" with 1% weight penalty moved from base to Advanced Aero. · STU Honda Civic Si TCA 2017- requires 37mm TIR throttle as of June 1, 2019. · STU BMW S54B32 OEM classified separately from E46, displacement 3246 cc, minimum weight 3300 lbs, OEM engine mandatory. · GTL Mazda 12A may use 28mm SIR plus 175 lbs. · GTL: Ford Mustang 94-04 body newly classified for GTL racing. · Honda Civic Si 2017- added to STU with 1500cc displacement, 2800 lbs minimum weight, OEM engine and bodywork, specific HPD parts allowed. · STU BMW E46 S54 OEM 3246cc added at 3300 lbs minimum; no Super Touring allowances, OEM intake and cams, 1mm overbore, compression +0.5 permitted. · STU Mazda 13B and 13B Bridge Port may use 13B RE or REW housings and intake with turbo removed. · STU Honda K24 may use intake part numbers 17100-RRB-A00 or 17100-PRB-A10. · STU Mazda 12A Bridge Port added, minimum weight 2550 lbs, Nikki or Auto-type carburettor with specified modifications. · STU World Challenge car weight rule deleted; no replacement specified. · STU AWD/RWD cars no longer must reduce restrictor 1 mm from table. · STU rear wing maximum 12" cord, 72 sq in end plates each, roof height max, body width limit. · GTL Mini 1275–1399 Iron and Aluminum Crossflow with OE common sump gearbox reduce weight by 125 lbs, up from 50 lbs. · GTL BMC thru Rover Group removes four long inactive Mini engines: 948, 970, 1071, 1098. · GTX FIA GT3: Audi R8 now 40 mm restrictor and 2900 lbs; BMW Z4 now 70 mm restrictor and 2800 lbs; Ferrari 488 now 35 mm restrictor, TIR, and 3025 lbs. · STU adds Honda K20C1 Turbo I4, 1996 cc, 3025 lbs minimum weight, 36mm TIR required.showhide
GTL Fun Cup Beetle #27334wordingwordingGTL Fun Cup Beetle engine weight set to 1850 lbs with Weber DMTL 32/34 induction.
STU Request to correct E&O advanced aerodynamics #27290wordingwordingSTU wing assembly wording corrected: no part may be higher than roof height.
GTL GTL #26960wordingwordingGTL Fun Cup Beetle removes reference to VW engine table; Fun Cup engines only permitted.
GTL Request CRZ wheelbase change #26896cars addedaddedGTL Honda CRZ 10-14, CRZ 15-16, and Insight 00-06 gain alternate wheelbase option of 90.6 inches.
STU Remove -2mm penalty from SR20DET Nissan #26982enginefasterengineSTU Nissan SR20DET removes -2mm penalty from Table B.
STU Request clarification for manifold and throttle in STU #27004wordingwordingSTU allows alternate intake manifolds on case-by-case basis; stock throttle device and manifold otherwise required.
STU Request to clarify afterrmarket side skirts exhaust exit #26814aeroaddedaeroSTU aftermarket side skirts now allowed if they meet 3-inch ride height, lack ducts except jacks or exhaust, don't exceed fascia width, stay below door bottom, and don't reinforce chassis.
STU Wheel Flare wording #26872wordingwordingSTU wheel flare wording clarified: each fender may be flared to 2" with 1% weight penalty, maintaining OEM profile.
GTL Request to Classify VW Fun Cup Beetle #25986cars addedaddedGTL Fun Cup Beetle added, all model years, 2-door RWD, 94.5 in wheelbase, VW Fun Cup spec chassis.
GTL Request GTX Fuel injection for previous GT-1 tube frame cars #26141engineaddedengineGTX tube frame cars now allowed fuel injection with maximum 90mm throttle body.
GTL Request to Classify Ligier JS2 R #26535cars addedaddedGTX adds Ligier JS2 R classification with restrictor and minimum weight.
GTL Request for GTL Mazda 13B SIR Increase with Penalty #26572engineaddedengineGTL Mazda 13B may use 25mm SIR with 175 lbs weight penalty added.
STU Request Ride Height Clarification #26597wordingwordingSTL and STU ride height measurement clarified: lowest rocker panel point without driver, excluding pinch weld.
GTL Request Ride Height Clarification #26600wordingfasterGT1 and GT2/3/Lite remove ride height ground clearance rules; cars may now touch ground when tires deflate.
STU Request to Use Japanese Mazda 13b Intake Manifold #25790engineaddedengineSTU Mazda 13B Bridge Port now permits ELITE ROTARY SHOP FD V2.0 intake manifold; stock throttle body requirement removed.
STU Request Alternate Intake for Mazda MZR In a Rear Wheel Drive App. #26352inductionaddedinductionSTU Mazda MZR gains alternate Goodwin intake manifold option with stock or Acura throttle body.
STU E&O Suspension #26424wordingwordingSTU alternate suspension components rule moved from section E to section D.
STU Revisit B20 VTEC #26530engineaddedengineSTU Honda/Acura B20 now permits B16 or B18 VTEC cylinder head and matching intake manifold.
STU Move Flared Fenders to STU Advanced Aero #26564aeroaeroSTU flared fenders up to 2" with 1% weight penalty moved from base to Advanced Aero.
STU TCA Civic SI E&O #26606inductionslowerinductionSTU Honda Civic Si TCA 2017- requires 37mm TIR throttle as of June 1, 2019.
STU S54 Spec line #26620cars addedcars addedSTU BMW S54B32 OEM classified separately from E46, displacement 3246 cc, minimum weight 3300 lbs, OEM engine mandatory.
GTL Request Mazda 12a Rotary SIR Increase #26081inductionaddedinductionGTL Mazda 12A may use 28mm SIR plus 175 lbs.
GTL Request to Classify Mustang 2 Body in GTL #26222cars addedaddedGTL: Ford Mustang 94-04 body newly classified for GTL racing.
STU Request to Class Assignment for 2017 Civic #24287cars addedaddedHonda Civic Si 2017- added to STU with 1500cc displacement, 2800 lbs minimum weight, OEM engine and bodywork, specific HPD parts allowed.
STU Request to run E46 3246cc in STU #25126cars addedaddedSTU BMW E46 S54 OEM 3246cc added at 3300 lbs minimum; no Super Touring allowances, OEM intake and cams, 1mm overbore, compression +0.5 permitted.
STU Engine Classification for Rotary #25564engineaddedengineSTU Mazda 13B and 13B Bridge Port may use 13B RE or REW housings and intake with turbo removed.
STU K24/K20 Head Swap Clarification/Amendment #25899otheraddedSTU Honda K24 may use intake part numbers 17100-RRB-A00 or 17100-PRB-A10.
STU Request to Classify 12a Bridge Ported Rotary Engine #25985cars addedaddedSTU Mazda 12A Bridge Port added, minimum weight 2550 lbs, Nikki or Auto-type carburettor with specified modifications.
STU World Challenge Car Eligibility #26387wordingunclearSTU World Challenge car weight rule deleted; no replacement specified.
STU Request a phone call for discussion regarding weight #26398inductionfasterinductionSTU AWD/RWD cars no longer must reduce restrictor 1 mm from table.
STU Advanced Aero E&O #26413aeroaddedaeroSTU rear wing maximum 12" cord, 72 sq in end plates each, roof height max, body width limit.
GTL Request for GTL Mini Adjustments #25754weightfasterweightGTL Mini 1275–1399 Iron and Aluminum Crossflow with OE common sump gearbox reduce weight by 125 lbs, up from 50 lbs.
GTL BMC thru Rover Group remove long inactive mini #25771removedremovedGTL BMC thru Rover Group removes four long inactive Mini engines: 948, 970, 1071, 1098.
GTL GTX Homologation table update #26034otherunclearGTX FIA GT3: Audi R8 now 40 mm restrictor and 2900 lbs; BMW Z4 now 70 mm restrictor and 2800 lbs; Ferrari 488 now 35 mm restrictor, TIR, and 3025 lbs.
STU Request to Equalize Direct Injected Turbo Cars #24890cars addedaddedSTU adds Honda K20C1 Turbo I4, 1996 cc, 3025 lbs minimum weight, 36mm TIR required.
Every event the class ran, at any track, oldest to newest on the chart and newest first in the table. Each point is the class's best lap as a share of STU's best on the same day: the weather and the day cancel out, so one figure compares across years where lap times cannot; a class that suits one track more than another still reads differently there. It still moves when the yardstick's own balance changes or its field thins, and an event the yardstick did not run has no point. A best from fewer than three cars is greyed. The rule changes that took effect between two events are folded between their rows.